Guide

Why Does My Submersible Well Pump Not Work? Causes and Fixes

Most submersible well pump problems come from the power supply, the pressure switch, the pressure tank, or a pump that has lost water or a prime. Start at the breaker and the pressure switch, because they are the easiest to check and the most common culprits. If the power and controls look fine and the pump still will not deliver water, the pump, its control box or the wiring down the well is probably at fault, and that is a job for a licensed well professional.

Updated 2026-11-12 · Based on published specifications and maker information

Top picks from our best well pumps submersible comparison

Start with the quick checks

A submersible pump sits deep in the well, so you cannot see it. That means you work from the surface down: power, controls, pressure, and only then the pump itself. Many "dead pump" calls end at the first or second step.

Before you touch anything electrical, switch off the breaker for the pump circuit. Well pumps usually run on 230V, and even 115V models can cause a serious shock when wiring is wet or damaged. Never work on live wiring, and never stand in water while testing anything.

  • Check the breaker. A well pump often uses a double-pole breaker. If it has tripped, reset it once. If it trips again right away, stop and call a professional.
  • Look for a separate well switch or disconnect near the pressure tank and confirm it is on.
  • Read the pressure gauge near the tank. Zero pressure with a silent pump points to power or switch trouble.
  • Listen at the pressure switch and control box. A click with no hum can mean a failed relay or capacitor.
  • Ask whether the whole house lost power, or whether a recent storm or outage came before the problem.

The pump does not run at all

If the breaker is on and the pump stays silent, the cause is usually the pressure switch, the control box, or the wiring. The pressure switch is the part that tells the pump to start when tank pressure drops. Burned or pitted contacts, or a clogged sensing port, can stop it from closing the circuit. Our well pump pressure switch comparison shows the pressure ranges and ratings to look for if yours needs replacing.

Control boxes matter too. Some pumps use an external control box that holds the start capacitor. The VEVOR 3 HP 230V pump on our list, for example, ships with an external control box. Other pumps build the capacitor into the motor, so there is no box to fail. The Hallmark 1 HP 230V (MA0414X-7A) lists a built-in capacitor start and no control box requirement, and the Wassermann 4STM4 is a 2-wire pump with a built-in control box. Check your pump's label to learn which type you have before you start tracing wires.

Thermal protection is another possibility. Some pumps, including the VEVOR 3 HP and the Holdwell 1 HP, list built-in overload or overheat protection that shuts the motor off when it stalls or runs hot. If the motor tripped out, it may restart after it cools, but you still need to find out why it overheated.

The pump runs but little or no water comes out

A humming pump with weak or no flow can have several causes. The water level in the well may have dropped below the pump intake. Submersible pumps are not meant to run dry, and the VEVOR and Holdwell listings both warn against running without water or at very low water levels. If you suspect a low well, shut the pump off and have the water level checked.

A failed check valve is another common cause. A check valve holds water in the pipe so it does not drain back down the well when the pump stops. If it fails, the pump has to refill the line every cycle, pressure drops quickly, and the pump runs more than it should. Many pumps include a built-in check valve, but the VEVOR and Holdwell listings both recommend adding another one in the line.

Clogs and worn parts also reduce flow. Sand and sediment can block the intake screen or wear the impellers. Both of those listings suggest a layer of gauze in front of the intake for newly drilled wells with a lot of sediment. A leak in the drop pipe or a split fitting can also send water back into the well instead of up to the house.

The pump turns on and off too often

Rapid cycling is hard on the motor. The usual cause is a waterlogged pressure tank, meaning the air cushion inside has been lost. With less air, the tank fills and empties in seconds, and the pressure switch keeps calling the pump on. Check the tank's air charge with the system depressurized, using a tire gauge on the valve stem. The charge should be a couple of pounds below the switch's cut-in pressure, as stated on the tank label or switch.

A leaking check valve, a leak in the plumbing, or a pressure switch set or built incorrectly can also cause short cycling. If you recently replaced the switch, confirm its cut-in and cut-out settings match your tank and pump. Mismatched settings can make the pump run far too long or far too little.

Match symptoms to likely causes

Use this table as a starting point. It does not replace a proper diagnosis, but it narrows your search.

SymptomLikely causeWhat to check
No sound, no pressureTripped breaker or failed switchBreaker, disconnect, pressure switch contacts
Click or hum, no startBad capacitor or control boxControl box (if your pump has one), wiring
Runs, no waterLow water level or air in the lineWell water level, drop pipe, intake screen
Pressure falls when pump stopsFailed check valveCheck valve at the pump and in the line
Cycles on and off quicklyWaterlogged tankTank air charge, switch settings
Runs then shuts off by itselfOverheating or overload tripMotor protection, water level, voltage

How to tell if a submersible well pump is working

A healthy pump starts when pressure falls to the switch's cut-in point and stops at cut-out. Open a faucet and watch the gauge. Pressure should drop, the pump should start, and pressure should then climb steadily until the pump shuts off.

You can also feel the pipe near the tank. When the pump runs, you may notice a slight vibration, and you may hear a faint hum from the control box if your pump has one. Silence while the gauge reads zero and the faucets are dry means the pump is not receiving power or not responding.

If you have a clamp meter and know how to use it safely, a professional can compare running amperage to the motor's nameplate rating. Amperage far above or below the rating often points to a motor, wiring or water-level problem. Leave this test to someone qualified.

When to call a professional or replace the pump

Call a well professional if the breaker keeps tripping, if you suspect a wiring fault, or if the pump has to be pulled from the well. Pulling a pump is heavy and can be dangerous. Drop pipe, wire and a wet pump add up to a lot of weight, and a dropped pump can be lost in the casing.

If the pump itself has failed, sizing the replacement correctly matters. Total head must cover well depth, the rise to the house and tank pressure, and the voltage must match your circuit. Our submersible well pump comparison lays out head, flow and voltage side by side. For example, the Hallmark 2 HP lists 420 ft of head and 35 GPM, while the Holdwell 1 HP lists 207 ft and 37 GPM on 115V. Have a pro confirm your numbers before you buy.

Frequently asked questions

Can a submersible well pump be reset?

Some pumps shut off from overload protection and restart after cooling, and a tripped breaker can be reset once. If the pump or breaker trips again, there is an underlying fault that needs finding.

Is it harmful to run a submersible pump dry?

Yes. Submersible pumps rely on water for cooling and lubrication, and running them dry or at very low water levels can damage the motor. Turn the pump off if you suspect the well is low.

Can I test the pressure switch myself?

You can look for burned contacts or a clogged port with the power off. Testing the switch live involves line voltage, so use a qualified person if you are not experienced with electrical work.

Why is my water cloudy or sandy before the pump quits?

Sediment can wear impellers and clog the intake screen, which cuts flow. It may point to a worn pump or a well issue, so have a professional take a look.

Compare the products