How to Router a Circle in Wood
The easiest way to router a circle in wood is to pivot the router on a trammel arm, which is a simple jig that fixes the bit at a set distance from a center pin. Set the radius, cut in several shallow passes, and move the router counterclockwise around the center. For repeat circles or tight tolerances, a template and a bearing-guided bit is a good second option.
What You Need
Circle routing works with almost any handheld router that has a plunge base or an easily adjusted fixed base. You do not need much more than a few common shop items.
A straight bit is the usual choice for cutting through the wood. A spiral upcut or downcut bit leaves a cleaner edge than a basic straight bit, but either will do the job if it is sharp. If you are shopping for a router for this kind of work, our best router wood page compares models side by side using published specifications.
- A router with a collet that grips the bit firmly
- A sharp straight or spiral bit sized for your cut
- A trammel arm or a plywood circle jig
- A small screw or pin for the pivot point
- Clamps and a sacrificial board to protect your bench
- Safety glasses, hearing protection, and a dust mask
Method 1: The Trammel Jig
A trammel is a straight strip, often a scrap of plywood or hardboard, with the router fixed at one end and a pivot pin at the other. The distance from the pin to the edge of the bit equals the radius of your circle. This is the most common method because it is cheap and accurate.
Many routers come with a trammel rod or have an accessory available. If yours does not, a shop-made arm works just as well. Fasten the router base to the arm with screws through the base's mounting holes, and make sure nothing can shift during the cut.
- Mark the center of the circle on your workpiece.
- Decide which side you are keeping. For an outside edge, the bit cuts outside the circle line. For a disk you are keeping, measure from the pin to the outer edge of the bit.
- Set the radius by measuring from the pivot pin to the bit's cutting edge, not to the center of the bit.
- Place the pin in a small hole at the marked center. Put the workpiece on a sacrificial board so the bit can cut through cleanly.
- Set a shallow first pass, switch on the router, and move it counterclockwise around the pivot.
- Lower the bit in small steps and repeat until you cut all the way through.
Method 2: Template and Bearing Bit
If you need several identical circles, or you already own a round template, a flush-trim or pattern bit is a better fit. The bit has a bearing that rides along the template while the cutter shapes the wood to match.
First, rough cut the workpiece slightly oversize with a jigsaw or band saw. Then attach the template on top with double-sided tape or clamps, and run the bearing around the edge. The router follows the template, so the final shape depends on how clean your template is. Sand the template edge smooth before you start.
This method is great for repeat work but needs a quality template. A trammel is better when you need a custom size once.
Which Method Should You Choose?
Both methods give good results. The table below shows where each one fits best.
| Factor | Trammel jig | Template with bearing bit |
|---|---|---|
| Best for | One-off circles of any size | Repeat circles of one size |
| Setup effort | Measure and set the radius | Make or buy a template first |
| Flexibility | Easy to change the diameter | Fixed to the template size |
| Rough cutting needed | No | Yes, cut oversize first |
| Edge quality | Clean if passes are shallow | Clean if template edge is smooth |
Depth and Feed Direction
Do not try to cut through in one pass. Take shallow passes, a little at a time, and increase the depth gradually. Deep cuts strain the bit, burn the wood, and make the router harder to control. In hardwood, use smaller steps than you would in softwood.
Feed direction matters. A router bit spins clockwise when seen from above, so you want to push the tool against that rotation. With a trammel, that means traveling counterclockwise around the center. Moving the other way can make the router grab and pull itself forward, which is a safety risk and gives a rough edge.
Keep a steady pace. If you hear the motor bog down, slow your feed or reduce the depth. If the wood shows burn marks, you are likely moving too slowly or the bit is dull.
Safety Notes
A router is loud and throws chips, so wear eye and hearing protection every time. A dust mask is wise, since routing creates fine dust.
Unplug the router before you change bits or adjust the collet. Make sure the bit is seated properly in the collet and tightened according to the maker's directions. Never let the bit touch the wood when you switch the router on.
Clamp the workpiece so it cannot move, and keep your hands clear of the path of the bit. Hold the router with both hands. When the cut finishes, let the bit stop spinning before you lift the tool away. As the disk is cut free, it can shift or bind against the bit, so support it or leave a small tab and trim it off afterward.
Finishing the Edge
After the final pass, the edge may have small ridges or slight burn marks. Sand it lightly with fine paper wrapped around a curved block to keep the circle round.
If you want a softened edge, you can follow up with a roundover bit. Run it counterclockwise around the outside edge in the same manner, keeping your passes light. For ideas on the type of router that suits this kind of edge work, see our best router wood comparison.
Frequently asked questions
Can I cut a circle without a trammel?
Yes. A plywood base with a pivot hole works like a trammel, and a template with a bearing bit needs no pivot at all. A jigsaw cut followed by sanding also works for rough shapes.
Why is my circle not perfectly round?
Common causes are a pivot pin that wobbles in its hole, a trammel arm that flexes, or taking passes that are too deep. Tighten the setup and take lighter cuts.
Can I cut an inside circle, such as a hole?
Yes. Use the same trammel setup, but measure the radius to the inside edge of the hole. The feed direction reverses for inside cuts, so check your router's rotation and push against it.
What should I do about tear-out on plywood?
Use a sharp bit, a sacrificial backer board, and light final passes. A downcut spiral bit can help on the top face, while an upcut helps on the bottom.
NETGEAR RS700S-100NASBest overall
ASUS GT-BE98Highest combined speed
TP-Link Archer BE400Fastest 5 GHz band