How to Set Plunge Router Depth and Make Plunge Cuts
To set plunge router depth, unplug the tool, lower the bit until it touches the workpiece, lock it, zero the depth scale, then set the depth stop rod to the cut depth you want. To make a plunge cut, start the motor with the bit raised, let it reach full speed, lower it smoothly to the stop, and feed the router along your line. Take deep cuts in several shallow passes, and test the setup on scrap first.
What a plunge cut is and why depth setup matters
A plunge router lets you lower a spinning bit into the wood while the motor runs. That is how you cut mortises, stopped grooves, inlay pockets and sink holes in the middle of a board, where a fixed-base router cannot start.
Because the bit enters the wood from above, the depth stop is your safety limit and your accuracy tool at the same time. If it slips or is set wrong, the cut ends up too deep or too shallow every time. Spending a few minutes on setup saves a lot of ruined stock.
If you are still choosing a tool, our best plunge router comparison lists power, weight, speed range and depth control side by side.
Set the depth step by step
The exact controls differ by model, but nearly all plunge routers follow the same logic: find zero, then measure up from it. Always work with the router unplugged, or with the battery removed on a cordless model, until the bit is installed and the depth is set.
- Unplug the router. Fit the bit into the collet and tighten it with the wrench. Make sure the shank size matches the collet, since collet size decides which bits fit.
- Set the router on a flat surface, such as the workpiece itself. Release the plunge lock so the motor can drop.
- Lower the motor until the tip of the bit just touches the surface. Lock the plunge in that position.
- Bring the depth stop rod down until it rests on the stop surface, and set the depth scale or indicator to zero.
- Release the plunge lock and let the motor rise. Raise the depth stop rod by the depth you want, using the scale. Check it with a ruler or a set of calipers against the bit.
- Make a test cut in a scrap piece of the same thickness and measure the result. Adjust the stop and cut again if needed.
Scales on router bodies can be a little loose, so trust the test cut over the printed numbers. If you need a repeatable result for several parts, note the stop setting or mark the scrap piece so you can return to it.
Use depth stops, turrets and fine adjusters
Most plunge routers offer more than a plain rod. Knowing what yours has makes multiple passes much easier. Our spec data shows several different approaches, summarized below.
Fine adjusters matter for inlays and joinery, where a small error shows. Steps in small, repeatable amounts let you sneak up on a fit instead of guessing.
| Model | Depth control listed | Notes |
|---|---|---|
| DEWALT DW618PKB | Micro-fine ring, 1/64-inch increments | Ring adjusts depth in small steps |
| Triton TRA001 | Micro winder, continuous fine depth in plunge | Fine adjustment through the plunge range |
| Bosch GOF13-25 | Integrated depth stop, 8-stop increments | Suited to multiple passes |
| DEWALT DCW620B | Tool-free depth system, 3-position adjustable turret stop | Cordless; battery sold separately |
| WORKPRO W125226AE | Rack and pinion depth adjustment knob | Fixed and plunge bases |
| Bosch 1617EVSPK | Microfine bit-depth adjustment | Fixed and plunge bases |
How deep will a plunge router go?
It depends on the model and the bit. The limit is set by the travel of the plunge base and by how long the bit is. Many listings do not publish plunge travel at all, so check the manual or ask the maker if the number matters for your project.
One example from our data is the VEVOR M1DP-XT-10 palm kit. It lists 0 to 0.79 in of depth with the fixed base and 0 to 1.39 in with the plunge base. That shows how the plunge base can reach deeper than the fixed base on the same router.
Even if a router can reach a given depth, you should not cut that deep in one pass. Power matters here. Among the models that list watts in our lineup, 2400 W is the highest and 600 W is the lowest. A stronger motor holds speed better in a deep cut, but shallow passes are still better for every machine.
Make the plunge cut
Once the depth is set, the cut itself is a rhythm: position, start, plunge, travel, retract. Clamp the workpiece so both hands stay on the router handles. Mark the start and end of the cut clearly, and use a fence, straight guide or template if the line must be exact.
Set the speed dial for the bit. Larger bits need a slower speed, and small bits can run faster. Variable speed models, such as the Bosch 1617EVSPK with its 8,000 to 25,000 RPM dial, make this easy to adjust.
- Rest the base on the workpiece with the bit raised and above your start mark.
- Switch on the motor and wait until it reaches full speed. A soft start helps here by easing the motor up gently.
- Release the plunge lock and lower the bit steadily until the depth stop meets its limit.
- Lock the plunge if your router has a lock lever, then move the router along your line at a steady pace. Feed against the bit rotation so it cuts rather than grabs.
- At the end of the cut, release the lock, raise the bit fully out of the wood and only then switch off the motor.
- Wait for the bit to stop spinning before setting the router down.
Cut deep grooves in several passes
For a deep mortise or groove, make a series of shallow cuts and lower the stop a little each time. This keeps the motor from bogging down, leaves a cleaner wall and reduces the chance of the bit grabbing or burning the wood.
A turret stop is built for this. You set the final depth on the lowest step, then work down through the higher steps one pass at a time. A stop with several positions, like the eight-stop setup on the Bosch GOF13-25, serves the same purpose.
If your router has no turret, simply lower the rod in small steps between passes. Fine adjusters such as the DEWALT micro-fine ring make that quick. For final trimming of a pocket floor, use a very light last pass to leave a smooth bottom.
Safety and bit choice
Routers are loud and throw chips fast. Wear safety glasses or a face shield, and hearing protection. A dust mask helps too, because routing makes fine dust. Keep your hands clear of the bit path, and never reach under the base while the motor is running.
Unplug the router, or remove the battery, before every bit change or depth adjustment that involves the collet. Keep the cord behind you and away from the cut line.
A sharp bit of good quality gives cleaner results and needs less force. If you need more bits for mortises and grooves, our best router bit set page can help. For a broader look at the tool itself, including fixed-base models, see our best router comparison.
Frequently asked questions
Why does my plunge router cut deeper than the scale says?
The scale may not have been zeroed against the actual bit, or the bit may have slipped in the collet. Re-zero with the bit touching the surface, tighten the collet firmly and confirm the result with a test cut.
Can I leave the plunge lock on while I cut?
Yes, on most routers you lock the plunge once you reach depth so the router holds its position. Release the lock to raise the bit at the end of the cut, before you lift the tool.
Do I need a plunge base for edge work?
No. A fixed base is fine for edge profiles and trimming. A plunge base is the one to use for cuts that start away from an edge, and every model in our lineup lists both base types.
What speed should I use for large bits?
Use a slower speed for larger bits and a faster speed for small ones. Check the bit maker's guidance, then adjust on a scrap piece if you see burning or chatter.
Bosch 1617EVSPKBest overall
WORKPRO W125226AELight kit with extra guides
DEWALT DCW620BCordless plunge option