Why Does My Screwdriver Slip and How Do I Fix It?
A screwdriver usually slips because the tip does not fit the screw head snugly, because you are not pressing down enough, or because the bit or screw is worn. Switch to the exact bit size and type, push firmly in line with the screw, and on a power screwdriver lower the torque setting. Most slipping stops after those three changes.
What is actually happening when a screwdriver slips
Slipping has a name: cam-out. The tip climbs out of the recess in the screw head while you turn, usually because the turning force is pushing the bit up and out faster than your downward pressure holds it in. Each slip rounds off the edges of the recess, so the next attempt slips more easily.
The same causes apply to manual and electric screwdrivers. Electric ones just make the problem faster, since the motor can chew up a screw head in a second or two.
The most common causes
Check this list in order. The first three account for most slipping.
- The bit is the wrong type or size for the screw.
- You are not pressing hard enough along the screw's axis.
- The bit is held at an angle instead of straight in line.
- The torque is set higher than the job needs.
- The bit tip is worn, rounded or dirty.
- The screw head is already stripped or painted over.
- The bit wobbles in the holder because it is loose or poorly seated.
Match the bit to the screw
A bit that looks close is often not close enough. Phillips and Pozidriv screws look alike, but their bits are shaped differently, and using one in the other leaves play in the recess. Size matters too: a bit that is too small rattles in the head and rides up under load.
The bit should sit all the way down in the recess with almost no wobble. If it moves around, try the next size up or down. If you are unsure about the type, test a few bits until one seats fully.
Kits help here because they cover more screw types. Bit counts in the power screwdriver kits we compare run from 5 to 162. Electronics work often needs Torx, Pentalobe and Tri-Wing bits, while furniture mostly needs Phillips, slotted and hex. Our best power screwdriver comparison lists what each kit includes so you can match the bits to your screws.
Pressure, angle and torque
Push firmly toward the screw while you turn. With a manual screwdriver, lean your body weight behind the handle. With a power model, keep the tool in a straight line with the screw and let the bit seat before you pull the trigger or press the button.
Start slowly. A low speed lets the bit bite before the full turning force arrives. Some tools include a soft start for this reason. The DEWALT 4V on our comparison page, for example, lists soft start and lower speed first and second modes for delicate work.
Torque is the other half. Too much torque on a small or soft screw will strip it or crack the part. Adjustable torque settings stop the motor at a set level, which is why they matter on a power screwdriver. The table below shows how the torque options on a few models we compare differ.
| Model | Torque options listed | What it means for slipping |
|---|---|---|
| STREBITO 67-in-1 | 5 levels up to 0.5 Nm powered, up to 7 Nm manual | Low powered torque suits small electronics screws |
| HOTO 25-Piece | Up to 4 N·m electric, up to 8 N·m manual | Smart sensor stops rotation when you release the button |
| DEWALT 4V | 6-stage control, up to 5 N·m powered | Fine steps help match force to the screw |
| Tilswall W122 | 4 levels from 2.6 to 10 N·m | Higher range suits wood, so start on a low level |
Worn bits and damaged screws
Bits wear out. If the tip looks rounded, shiny or chipped, it will not hold the screw well no matter how carefully you work. Replace it. A fresh bit often fixes a slipping problem on its own.
Dirt, paint or drywall dust packed into the recess also stops the bit from seating. Clean it out with a pick or a small flat blade before you start.
If the bit pops out of the holder, check that it is fully pushed in. Magnetic holders and quick-load collets keep bits secure, but a worn holder can still let one wobble.
How to remove a stripped screw
If the head is already rounded, try these steps from easiest to hardest. Wear safety glasses for all of them, because bits can snap and metal can fly.
Clamp or brace the work so it cannot move, and keep your free hand out of the line of the tool. If the screw is in an electrical box or outlet cover, turn off the power at the breaker first.
- Press a wide rubber band or a piece of cloth between the bit and the screw head, then turn slowly with firm pressure.
- Try a slightly larger bit, or hammer a Torx bit gently into the recess to cut new grip.
- Use a screw extractor bit, following the instructions that come with it, and run the tool in reverse at low speed.
- Grip a raised head with locking pliers and turn it out.
- As a last resort, cut a new slot across the head with a rotary tool and use a flat blade.
Choosing a power screwdriver that slips less
If you keep fighting cam-out, a better-matched tool can help. Look for adjustable torque, a manual mode for finishing tight screws, and a bit set that fits your screws. Precision models use low torque to protect tiny screws, while household models offer several N·m for furniture and fixtures.
Our power screwdriver comparison puts torque, speed, battery size and included bits side by side, so you can pick a model that fits the screws you drive most.
Frequently asked questions
Should I finish tight screws by hand?
Yes, it is often a good idea. Run the screw in with the motor, then switch to manual mode or a hand screwdriver for the last turns. You can feel the screw seat and avoid overtightening.
Can I use a drill bit holder or a loose bit in my screwdriver?
Only use bits that fit your tool's holder snugly. A loose bit wobbles, which makes it slip and can damage both the bit and the screw head.
Does a magnetic bit help prevent slipping?
A magnet holds the screw on the tip and makes starting easier, but it does not replace a correct fit. The bit still has to match the recess.
Why does a new screw strip so quickly?
Soft metal screws strip easily, especially with high torque or an ill-fitting bit. Use a lower torque setting, press firmly and drill a pilot hole in hard wood.
STREBITO Best for electronics
STREBITO
HOTO QWLSD011Best everyday kit