Guide

Which Welding Rod Should You Use for Cast Iron?

Use a nickel-based stick electrode made for cast iron. Pure nickel rods (ENi-CI) leave soft, machinable welds and suit thin parts and cold repairs. Nickel-iron rods (ENiFe-CI) make stronger welds and suit ductile iron and joints to steel. Cast iron rods are not sold by a number like 6011 or 7018. You look for the AWS class instead.

Updated 2026-11-12 · Based on published specifications and maker information

Top picks from our best welding rod for cast iron comparison

Why cast iron needs a special rod

Cast iron holds a lot of carbon, which makes it hard and brittle. When a weld cools, the metal shrinks. Ordinary steel rods make a hard, stiff weld that can't give with that shrinking, so cracks often form in the weld or in the metal beside it.

Nickel helps because nickel-based deposits stay softer and more ductile as they cool. They stretch a little instead of cracking. That is why nearly every rod made for cast iron is built around a nickel core wire, and why most advice about this topic comes down to choosing the right nickel rod.

Some welders have had luck with stainless rod on cast, and it can work on some repairs. A nickel rod made for the job is still the more dependable choice, especially on parts that matter.

What number is the right welding rod for cast iron?

There is no single rod number. Stick rods for steel use codes like 6011 or 7018, but cast iron rods are classed under AWS A5.15. The two classes you will see are ENi-CI and ENiFe-CI.

Pure nickel is ENi-CI, with about 99% nickel in the core. Nickel-iron is ENiFe-CI, with about 55% nickel. Some sellers write the class as ENi-C1 or ENiFe-C1, which means the same thing. If the package shows one of these classes, it is a cast iron rod.

Pure nickel vs nickel-iron: the main differences

Both types work on gray iron. The choice usually comes down to how the part will be used and whether you need to machine the weld afterward.

Our best welding rod for cast iron page lists both types on one spec sheet, so you can compare alloy, nickel content and pack size side by side.

FeaturePure nickel (ENi-CI)Nickel-iron (ENiFe-CI)
Nickel contentAbout 99%About 55%
Weld depositSoft, easy to machineStronger, usually harder to machine
Best onThin sections, normal gray iron, cold weldsDuctile iron, high-strength gray iron, joints to steel
Cracking riskLow when welded cold or lightly preheatedLower shrinkage stress, helps with contaminated or low-grade iron
PreheatOften none or cold weldSome makers require it

Which rod fits which job

Match the rod to the part and to what you plan to do after welding. These are the common cases:

  • Thin castings and broken pieces: pure nickel. It puts in a soft deposit and runs cold. The Fox Alloy ENi-CI listing, with 99% nickel, names thin parts as a use and lists preheat as none or cold weld.
  • Parts you must drill, tap or mill afterward: pure nickel. Listings for the SÜA and Weldcote 99% rods both say the deposit is machinable.
  • Ductile (nodular) iron or high-strength gray iron: nickel-iron. The Fox Alloy ENiFe-CI rod is listed for gray and nodular iron.
  • Cast iron joined to steel: nickel-iron is a good fit, and several pure nickel rods also list steel joints. Check the listing for the exact base metals.
  • Dirty or low-grade castings: nickel-iron. The WeldingCity 55% listing says it handles iron with excess phosphorus or other contaminants.
  • Hard, dense welds on gray iron grades 30, 40 and 50: the Forney 55% rod is listed for those grades, but it is not easily machined and needs carbide tools.

Choosing diameter, rod count and preheat

Diameter changes how much heat goes into the part. A 3/32 in (0.09375 in) rod puts in less heat, which helps on thin sections. A 1/8 in (0.125 in) rod fills larger joints faster. Most rods on our page are 1/8 in, and two are 3/32 in.

Pack size matters too. Rod counts on our page run from 5 to 10, and net weights run from 0.5 lb to 4.4 lb on the models that list them. One crack may need only a few rods. Rebuilding worn areas or doing regular repairs calls for a larger supply.

Preheat is where makers disagree. Two pure nickel listings say none or cold weld. One nickel-iron listing says preheat is required to prevent cracking. If the maker gives no guidance, follow standard cast iron practice for your part, and when in doubt, warm the casting evenly and let it cool slowly.

For a deeper look at specific products, see our comparison of cast iron welding rods.

Basic technique to avoid cracks

Good rod choice only gets you part of the way. How you weld matters just as much. These steps are standard practice for stick welding cast iron:

  • Clean the area to bare metal. Grind out oil, paint and rust, and remove old weld material.
  • If the part is cracked, drill a small hole at each end of the crack to stop it from spreading.
  • Grind a V groove along the crack so the weld can fill the full depth.
  • Weld short beads, about an inch at a time, using low current and keeping the rod fairly straight.
  • Peen each bead lightly with a ball-peen hammer while it is still warm to relieve stress.
  • Let the part cool slowly. Skip the quench, and keep it out of drafts.

Safety notes

Welding involves electric shock, arc light, sparks and fumes. Wear a welding helmet with the right shade lens, dry insulated gloves, and non-flammable clothing. Safety glasses go under the helmet because grinding and peening throw sharp chips.

Wear hearing protection when grinding. Work in a space with good ventilation, because cast iron castings can carry oil, coatings and residues that give off fumes when heated. Never weld a fuel tank, a sealed container or anything that held flammable liquid. Keep a fire extinguisher close, and move combustibles away.

Preheated castings stay hot for a long time, so handle them with tongs or heavy gloves. Keep your rods dry and sealed, since damp rods weld poorly.

Frequently asked questions

Can I use a regular 7018 or 6011 rod on cast iron?

It is not recommended. Steel rods make a hard, stiff weld that tends to crack as the casting cools. A nickel-based rod made for cast iron is a much safer choice.

Do I always need to preheat cast iron?

Not always. Pure nickel rods are often used cold, and two listings on our page say none or cold weld. One nickel-iron listing says preheat is required. Follow the maker's guidance for your rod.

Which rod is better for ductile iron?

Nickel-iron (ENiFe-CI) is the usual pick. The Fox Alloy ENiFe-CI listing names gray and nodular (ductile) iron among its uses.

Can I use a MIG or flux-core welder on cast iron?

Stick welding with nickel rods is the common method for cast iron repair. Nickel wire for MIG exists, but this guide focuses on stick rods, so check the wire maker's instructions before trying it.

Compare the products