Best Miter Saws in 2027

That means the blade tilts both ways and the head slides on rails. This combination suits general woodworking and framing, because you can cut wide boards and angled joints without flipping the workpiece. The data does not give a max crosscut width in in.

The listing says it crosscuts a 2 × 12 at 90 degrees and a 2 × 8 at 45 degrees. It has 11 positive stops, which are preset detents that let you lock common miter angles quickly and repeat them. The miter range runs up to 50 degrees left and right. Its max left bevel is 48°, which ties the highest value on the page.

The 15 amp motor turns at 4,800 RPM. An LED shadow line shows where the blade will cut, so you can line it up with a pencil mark. The saw weighs 39.4 lb and is corded, so it needs an outlet. Dust collection is not listed in the data, so check that if cleanup matters to you.

Its crosscut width is 14 in, the highest of all 16 products on the page. For framing and wide shelving boards, that extra width means fewer boards you cannot cut in one pass. It is also cordless, which suits work away from an outlet.

The listing says it cuts 6-1/2 in baseboard standing up and 6-1/2 in crown nested. It uses a cutline blade positioning system for adjustment-free cut line indication. The data does not list positive stops, bevel angle or an LED light, so check those before you buy. Dual bevel means the blade tilts either way, saving board flips.

At 51.7 lb it is not light for a portable saw, and the battery is a factor. The listing says it works with the 20V MAX and FLEXVOLT battery range. It claims up to 371 cuts in 3 1/4 in MDF base molding. Dust collection captures up to 97% of dust per the listing, and a vacuum can start with the trigger.

The data does not list a sliding rail, crosscut width, positive stops or bevel angle, so those answers must come from the maker.

The listing describes a 15 amp, 1100 watt motor turning at 3,800 rpm, built for heavy duty use. For accuracy, it uses an integrated cutline blade positioning system. That gives an adjustment-free cut line indication. It also has XPS LED shadow line technology, which projects a shadow of the blade onto the board so you can line up a mark precisely.

At 54.67 lb it is heavier than the Skil and the other DEWALT corded models in this top five, so moving it between jobs takes more effort. It is corded and not a sliding saw per the data. The listing says its dust collection captures over 75% of dust generated. That helps in a shop where cleanup matters.

That makes it a close sibling of the DWS715, but with the ability to tilt the blade both directions. For trim and framing angles, that saves you from flipping the board and reduces setup mistakes.

Accuracy features stand out. It has 14 positive stops, tied for the most on the page, on a stainless steel detent plate. The listing says the miter range is 0 to 50 degrees left and right. Bevel positive stops sit at 0, 22.5, 33.9 and 45 degrees, and max left bevel is 48°, tied for highest.

The tall sliding fences support nested crown molding up to 6-5/8 in and base molding up to 6-1/2 in vertically. It weighs 50.35 lb, so it is a shop or truck saw more than a carry-anywhere tool. The data does not list a rail slide, an LED light or a crosscut width in in. Dust collection is listed.

The DEWALT DWS715 ranks fourth on our Best Score at 60. Single bevel means the blade tilts one way, so some angled cuts need you to flip the board. In return, it weighs 36 lb, much less than the dual bevel DEWALT 12 in models in this top five.

It has 14 positive stops, which ties the highest on the page. A stainless-steel detent plate holds those angles, so repeat cuts come out the same. Max left bevel is 48°, also tied for highest. The listing says it bevels 0 to 3 degrees to the right, which is limited. It is not a sliding saw in the data.

The listing gives lumber capacity of 2 × 8 at 90 degrees and 2 × 6 at 45 degrees. That is smaller than the Skil's 2 × 12 claim, so wide framing boards may not fit. The tall sliding fence supports 5-1/2 in base vertically. The data lists dust collection, but not an LED light or a crosscut width in in.