What Size Truck Tool Box Fits My Truck?
The right size depends on your bed and the box style, not just the truck's class. Measure the width between your bed walls, the space behind the cab and the height to your rear window line, then pick a box that leaves a couple of inches of room on each side. In the models on our comparison page, crossover boxes run 70 in or 77 in long, chest boxes run 39 in to 48 in, and an underbody box is sized to the space under the vehicle.
Start with the style, then the size
Tool box sizes only make sense once you know where the box goes. A crossover box spans the bed behind the cab, so its length has to match your bed width. A chest box sits along one side of the bed, so its length is limited by how much bed length you can give up. An underbody box hangs below the frame and does not use bed space at all.
That is why the question "how long is a full size truck tool box" has no single answer. In our data, the crossover boxes are 70 in and 77 in long. The chest boxes are 48 in and 39 in long. Same truck, very different boxes.
How to measure your truck
You need a tape measure, a pen and about ten minutes. Write each number down and keep it next to the box dimensions when you shop. Always confirm fit with the maker before you buy, because bed liners, rails and trim can change the usable space.
- Measure the width between the bed walls at the top of the rails. This sets the maximum length for a crossover box.
- Measure the width at the bottom of the bed, near the floor, in case wheel wells or liner ribs narrow the space.
- Measure from the cab wall to the tailgate. Leave room for the tailgate to open and close with the box in place.
- Check the height from the bed floor to the top of the rail, and think about your rear window. A tall box can block your view out the back.
- Note any bed rails, tie-down cleats or an existing liner that could touch the box or the lid as it opens.
Match length to your bed
A box should be a little smaller than the space it sits in, not a perfect fit. A common rule of thumb is to leave about 2 inches of slack in total across the width so you can lower the box in and bolt it down without forcing it. Also make sure the lid can open fully without hitting the cab or the rear window.
Crossover boxes in our lineup are 70 in or 77 in long, so a narrow bed may not fit them. If your bed width is close to the box length, check the exact listed dimensions again and ask the maker. The COOLBAG crossover on our comparison page measures 70 × 20 × 15 in and is listed as sized for full-size trucks, with a 10.6 cu ft capacity.
Compare sizes by box style
The table below uses real figures from the products on our best tool box for truck page. Use it to get a feel for the range, not as a fit guarantee for your truck.
| Style | Example size (L × W × H) | Listed weight | Where it goes |
|---|---|---|---|
| Crossover | 70 × 20 × 15 in | Not listed | Across the bed behind the cab |
| Chest | 48 × 15 × 15 in | 25.6 lb | Along one side of the bed |
| Chest | 48 × 15 × 15 in | 28 lb | Along one side of the bed |
| Small chest or rack box | 39 × 13 × 10 in | 20.45 lb | Bed, hitch rack or trailer |
| Underbody | 48 × 17 × 18 in | 37.8 lb | Below the frame, not in the bed |
Height, weight and payload
Length gets the attention, but height and weight matter too. A low-profile box keeps your rear view clear. The 70 in COOLBAG crossover is described as low-profile for visibility through the rear window. On the other end, our page lists a 77 in box that is 24 in tall and weighs 58 lb, so it is big and uses up payload quickly.
Weight counts against your truck's payload. Add the box weight to the weight of the tools you plan to carry. Among the models on our page that list weight, the range runs from 8 lb to 60 lb. Some makers do not publish a weight, so ask before you buy. If you also want a portable option for your garage, see our picks for the best rolling tool box.
Check the features that affect fit
Some features change how much room you need. A gas strut holds the lid open, but the lid still swings up and back, so it needs clearance. Dual lids on a gull wing box open from the sides, which helps if your bed is crowded. Carry handles make it easier to lift the box into the bed, and a weatherproof seal and lock matter once it is installed.
If you are still deciding what kind of box you need overall, our general best tool box comparison covers other styles beyond truck mounts.
Safety notes for installing a truck box
Truck boxes are awkward and heavier than they look. Get a second person to help lift, and wear gloves. Keep your fingers clear of the lid edge, and use the support strut or prop when you load or unload.
If you drill holes in the bed or frame, wear eye protection and check what is behind the metal first. Underneath a truck there can be fuel lines, brake lines and wiring. One underbody box listing says to turn off the power when assembling it on the vehicle to prevent a short circuit, and that is good practice for any underbody work. Work from stable ground, never under a vehicle held up only by a jack, and never drive with a loose box or a box that is not bolted down.
Frequently asked questions
Can I put a 70 in crossover box in any truck bed?
Not always. The box has to be shorter than the width between your bed walls, with a little room to spare. Measure your bed and compare it with the listed length before you buy.
Will a tool box block my rear window?
It can. Check the box height against the view from your driver's seat. A low-profile design helps, and a very tall box can get in the way.
Do I need to know my exact truck model?
It helps, but measuring your own bed is more reliable. Liners, rails and trim change the usable space, so use your measurements first.
Is an underbody box a good choice if my bed is small?
It can be, since it does not use bed space. You still need enough clearance under the vehicle, so measure that area and confirm fit with the maker.
VEVOR JL-TB19-3Best overall
VEVOR UTTB-481718Under-vehicle storage
COOLBAG CB1150Largest listed capacity