Guide

How to Use a Router Table for Safe, Accurate Cuts

Use a router table by securing the fence, setting the bit height with a test piece, and feeding the wood against the bit's rotation with push blocks. For most table work, a fixed-base router in the mid-power range handles common bits, and larger panel-raising bits call for more power. Take light passes, keep your hands clear, and wear eye and hearing protection every time.

Updated 2026-11-12 · Based on published specifications and maker information

Top picks from our best router comparison

Check your setup and safety gear first

A router table turns a handheld tool into a stationary one. The bit points up through the table, and you move the wood past it. That makes cuts steadier, but it also puts a spinning bit close to your hands, so preparation matters.

Before you plug in, make sure the router is locked firmly into the table, the insert plate is flush with the surface, and the fence is clamped tight. Unplug the router whenever you change a bit or adjust the height by hand.

  • Wear safety glasses or a face shield, since chips and dust fly in every direction.
  • Wear hearing protection, because routers are loud, especially at full speed.
  • Use a dust mask and connect dust collection at the fence if your table has a port.
  • Skip loose sleeves, gloves, and dangling jewelry that could catch on the bit.
  • Keep a push block, push stick, and featherboard within reach before you start.

What size router works best in a table

Many people ask what size router to use. The honest answer is that it depends on the bits you plan to run. Small roundover, chamfer, and rabbet bits work fine with a compact router. Large profile bits, such as raised-panel or tall cove bits, remove a lot of wood and need a stronger motor and a variable speed control.

Look for a router that allows height adjustment from above the table, accepts both common collet sizes, and has variable speed. A 1/2 inch collet holds larger bits more securely than a 1/4 inch one, so choose it when you can.

Router classTypical power rangeBest for
CompactAbout 1 to 1.75 hpSmall profiles, light edge work, trim bits
Mid-sizeAbout 2 to 2.25 hpMost general table work, joinery bits, moderate profiles
LargeAbout 3 hp and upBig raised-panel bits, long production runs

Set the bit height and fence

Accuracy comes from the setup, not from rushing the cut. Install the bit so the shank sits well inside the collet, with a small gap left between the bit's cutting section and the collet, then tighten with both wrenches or the spindle lock.

Raise the bit slowly and set the height against a scrap piece of the same thickness as your workpiece. Make a test cut, check the profile, and adjust in small steps. Repeat until the cut matches what you want.

  • Unplug the router and install the bit securely.
  • Set the height using a ruler, a height gauge, or a profile template.
  • Align the fence so the bit's cutting edge sits where you want the cut.
  • Clamp the fence at both ends and check that it cannot shift.
  • Close the fence opening around the bit to reduce the gap where small pieces could catch.
  • Make a test cut on scrap and measure it before touching your good wood.

Feed direction and how to make the cut

Feed direction is the most important habit to learn. The bit spins counterclockwise when viewed from above, so you push the wood from right to left across the table, with the fence on the far side. This brings the cutter against the wood and keeps the workpiece pressed against the fence.

Feeding the wrong way, called a climb cut, can grab the wood and pull it out of your hands. Avoid it on ordinary cuts.

  • Start the router and let it reach full speed before the wood touches the bit.
  • Hold the wood flat on the table and snug against the fence.
  • Feed at a steady pace. Burn marks mean you are going too slowly or the bit is dull. Chatter or tear-out can mean you are going too fast.
  • Keep your hands on the sides and top of the workpiece, away from the bit opening.
  • Let the bit stop spinning completely before reaching near it or clearing chips.

Take light passes and handle tricky cuts

For deep profiles, do not remove everything in one pass. Make two or three shallow passes, raising the bit a little each time. This reduces strain on the router, gives a cleaner surface, and lowers the chance of kickback.

Cut end grain first when you are shaping all four edges of a board, then do the long grain edges. Any small blowout at the end of the cut gets removed by the next pass.

Small or narrow parts are risky to hold by hand. Use a push block with a good grip, a featherboard to hold the wood against the fence, and a miter gauge or sled for short pieces. If a part is too small to hold safely, shape a longer board and cut the part off afterward.

Common mistakes to avoid

Most router table problems come from a few repeated errors. Skipping the test cut is the biggest one, since a wrong height or fence position often ruins good stock. Another is running a large bit at full speed. Large-diameter bits should be run at a slower speed, as the bit maker recommends.

Also watch for a loose fence, a worn or dirty bit, and a dusty table that makes the wood drag. Clean the bit and table now and then, and replace bits that are chipped or dull. A sharp bit cuts cleaner and needs less force.

Looking for a network router instead?

Some readers land here while searching for a different kind of router. If you meant the home internet device, our best router comparison lines up WiFi generation, coverage, and wired port speeds side by side. That page covers networking gear only and does not include woodworking tools.

If you are shopping for a woodworking router, use the size guide above and match the power and collet size to the bits you plan to run. If you also need a new WiFi router for your shop or garage, the router comparison page is the place to start.

Frequently asked questions

Do I need a special router for a router table?

Not always. Many fixed-base routers can be mounted under a table. It helps to have above-table height adjustment, variable speed, and a collet that accepts larger bits. Check the manual to confirm your model can be used in a table.

Can I use a router table without a fence?

Yes, but only for edge cuts that use a bit with a bearing, and you should use a starter pin or pivot point to ease the wood into the bit. For most other cuts, a fence gives much better control.

Why does my wood burn when routing?

Burning usually comes from a dull bit, a feed rate that is too slow, or a bit speed that is too high for its size. Clean or replace the bit and keep a steady feed.

Is a featherboard really necessary?

It is not required for every cut, but it keeps the wood tight to the table or fence and keeps your hands farther from the bit. It is especially helpful on long pieces and repeat cuts.

Compare the products