Guide

Why Do Cabinet Hinges Keep Breaking or Binding?

Cabinet hinges usually bind or fail because the screws have worked loose, the screw holes are stripped, the door is heavy or misaligned, or the hinge does not match the door. Most problems can be fixed with a screwdriver and a few minutes of adjustment. If the hinge is bent, rusted or has a worn spring or damper, replace it with a model that fits your overlay and existing holes.

Updated 2026-11-13 · Based on published specifications and maker information

Top picks from our best cabinet hinges comparison

What is usually going wrong

Hinges take a lot of small, repeated stress. A kitchen door can open and close many times a day, and every swing pulls on the screws that hold the hinge to the door and the cabinet. Over time, wood screws can loosen, especially in particleboard or chipboard, which crumbles around the threads.

Weight makes it worse. Door racks loaded with bottles or cans, a heavy slab door, or a door that people lean on or pull open by the edge all push the hinge out of line. Once one screw loosens, the others carry more load and the problem spreads.

Fit matters too. A hinge made for one overlay will not behave well on a door that needs another. The wrong overlay can leave gaps or stop the door from shutting. If the hinge never worked well from day one, the fit is a better suspect than wear.

Why hinges bind or stick

Binding means the door resists, scrapes or stops short. The cause is often simple. On older pin style hinges, the pin can rust or collect grime, which makes the joint feel stiff. Cleaning the pin and the knuckle often frees it.

On concealed hinges, binding usually comes from alignment. If the door sags, its lower corner can rub the frame or the door below. If the hinge arms are out of square, the door may catch before it closes fully. A door that has swollen with humidity can also rub on one edge, even when the hinges are fine.

Soft close and spring hinges add one more cause. A damper or spring that has worn out or gotten gummy can make the door drag, stop partway or snap shut. In that case, adjusting will not help and the hinge needs replacing.

Quick diagnosis: symptom, cause and fix

Match what you see to the likely cause before you grab tools. This saves you from replacing hinges that only need a turn of a screw.

SymptomLikely causeWhat to try
Door sags or drops at the outer cornerLoose mounting screws or stripped holesTighten screws, then repair stripped holes if they spin
Door rubs the frame or next doorMisalignmentAdjust side to side and height
Uneven gap along the door edgeHinges set at different depthsAdjust the depth screw on each hinge
Door will not shut fullyWrong overlay or hinge too tightLoosen depth setting, check overlay
Stiff or squeaky pin hingeRust or grimeClean the pin, remove rust, check for bending
Door slams or dragsWorn spring or damperReplace the hinge
Hinge arm bent or crackedOverload or impactReplace the hinge

How to adjust cabinet hinges with 2 screws

Yes, you can adjust most concealed cabinet hinges, and it takes only a Phillips or flat screwdriver. Many hinges have two adjustment screws on the arm. Brands differ, so check the movement before you commit to a screw.

Safety first: if you are working on a wall cabinet, support the door so it cannot swing and fall while you loosen screws. Use a stable step stool for high cabinets, and wear eye protection when drilling or driving screws overhead.

  • Open the door and look at the two screws on the hinge arm. Turn each one a quarter turn and watch what the door does.
  • The screw nearer the front or the door typically moves the door in and out, which changes the gap at the edge. The other screw typically moves the door left and right.
  • Make small changes, about a quarter turn at a time, then close the door and check the gap.
  • Adjust the top and bottom hinges by the same amount so the door does not twist.
  • If the door needs to move up or down, loosen the screws that hold the hinge to the mounting plate, slide the door, and retighten. Some hinges have a separate height screw instead.
  • Finish by tightening the mounting screws firmly, but not so hard that you strip the holes.

Fixing stripped screw holes and loose hinges

If a screw spins without gripping, the hole is stripped. Tightening harder only makes it worse. Remove the screw and pack the hole with a few wooden toothpicks or a small glued wooden dowel, let the glue set, trim it flush, and drive the screw back in. This gives the threads fresh material to bite.

Another option is to move the hinge slightly so the screw lands in solid wood. This works best on face frames. On thin panels, use the screw length the hinge was made for. A screw that is too long can poke through the other side, and one that is too short will not hold.

Replace any hinge that is bent, cracked or rusted through. A damaged hinge puts a twist on the door and will pull screws loose again. Clean and lightly lubricate sticky pin hinges, and wipe moving parts dry so grime does not build up again.

Choosing replacement hinges that last

When a hinge is past saving, pick one that fits what you already have. Start with overlay, because it decides how far the door covers the frame. The top five in our best cabinet hinges comparison are all 1/2 inch overlay, so measure your door and frame first.

Next, match the cup size and screw spacing so the new hinge sits in the existing holes. In our data, four models list a 35 mm cup and one lists 30 mm. The Ravinte and Chibery models list 45 mm screw hole spacing. Matching these avoids new drilling, which is a common cause of weak holes.

Adjustability helps you avoid repeat binding. The KONIGEEHRE hinge lists 6-way adjustment, while the Ravinte and Chibery models list 3-way adjustment. More adjustment gives you more room to fix sag later. You can see all of these side by side on our cabinet hinge comparison page.

Finally, check that a hinge is real soft close and not only self-closing. Spring hinges that self-close may close with more noise, while a damper slows the last part of the swing and saves wear on doors and frames. Stainless steel resists rust better than plain steel, which matters in kitchens and baths.

Frequently asked questions

Can I adjust hinges without taking the door off?

Yes. Concealed hinges are designed to be adjusted with the door hanging. Only remove the door if you need to repair a stripped hole or replace a hinge.

How tight should the hinge screws be?

Snug and firm, but stop as soon as the screw seats. Overtightening strips wood and can crack thin panels.

Should I lubricate a sticking hinge?

For pin style hinges, clean off grime and rust first, then add a small amount of light lubricant to the pin and wipe away the excess. Do not spray lubricant on soft close dampers.

How many hinges should a tall or heavy door have?

Taller or heavier doors usually need more hinges to share the load. Check the hinge maker's guidance for your door size and weight.

Why does my door still bind after adjusting?

The door may be warped or swollen, or the cabinet may be out of square. A worn damper or spring can also cause drag, and that calls for a new hinge.

Compare the products