Which Whetstone Grit Should You Use First?
Use the coarsest grit your knife actually needs. That means a low grit around 400 for dull, chipped or damaged edges, and a medium grit around 1000 if the knife is only slightly dull. On a two-sided stone, start with the lower-numbered side, then move to finer grits to refine the edge.
What whetstone grit means
Grit is a number that describes how coarse the stone's abrasive is. A low number means larger particles that remove metal quickly. A high number means finer particles that smooth and polish the edge.
That is why our best whetstone comparison treats grit range as the first thing to check. Low grit such as 400 repairs dull or damaged edges. High grit such as 8000 refines and polishes. The stone you start on sets how much metal you remove, so it matters more than the finishing stone.
Pick your first grit by edge condition
Look at the knife before you pick a side. The edge condition tells you where to begin. Starting too fine on a damaged blade wastes time, because a fine stone removes metal slowly. Starting too coarse on a knife that only needs a touch-up removes more steel than necessary.
The table below gives a simple starting point. It matches how the stones in our comparison are described, where the 400/1000 sides are for repairing and sharpening and the 3000/8000 sides are for refining.
| Edge condition | Start with | Then move to |
|---|---|---|
| Chipped, nicked or very dull | About 400 grit | 1000, then a fine stone of 3000 or higher |
| Dull from regular use | About 1000 grit | 3000 to 6000 grit |
| Slightly dull, mostly needs a touch-up | 1000 grit or a medium-fine stone | Finish with a strop if you have one |
| Already sharp, needs polish only | 3000 grit or higher | 8000 grit for a very fine finish |
Which side of the stone to use first
Many kits pack two grits into each stone, one on each face. The Intelitopia set in our comparison, for example, pairs a 400/1000 stone with a 3000/8000 stone. The HMPLL and Wucgea kits use the same pairing.
Always begin with the lower-numbered side of the stone that matches your edge. For a damaged knife, that is the 400 side of the first stone. For a knife in decent shape, flip to the 1000 side. Finish on the 3000 side and then 8000 if you want a polished edge.
Check which side is which before you wet the stone. Some stones label the grit on the edge, and some only on the packaging. Mark the coarse side with a pencil dot if it is not clear.
A simple order to follow
Once you know your starting grit, the sequence is the same for most kitchen knives.
- Soak the stone in water as the listing for your stone directs. Several kits in our comparison call for about 5 to 15 minutes.
- Set the stone on a non-slip base so it cannot move.
- Work the lowest grit you need until you feel a burr, a thin ridge of metal, along the whole edge on the opposite side.
- Switch to the next higher grit and repeat with lighter pressure.
- Finish on the finest stone you own, then use a leather strop if included to remove the burr.
- Rinse and wipe the knife, then dry it fully.
Is a 1000 grit whetstone enough?
For routine upkeep on a knife that is already in fair shape, a 1000 grit stone gives a usable working edge. It is the medium step that sits between repair and polish.
It has limits. A 1000 stone alone will leave a coarser edge than a finer stone would, and it is slow on chips. Our buying guide notes that a 1000 to 6000 stone handles routine upkeep but takes longer on chipped edges. The KEENBEST set in our comparison covers 400 to 1000 grit, which suits repair and basic sharpening, but it has no fine stone for finishing.
If you want a smoother edge, add a finer stone later. A 400 to 8000 range covers the full job, from repair to polish.
Stone prep and safety
Two habits keep your stone useful and your hands safe. First, flatten the stone. Whetstones wear into a dish with use, and a dished stone gives uneven edges. The Intelitopia, HMPLL and Wucgea kits include a flattening stone. The KEENBEST and Sharp Pebble sets do not, so you would need to buy one separately.
Second, keep the stone from sliding. A stone that moves is slow and unsafe. Use a base with a non-slip surface, a rubber support or a silicone holder.
A few more safety points:
- Keep your fingers behind the cutting edge and never run them along the blade to test it.
- Wipe the knife with the spine toward you and the edge away.
- Use a damp cloth under a loose base, and never sharpen over a wet floor.
- Wear safety glasses if you work with any dry diamond plate, and follow the listing's instructions on whether to use water. The diamond plate in our comparison says to sharpen dry.
Choosing a stone that fits your first step
If you are not sure how damaged your knives are, a wide range is the safest buy. A 400 to 8000 kit lets you start low when needed and finish fine. You can compare these side by side on our whetstone comparison page.
Beginners may also like an angle guide, which helps hold a steady angle. The Sharp Pebble set offers 1000 to 6000 grit with an angle guide, while the Intelitopia kit adds a guide, strop and flattening stone to the 400 to 8000 range. If you only maintain sharp knives, a 1000 to 6000 stone is enough and you can skip the coarse grit.
Frequently asked questions
Do I need to start at 400 grit every time?
No. Use 400 only when the edge is chipped, nicked or very dull. For routine touch-ups, begin at 1000 and move up.
Should I soak every whetstone?
Not always. Many water stones need soaking, and kits in our comparison list 5 to 15 minutes. Check your listing, since the diamond plate we list is meant to be used dry.
Can I skip grits when moving up?
Small jumps work best. Going from 1000 straight to 8000 is possible, but a step at 3000 or 6000 usually removes scratches more easily.
How do I know when to switch to the next grit?
Switch when you can feel a burr along the full length of the edge. That means the current stone has done its job.
Intelitopia MDS00ABest overall
HMPLL Knife Sharpening Stone SetMost pieces in the kit
wucgea 8 in 1Lighter full kit