Guide

How to Cut Wood Using a Router: Straight Cuts, Shapes, Letters and Signs

Yes, a router can cut wood. Clamp a straight edge or template to the workpiece, fit a straight or flush trim bit, and remove the wood in several shallow passes instead of one deep cut. A router is slower and fussier than a saw for plain cutting, but it excels at cutting out shapes, grooves, letters and signs.

Updated 2026-11-12 · Based on published specifications and maker information

Top picks from our best router wood comparison

What a router does well (and what it doesn't)

A router spins a bit at high speed and shaves wood away a little at a time. That makes it great for repeatable shapes, clean edges and carved details. It is not the fastest way to cut a board to length. A saw does that job with less setup and less dust.

So think of the router as a shaping tool that can also cut through thin stock when you need an exact outline. If you are still choosing a tool, our best router page compares published specifications, and best router wood covers routers aimed at woodworking.

Gear and setup before you start

Good results come from preparation. Most bad cuts trace back to a loose workpiece, a dull bit or a guide that shifted mid-pass.

Gather these items first:

  • A router with a collet that matches your bit shank size
  • A sharp bit suited to the job (see the table below)
  • Clamps to hold the workpiece firmly to a bench
  • A straight edge, jig or template, clamped down
  • A sacrificial board under the workpiece so the bit does not cut your bench
  • Safety glasses, hearing protection and a dust mask

Cutting wood in a straight line or through-cut

For a straight cut, use a straight bit and a guide. Many routers include an edge guide, or you can clamp a straight board to the workpiece as a fence. Measure the distance from the bit's edge to the edge of the router base, then set the fence at that offset so the bit lands on your line.

Follow these steps:

  • Mark your cut line and clamp the workpiece securely.
  • Install the bit so the shank is fully seated in the collet, then back it out slightly as the manual directs.
  • Set a shallow depth. Plan several passes rather than one deep one.
  • Rest the router base on the wood with the bit clear of the surface, then switch it on and let it reach full speed.
  • Move the router steadily against the bit's rotation, keeping the base pressed against the fence.
  • Lower the depth a little and repeat until the bit cuts through into the sacrificial board.
  • Switch off and wait for the bit to stop spinning before you lift the router.

How to cut out shapes with a router

For curves, circles and custom outlines, a template is the key. Cut or print your shape on thin plywood or hardboard, sand its edge smooth, and fasten it to your workpiece with clamps or double-sided tape. A flush trim bit has a bearing that rides along the template while the cutters trim the wood to match.

The usual method is to rough out the shape first with a jigsaw or bandsaw, leaving a small margin outside the line. Then the router only has to remove a thin layer, which gives a cleaner edge and puts less strain on the bit.

For perfect circles, a trammel or circle jig pivots the router around a center point. Set the radius, make a shallow pass, then deepen the cut a bit at a time until you are through. Keep the offcut supported so it does not drop and pinch the bit as you finish.

How to router letters and wood signs

Routed lettering is usually carved into the surface rather than cut through. A V-groove bit gives crisp, angled letter walls, and a small round-nose bit gives softer, rounded grooves. Both work well on signs.

To keep the lettering sharp:

Print or trace your design at full size, then transfer it to the board. Letter templates and guide bushings help beginners follow the outline, since freehand routing demands a very steady hand. Practice on scrap of the same wood first so you can judge depth and speed.

Work in small, controlled passes. Rout the inside details first, such as the centers of letters, then the outer strokes. Routing across the grain can tear the edges, so a light first pass and a sharp bit matter. Finish by sanding lightly and sealing the sign if it will live outdoors.

For a bigger piece, routing out the background around raised letters is another option. That takes more passes, but it makes the lettering stand proud of the surface.

Which bit for which job

Choosing the right bit saves time and frustration. This table sums up the common choices for cutting tasks.

JobBit typeNotes
Straight cut or grooveStraight bitUse with a fence or edge guide
Matching a templateFlush trim or pattern bitBearing follows the template
Clearing out a recessStraight or spiral bitMake several shallow passes
Sharp letteringV-groove bitGood for signs
Soft rounded letteringRound-nose bitGentler look inside grooves

Safety notes

Routers are loud, fast and throw chips, so protection is not optional. Wear safety glasses and hearing protection every time, and a dust mask or extraction since fine wood dust is bad for your lungs.

Always unplug the router, or remove the battery, before changing bits or adjusting depth. Keep both hands on the handles, keep the cord clear of the bit's path, and never start the router with the bit touching the wood. Clamp the work so your hands never need to hold it near the cutter, and keep loose sleeves and long hair away from the tool.

Frequently asked questions

Can a router replace a saw?

Not really. A router can cut through thin boards, but it is slower and needs jigs for accuracy. Use a saw for rough cuts and a router for precision outlines and details.

Which direction should I move the router?

Feed the router against the rotation of the bit. On the outside edge of a workpiece that usually means moving left to right. Check your manual, since feeding the wrong way can make the router grab and run away.

Why is my routed edge splintering?

Common causes are a dull bit, cutting too deep in one pass, or feeding too fast. Take lighter passes, replace worn bits, and back the workpiece with scrap where the bit exits.

Do I need a router table?

No. A handheld router with clamps, guides and templates handles most cutting, shaping and sign work. A table helps with small pieces and repeat edge profiles.

Compare the products