How to Use a Router With an Edge Guide on Wood
To use a router with an edge guide, attach the guide to the router base, set the distance from the bit to the fence, press the fence against the board's edge, and feed the router steadily so the guide follows that edge. Make shallow passes and test on scrap first. The result is a groove, dado or rabbet that runs perfectly parallel to the edge.
What an edge guide does
An edge guide is a fence that bolts to your router base on one or two rods. You slide it in or out to set how far the bit sits from the board's edge, then lock it with a knob. As you push the router along, the fence rides against the edge of the wood and keeps the cut straight and parallel.
This is different from using a bearing-guided bit, such as a roundover or chamfer bit. Those bits shape the edge itself, and the bearing does the guiding. An edge guide is for cuts set back from the edge, like grooves for panels, shallow dadoes, or rabbets made with a straight bit. If you are shopping for a router that handles both jobs well, our best router for wood page compares options for woodworking.
What you need before you start
Gather everything first so you are not hunting for tools with a spinning bit nearby.
- A router with an edge guide that fits its base (check that the rods and knobs match your model)
- A sharp straight bit sized for the groove you want
- A wrench or collet wrench for the bit
- Clamps and a non-slip mat or bench stop to hold the board
- A piece of scrap from the same board for test cuts
- A tape measure or calipers
- Safety glasses, hearing protection, and a dust mask
Safety first
Routers spin bits at very high speeds and throw chips and dust. Wear safety glasses and hearing protection every time, and a dust mask when cutting wood, especially MDF and hardwoods.
Always unplug the router, or remove the battery on a cordless model, before changing a bit or adjusting depth. Clamp the workpiece so it cannot move, and keep both hands on the router handles. Keep the cord clear of the bit's path. Let the bit stop completely before you set the router down.
Step-by-step: cutting a groove with an edge guide
Follow these steps in order for a clean, repeatable cut.
- Unplug the router and install the bit. Insert the shank fully, then back it out slightly and tighten the collet firmly.
- Mount the edge guide on the base and snug the knobs lightly.
- Set the offset. Measure from the edge of the bit's cutting side to the face of the fence. That distance is how far the groove sits from the board's edge.
- Set a shallow bit depth. Most woodworkers cut deep grooves in several passes rather than one heavy one, which reduces tear-out and strain on the motor.
- Clamp the board securely so the edge you are guiding on is accessible and straight.
- Test on scrap. Make a pass, measure the result, and adjust the fence or depth as needed.
- Rest the router on the board with the bit clear of the wood, press the fence firmly against the edge, and switch the router on.
- Lower or feed the bit into the wood and move at a steady pace. Keep side pressure on the fence the whole way.
- Lift the router off only after the bit has cleared the end of the cut, and wait for it to stop spinning.
- Increase the depth a little and repeat until you reach the final depth.
Feed direction and technique
Feed the router against the rotation of the bit. This helps the cutter bite properly and gives you control. If the router feels like it is pulling itself along or grabbing, you are probably moving the wrong way. Check your router's manual for the correct direction for your setup.
Keep steady pressure toward the fence so the guide never drifts off the edge. Do not force the router forward. If it slows or the motor sounds strained, the pass is too deep or the bit is dull.
Start with the fence flat against the board before the bit touches the wood, and keep it there until the bit exits. Short boards are harder to guide, so clamp a longer scrap piece at each end to give the fence more support. This also helps prevent the bit from chipping the end grain as it exits.
Choosing the right setup for the job
Different cuts call for different bits and approaches. This table gives a quick overview.
If you are still deciding which tool to buy, our best router comparison covers the general options, including how they differ in features and handling.
| Job | Typical bit | Edge guide use | Tip |
|---|---|---|---|
| Groove for a panel or back | Straight bit | Fence sets groove distance from the edge | Cut in light passes |
| Rabbet along an edge | Straight bit or rabbeting bit | Fence controls rabbet width with a straight bit | Test the fit on scrap |
| Dado across the width | Straight bit | Often better with a straight clamped guide | Edge guides work best along the grain |
| Edge profile (roundover, chamfer) | Bearing-guided bit | Usually not needed | The bearing follows the edge |
Common problems and fixes
Wavy or wandering cuts almost always come from inconsistent pressure on the fence. Keep a firm sideways push, and make sure the board's edge is straight. If the edge is bowed or rough, the groove will follow it.
Burn marks usually mean a dull bit, a pass that is too slow, or a cut that is too deep for one pass. Take lighter passes and keep the router moving.
Tear-out at the end of a cut happens when the bit breaks through the last fibers. Back the board with a scrap piece, or make a very light final pass.
If the fence slips, tighten the locking knobs and check that the rods are fully seated. Recheck your offset on scrap after any adjustment, since a slight shift changes the groove position.
Frequently asked questions
Can I use an edge guide on a curved board?
Standard straight edge guides work best on straight edges. Some come with a circle or curve option, but for tight curves a template and a bearing bit usually give a better result.
How far from the edge can I cut with an edge guide?
That depends on the length of the guide's rods and the router model. Check your guide's specifications. For cuts farther in, a clamped straight edge used as a fence is a common alternative.
Do I need to use the edge guide on both sides of the router?
Many guides use two rods for stability, but a single fence on one side is enough for most cuts. Just keep the fence pressed against the edge the whole way.
Should I make the cut in one pass?
For anything beyond a shallow cut, several light passes give cleaner results and are safer. Deep single passes can burn the wood and overload the motor.
Skil RT1324-00
Bosch 1617EVSPKPlunge and fixed kit
Metabo HPT M3612DAQ4