Can You Use a Stud Finder on Plaster, Brick, or Tile?
Yes on plaster, tile and popcorn ceilings, if the finder reaches deep enough and you scan slowly. No on solid brick, where there are no studs to find, and stucco is only workable from the inside. Thick or uneven surfaces call for a deeper-reading tool and a few backup checks.
How a stud finder reads a wall
An electronic stud finder senses changes in density behind a surface. When it passes over a stud, joist or metal framing, the reading changes and the display lights up. The thicker or more uneven the surface, the weaker that signal gets.
That is why the surface matters more than the material name. Smooth drywall is the easy case. Plaster, tile, texture and masonry all add thickness, density or bumps that can blur the reading or fool the sensor.
Two specs on a product listing help most here: maximum detection depth and the number of sensors. Our best stud finder comparison lists both side by side, so you can match a tool to a harder wall.
Plaster walls
Plaster is the most common trouble spot. In older homes, plaster is often applied over wood lath, which is thin strips of wood with gaps between them. The surface is thick, uneven and inconsistent in density, so a stud finder can give false positives.
Most standard finders can work on thin plaster, but results vary. A deeper reading range helps. Among the products on our spec sheet, the Franklin ProSensor MAX lists 2.5 in of depth and a second mode for deep scanning. Its listing says it scans through two or more layers of drywall, plaster, OSB, plywood and MDF. Several other models list 1.5 in to 1.7 in, and two list only 0.75 in, which is a poor fit for thick plaster.
Try this routine on plaster:
- Scan in several horizontal passes at different heights, not just one.
- Mark every hit, then look for marks that line up vertically.
- Studs are usually spaced 16 in or 24 in apart, so marks that fit that pattern are more believable.
- Confirm with a magnet or a small finish nail in an inconspicuous spot. Lath is nailed to studs, so you may find a line of nails.
- Treat any single, isolated reading as unconfirmed.
Tile
Tile alone is rarely the problem. Behind it sits adhesive, a layer of backer board or mortar, and sometimes metal mesh. Together these can add enough thickness to push past what a basic finder can read.
If you need a stud behind a tiled bathroom wall for a grab bar or a shelf, start by scanning a nearby untiled wall. Studs usually continue at the same spacing, so you can measure over. Then use a finder with a deeper mode to check the tile itself. The ProSensor MAX listing mentions large tile among the surfaces it can scan through. Grout lines and small mosaic tiles make the surface bumpy, so slide the tool slowly and keep it flat.
Also remember that bathrooms hold pipes. A stud finder does not reliably find water lines, so drill with care and check where plumbing runs on the other side of the wall.
Brick, stucco and other masonry
Solid brick, concrete and block walls do not have studs, so there is nothing for a stud finder to locate. If you are hanging something on one of these walls, the job is about choosing the right anchor, not finding a stud. Look at the mortar joints and the brick faces and pick masonry anchors that suit the weight.
Brick walls that have been furred out with wood strips and covered in drywall or plaster are a different case. A stud finder may find the strips, which are not structural studs but can hold light loads.
Stucco is a thick cement-based coating, often over wire mesh, and it is usually on an exterior wall. Metal mesh and thickness make electronic scanning unreliable. The easier method is to find the framing from inside the house, then measure through the wall to the matching spot outside. Check that the location is clear of wiring and pipes before you drill.
Popcorn and textured ceilings
Texture lifts the tool off the surface. The finder then reads a gap, and the sensors may not see the joist at all. Run the tool slowly and keep firm, even contact. Some people slip a thin, smooth card or a piece of cardboard under the tool to help it glide, though that adds a little thickness.
Ceiling joists often run in one direction, so scan across them, not along them. Mark the edges you find, then check the spacing. If the readings look random, move to a spot that is not heavily textured, such as near a wall or a light fixture, and measure from there.
Older popcorn ceilings, especially in homes built before the 1980s, may contain asbestos. Do not scrape, sand or drill into a ceiling like that until it has been tested.
Choosing a finder for hard surfaces
Use the specs on our comparison page to narrow the field. Here is how a few relevant models compare, based on the published data.
Wire detection is a useful bonus on any surface. The ProSensor M210 and M150 list it, but the ProSensor MAX does not. That is a tradeoff to weigh if you want deep scanning and a live wire alert in one tool.
| Model | Max depth | Sensors | Live wire detection |
|---|---|---|---|
| Franklin ProSensor MAX | 2.5 in | 13 | Not listed |
| Franklin ProSensor M210 | 1.7 in | 13 | Yes |
| Franklin ProSensor 710+ | 1.6 in | 13 | Not listed |
| Franklin ProSensor M150 | 1.5 in | 9 | Yes |
| Franklin ProSensor M70 | 1.5 in | 7 | Not listed |
Safety before you drill
Finding a stud is only half the job. Wires and pipes can run through or beside framing, and a finder is not a guarantee that a spot is clear.
Follow these steps every time:
- Turn off power at the breaker for the circuit near your work area, even if your finder detects live wires.
- Wear safety glasses when drilling, and more so overhead, where dust and debris fall toward your face.
- Use hearing protection and a dust mask when drilling into masonry, tile or plaster.
- Keep both feet steady on a stable ladder when working on ceilings.
- Drill a small pilot hole first, and stop if you feel unexpected resistance or see metal.
Frequently asked questions
Can a magnet find studs in plaster?
A strong magnet can find the nails or screws that hold lath or drywall to the framing. Slide it over the wall until it grabs. A line of hits usually follows a stud.
Why does my stud finder beep everywhere on plaster?
Uneven thickness, lath gaps and metal in the wall can all trigger readings. Try recalibrating if your tool needs it, then scan at several heights and keep only marks that line up vertically.
Do I need a stud for every shelf or mount?
Not always. Light items can go on the right wall anchor. Heavy loads such as a TV mount should go into studs or joists, or into masonry with the correct anchors.
Does a deeper reading range make a finder better on all walls?
Not by itself. It helps on thick plaster, tile or double layers. On plain drywall, a shallower tool that shows the full stud width can be just as useful.
Franklin Sensors 317740851Best overall
Franklin Sensors ProSensor M155Wire alert, compact body
Franklin Sensors MAX12Deepest scan in lineup