How to Weld an Exhaust Pipe With a Stick Welder
You can weld an exhaust pipe with a stick welder if you use a small rod, usually 1/16 or 3/32 inch, and keep the amperage low so the thin wall does not blow through. Tack the joint, run short beads, and put most of the heat on the thicker flange or collar rather than the pipe. Stick is a workable repair method, but gas MIG or TIG gives cleaner results on thin tubing.
Is stick welding a good fit for exhaust pipe?
Stick welding was not designed for thin tubing. Most exhaust pipe has a thin wall, and a stick arc is hot, digs in deeply and throws slag. That makes burn-through the main risk, especially for beginners.
Still, many people repair exhaust with a stick welder because it is the machine they already own. It works best on heavier pieces such as flanges, hangers, thick-wall pipe and rusty repair sections. On very thin or stainless tubing, expect more frustration and more cleanup.
The rest of this guide shows how to get the best result from a stick setup and how to tell when it is time to switch processes.
What size welding rod for exhaust pipe
Small rods win here. A smaller diameter rod needs less current, and less current means less heat in a thin wall. As a general rule, start with 1/16 inch or 3/32 inch rods and avoid anything larger on the pipe itself.
For rod type, an E6013 is a common choice for thin mild steel because it runs a soft, steady arc at low current and has easy slag removal. An E7014 also works for similar jobs. E6011 digs deeper and is harder to control on thin metal, so save it for dirty or rusty thick parts. Always check the amperage range printed on the rod box, since it varies by brand.
Use the table below as a starting point, then adjust on scrap pipe of the same wall thickness.
| Situation | Rod size | Rod type to consider | Heat approach |
|---|---|---|---|
| Thin mild steel pipe, pipe to pipe | 1/16 in | E6013 | Lowest stable current, short beads |
| Standard pipe to thicker flange | 1/16 or 3/32 in | E6013 or E7014 | Aim the arc at the flange, touch the pipe edge |
| Heavy-wall pipe or brackets | 3/32 in | E6013 or E7014 | Moderate current, check for burn-through |
| Rusty or dirty thick repair | 3/32 in | E6011 | Grind first anyway; expect a deeper arc |
Prep and safety before you strike an arc
Good prep does more for your weld than any setting. Take your time here.
Exhaust work puts you under a vehicle, near fuel and around coated metal, so treat the safety steps as part of the job.
- Let the system cool fully, and support the car on jack stands rated for its weight. Never work under a car held only by a jack.
- Disconnect the battery to protect the electronics from stray current.
- Check for fuel lines, fuel tank, brake lines, wiring and plastic parts near the work. Shield or remove them, and keep a fire extinguisher within reach.
- Grind to bare, shiny metal. Rust, oil, soot and aluminized or galvanized coatings cause porosity, and the fumes from coatings are harmful. Work outdoors or with strong ventilation, and wear a respirator suited to welding fumes.
- Wear a welding helmet, leather gloves, a flame-resistant long sleeve and safety glasses under the helmet for grinding. Use hearing protection while grinding.
- Clamp the ground close to the joint on clean metal. Vice grips on the pipe a few inches from the weld area work well, as long as the contact is solid.
- Never weld on a pipe that held fuel, or on a sealed section, since trapped vapor or pressure can be dangerous. Leave pipes open at both ends.
Step by step: welding the joint
Cut the pipe square and fit it tight. Big gaps force you to hold the arc longer, which is how holes start. Use a slip joint or a sleeve for repairs when you can.
Then follow this order.
- Set the current near the low end of the rod's range. Try a few beads on scrap pipe of the same wall thickness.
- Tack the joint in three or four spots around the pipe. Short tacks hold alignment and spread out the heat.
- Strike the arc on the thicker piece, such as the flange, and drag the puddle toward the pipe edge so both sides wet in.
- Run short beads of about an inch, then stop. Let the metal cool a moment before moving to the opposite side of the pipe.
- If a hole opens, stop, let it cool and grind it clean. Bridge it with a quick touch of the rod, not a long hold.
- Chip the slag when each bead cools and check for pinholes. Fill them with a short extra pass.
- Finish by checking the joint for leaks once the engine is running. Look for a soot trail or listen for a hiss.
Common problems and quick fixes
Holes in the pipe mean too much heat or too long a pause on the thin side. Lower the current, move faster and keep the arc on the thicker part.
A rod that sticks usually means the current is too low or the arc is too short. Raise the setting slightly and hold a gap about the width of the rod core.
Porosity, which looks like tiny holes in the bead, points to dirty metal, damp rods or leftover coating. Regrind and keep the rods in a dry container.
Weak beads that sit on top of the metal mean the arc did not reach the base metal. Slow down a little and angle the rod toward the thicker side.
When to switch from stick to MIG or TIG
If you weld exhaust often, consider a process with finer control. Gas MIG gives cleaner, flatter beads with less slag to clean from inside the joint. TIG gives the most heat control, which suits stainless systems.
Our best welding for exhaust page lists machines side by side. Look for a low wire feed speed, synergic control and voltage trim rather than raw amperage, because thin walls reward gentle settings. For example, the YESWELDER MIG-205DS PRO lists a 58 to 858 in/min wire feed range and a voltage trim of -3V to 3V.
Many multi-process welders also include a stick mode, so you can keep stick for heavier jobs. The BESTMIG 165S lists Gas MIG, flux core, lift TIG and stick, and weighs 12.1 lb, which helps if you move the machine around under a car. You can compare more options on our exhaust welder comparison to see which published specs matter most for your work.
Frequently asked questions
Can I stick weld stainless steel exhaust?
It is possible with stainless electrodes, but the thin wall makes it hard to control. TIG is usually the better choice for stainless.
Do I need to remove the exhaust from the car to weld it?
Removing it is safer and gives you better access. If you weld in place, protect fuel lines, wiring and the tank, and disconnect the battery.
Should I use DC or AC on a stick welder for exhaust?
DC is smoother and easier on thin metal. Use AC only if that is all your machine offers, and pick rods rated for it.
Why does my weld leak even though it looks complete?
Pinholes and gaps along the toe of the bead are common culprits. Clean the joint, then add a short pass over the leak spot.
YESWELDER MIG-205DS PROBest overall
ARCCAPTAIN MIG200Repeatable settings via presets
BILT HARD WLD-1603Arc tuning with inductance