Best Gear Pullers in 2027

This Orion Motor Tech set leads our ranking. It includes four pullers with maximum spreads of 3 in, 4 in, 6 in and 8 in. That range handles small pulleys and larger gears alike. Four sizes means you can match the puller to the part. Each puller turns with a wrench or ratchet, so you do not need a hydraulic setup.

Reach matters when a part sits deep on a shaft. The largest puller reaches 9.2 in, the longest reach among the models that list it. The jaws are reversible, so you can pull from the inside or the outside. The 6 in and 8 in sizes have dual fixing holes for four setups. The maker lists three jaws, which spread the force evenly across the part.

The build is carbon steel, drop-forged and heat-treated according to the listing. The set weighs 10 lb. The maker does not publish a ton rating, so check the job before you pull a stuck part. For heavy industrial pulling, a hydraulic model is a better match.

This VEVOR YL-15T ranks second on our spec sheet. It is hydraulic and rated at 15 ton, tied for the highest capacity here. Hydraulic force does the work instead of your arm. That suits seized bearings, hubs and large gears that a hand-driven screw puller may not move. You can work it horizontally or vertically, which helps on parts that face different directions.

Max spread is 12 in, tied for the widest here. A 12 in spread opens the door to wide pulleys and flanges. You can run two jaws or three jaws, and the jaws are reversible. Two jaws suit small bearings. Three jaws spread the load on large parts. The maker does not publish max reach, so check clearance on deep shafts before you buy.

It weighs 25 lb, the heaviest in the lineup, so expect a bench or shop job rather than a toolbox carry. A storage case is included, along with an extended handle. The body is industrial-grade steel with a rust-resistant coating. It may be more tool than a home garage needs.

Third in our ranking, this VEVOR matches the 15 ton hydraulic rating of the model above it. It also shares the 12 in maximum spread. The difference is the body. It weighs 17 lb, lighter than the YL-15T, so it is easier to carry to the job. A hydraulic ram also helps with seized hubs, flanges and pulleys.

This listing publishes reach and spread range, which the other VEVOR does not. Max reach is 7 in. The adjustable spread runs from 3.9 in to 11.8 in, so it can grip fairly small parts as well as wide ones. A wider range means more flexibility across different parts. Jaws work in two or three jaw layouts.

The listing mentions forged steel, a pump head that rotates 360 degrees and a relief valve. It is sold as one piece, and no case is listed. Reach of 7 in is shorter than the 9.2 in on the Orion set, so deep shaft work may call for a different puller. Check the clearance around your part before you buy.

Fourth in our ranking, this CARVALAX kit is built for breadth. It has 13 pieces, the most on the page, in a storage case. The kit holds a 2T puller and a 5T puller, plus three extra-long 5T jaws. Those jaws extend the 5T spread to 8 in. Having two sizes means you can match the puller to small pulleys or larger gears.

Spread-locking balls on the jaws hold the opening where you set it. That works much like a ratchet and saves fiddling when you line up a part. Jaws are reversible for internal or external pulling, and you can switch between two jaw and three jaw setups. The listing says tapered jaws keep a grip on rounded pulleys and rusted sprockets. Max reach is 7.75 in.

The steel is heat-treated chromium vanadium. At 7.12 lb, it is the lightest among the models that list weight. It tops out at a 5T rating, so it will not replace a 15 ton hydraulic unit for very large, seized parts. Pick it for versatility, not for raw force.

This DURATECH ranks fifth, and it suits a narrower job than the others. It is a mechanical screw puller rated at 3 ton. You turn the screw with a wrench, ratchet or spanner. That keeps it simple, but it has less capacity than the other models that list it. Its 3 jaw layout spreads the pulling force across the part.

Size is the main limit. Max spread is 3 in, the lowest on the page, and max reach is 3.56 in, also the lowest among the models that list it. Choose it for small gears, pulleys and bearings on a shaft. Wide hubs and deep parts will not fit. Check your part's diameter against 3 in before you order.

The three jaws are chrome vanadium steel, drop-forged and heat-treated. Each jaw can be flipped to pull from the inside or outside. Still, the jaws are interchangeable for different shapes. The maker does not publish weight, a case or a kit count. For a general best gear puller pick, this is a small specialty tool, not an all-round answer.