How to Weld Exhaust Without Burning Through the Metal
Burn-through comes from too much heat sitting in thin tubing. Keep the settings low, fit the joint tightly, tack in short bursts, and weld in small sections so the metal can cool. A machine that runs a smooth arc at low settings makes this much easier.
Why exhaust tubing burns through so easily
Exhaust tubing has thin walls, so there is very little metal to absorb heat. If the arc lingers in one spot, the puddle grows, sags, and drops out as a hole. Most burn-through is a heat-control problem, not a skill problem.
Three things add heat: settings that are too high, a slow travel speed, and a poor fit-up that forces you to fill a gap. Fix those three and most holes disappear. Rust, oil, and coatings also make the arc erratic, which leads to sudden hot spots.
Prep the joint before you strike an arc
Clean metal gives a calm, predictable puddle. Good prep is the cheapest way to avoid burn-through.
Fit-up matters just as much. A tight butt joint or a snug slip fit needs less filler and less heat than a joint with a wide gap.
- Cut the pipe square and deburr the edges so the pieces meet evenly.
- Grind or sand the weld area to bright metal, inside and outside if you can reach it.
- Remove any coating, paint, or heavy rust from the weld zone. Coated or galvanized metal gives off harmful fumes, so ventilate well.
- Wipe off oil and grease with a suitable degreaser and let it dry fully.
- Clamp or tack the parts so they cannot shift as the metal heats up.
- Attach the ground clamp to clean bare metal close to the joint.
Starting settings for thin exhaust pipe
No single number works for every machine, tubing size, or wall thickness. The reliable method is to start low, test on a scrap piece of the same tubing, and raise the heat only until the bead fuses without a hole. Your welder's chart inside the door or in the manual is the best first reference.
If your machine has synergic control, pick the wire diameter and gas type, then use the suggested setting as a starting point. Trim it down a little for thin pipe. Thinner wire also helps, since it needs less heat. For example, the ARCCAPTAIN MIG200 lists support for .023 in and .030 in solid wire, though the .023 in roller is sold separately.
| Control | What to do on thin tubing |
|---|---|
| Voltage or amperage | Start low and raise in small steps on scrap |
| Wire feed speed | Keep it slow so the arc stays small and steady |
| Wire diameter | Use the thinner wire your machine supports |
| Shielding gas | Gas MIG gives a cleaner, flatter bead than flux core |
| Trigger mode | Use 2T for short tacks, 4T for longer runs |
| Burn-back and inductance | Adjust if the wire sticks or the arc feels harsh |
Technique that keeps heat under control
Technique is where you win or lose the joint. Think short and quick, not long and slow.
Working in small sections lets the tubing shed heat between welds. Pause or skip around the joint so no single area gets too hot.
- Test your settings on a scrap piece of the same tubing.
- Place four or more small tack welds evenly around the joint, each one a quick pulse.
- Weld a short section, about an inch or less, then stop.
- Move to the opposite side of the pipe and weld another short section.
- Keep a steady travel speed and aim the arc at the leading edge of the puddle.
- If a hole starts, stop at once. Let the area cool, then patch from the edges inward with quick tacks.
- Let the pipe cool naturally. Do not quench it with water.
Choosing a welder that helps prevent burn-through
The most useful trait is low-end control, not top output. A machine that holds a stable arc at low settings beats one with a big maximum amperage. Our best welding for exhaust page compares these specs on one sheet, and it favors gas MIG or TIG, fine-tuning controls, and manageable weight.
Among the models listed there, the YESWELDER MIG-205DS PRO publishes a 58 to 858 in/min wire feed range and allows -3V to 3V voltage trim, which gives you room to dial heat down. The ARCCAPTAIN MIG200 stores 10 parameter sets per welding mode, so you can recall a thin-tubing setup. The BILT HARD WLD-1603 adds inductance adjustment in MIG mode.
Weight matters if you weld under a car. The BESTMIG 165S weighs 12.1 lb and is rated for mild steel up to 0.19 in, while the FEMEROL MTC200PRO weighs 42 lb and adds HF TIG and a plasma cutter. If you want to compare more options before choosing, see our full exhaust welder comparison.
Safety notes before you weld
Welding exhaust usually means working under a vehicle, so set up carefully.
Disconnect the vehicle battery before welding near wiring or electronics. Remove or shield fuel lines, tanks, and anything flammable, and never weld near fuel vapor. Support the vehicle on rated jack stands or a lift, never on a jack alone. Wear an auto-darkening helmet, gloves, long sleeves, and eye protection under the helmet, and use hearing protection while grinding. Weld in a ventilated space, and keep a fire extinguisher within reach. Check that your machine's input voltage setting matches your outlet before you power it on.
Frequently asked questions
Can a beginner weld exhaust at home?
Yes, with practice. Start on scrap tubing, use a machine with synergic control, and work in short tacks. Practice until you can fuse a joint without holes before you work on the car.
Is flux core a good choice for exhaust?
It works, but gas MIG usually leaves a cleaner, flatter bead and less slag. Slag is harder to clean from inside a thin tube joint.
Why does my weld keep spattering and blobbing?
Dirty metal, wire speed set too high, or welding over an old flux-core weld are common causes. Clean back to bright metal and lower the wire feed.
How do I fix a hole I already burned?
Stop and let the area cool. Then rebuild the edge of the hole with quick tacks, working from the solid metal inward, and let it cool between tacks.
Is TIG better than MIG for thin exhaust?
TIG offers the most heat control, especially on stainless. It takes more practice, and some machines sell the TIG torch separately, so check what is included.
YESWELDER MIG-205DS PROBest overall
ARCCAPTAIN MIG200Repeatable settings via presets
BILT HARD WLD-1603Arc tuning with inductance