Spade Bit Set vs Regular Bit Set: What Differs?
A spade bit set is built for boring large, fast, fairly rough holes in wood. A regular (twist) drill bit set drills smaller, more precise holes and works in more materials. If you run wire, pipe or cable through framing, get spade bits. If you need pilot holes, hardware holes or metal drilling, get a regular set.
The short version: two bits for two jobs
The two sets overlap less than people expect. A spade bit is a flat paddle with a center point and cutting edges. It chews out a big hole quickly and leaves a rougher wall. A regular twist bit has spiral flutes that carry chips out of a narrow hole and cut a cleaner, more accurate bore.
Many people end up owning both. Spade bits handle the big holes in wood, and twist bits handle everything small, including pilot holes for screws. This guide uses "regular bit set" to mean a standard twist drill bit set.
How the bits are shaped
A spade bit has a flat blade with a point in the middle. Some have a threaded tip that screws into the wood and pulls the bit forward. Without one, the center spur needs more pressure to start and keep cutting. Double cutting spurs on the edges score the wood fibers, which cuts down on breakout at the hole's edge.
A twist bit has a round body with spiral grooves. The grooves pull chips up and out as you drill. That is why twist bits can go deep in a small diameter without clogging. A spade bit has a shallow paddle, so you pull it out now and then to clear chips, especially in deeper holes.
Some spade sets add deep slots or grooves on the paddle to clear chips faster. These help, but the basic design stays a flat blade made for speed over finish.
Size range and what you can drill
Size is the clearest difference. Our top-ranked spade set, the Jorgensen 71101, covers 1/4 in to 1-1/2 in across 13 bits, plus a quick-load connector for 14 pieces total. That range is aimed at holes for wiring, plumbing and larger fasteners. Several other sets on our spade list cover the same span.
A regular set is built around smaller holes and finer steps between sizes. It suits pilot holes, hinge and hardware holes, and drilling in metal or plastic. Spade bits are meant for wood, and the listings we compare describe wood use. Using a spade bit on a metal panel is a poor fit for the blade shape.
Bit length also differs. Our spade listings show 6 in bits, and two sets list 16 in for drilling through studs and beams. The Pinoze sets include a 6 in extension rod that extends bits to 12 in. Regular sets are usually shorter, so check length if you need to reach through thick lumber.
Side by side
Here is how the main bit types compare in general. Specific numbers for spade sets come from the listings on our comparison page.
| Feature | Spade bit set | Regular twist bit set | Forstner bit set |
|---|---|---|---|
| Best for | Fast, large holes in wood | Small, precise holes in wood, metal and plastic | Clean, flat-bottomed holes in wood |
| Hole finish | Rougher walls, some breakout | Cleaner in small sizes | Very clean |
| Speed | Fast | Moderate | Slower |
| Chip clearing | Needs backing out in deep holes | Spiral flutes carry chips out | Needs backing out in deep holes |
| Typical use | Wiring, plumbing, rough carpentry | Pilot holes, hardware, general drilling | Cabinet and furniture work |
Which set to buy
Start with the hole you need. If it is large and sits inside a wall, stud or joist, a spade set is the practical choice. Check the smallest and largest sizes and how many sizes you actually get, since a few sets give two bits of one size instead of more sizes. Our best spade bit set page ranks sets by these specs, including threaded tips, double spurs and connectors.
If you mostly drill small holes or work in several materials, a regular set is the better first purchase. Our best drill driver bit set page is the place to compare those. If the hole's appearance matters, such as a visible hole in a cabinet or a shelf, look at a best Forstner bit set instead, since spade bits leave a rougher edge.
- Choose a spade set for fast, large holes in framing and rough wood.
- Choose a regular set for pilot holes, metal, plastic and small hardware holes.
- Choose Forstner bits when a clean, flat-bottomed hole matters.
- Choose a long or extendable spade bit when you must drill through studs or reach into tight spots.
Using spade bits well and safely
Check the shank first. A 1/4 in hex shank fits most drills and impact drivers and resists slipping. Several of the listings state a maximum speed of 1500 RPM, so keep the drill at a moderate speed rather than running it flat out. One listing also advises low speed with steady pressure.
Spade bits can grab and kick the drill when they break through or hit a knot or nail. Hold the drill with both hands, brace yourself, and ease off as the tip exits the back of the workpiece. Clamp small pieces so they cannot spin.
Follow these basics every time:
- Wear safety glasses, since chips and splinters fly out.
- Use hearing protection with larger bits and long sessions.
- Unplug corded drills or remove the battery when changing bits.
- Before drilling in walls, check for wiring and pipes behind the surface.
- On a ladder, keep your balance and avoid reaching, since a grabbed bit can pull you off.
Frequently asked questions
Can I use a spade bit in metal?
No. Spade bits are made for wood and soft materials. Use a twist bit designed for metal, with slow speed and steady pressure.
Do I need a threaded tip?
It is not required, but it helps the bit start on your mark and pull itself into the wood with less push. Sets without one rely on a center spur and need more pressure.
Will a spade bit fit my impact driver?
Most spade sets with a 1/4 in hex shank fit both drills and impact drivers. Check the listing for the shank type before buying. Our best impact driver bit set page covers sets made for impact drivers.
How do I reduce splintering when the bit exits?
Clamp a scrap board behind the workpiece and drill into it, or drill from both sides once the tip pokes through. Double spurs also help reduce breakout.
Jorgensen 71101Best overall
WORKPRO W004521AHeat-treated steel bits
Pinoze P008E002Extension reaches 12 in