What Size Thickness Planer Do You Need for Your Boards?
For most home shops, a benchtop planer that takes boards 12.25 to 13 inches wide and about 6 inches thick is enough. Measure your widest board and your thickest board, then pick a planer that clears both with a little room to spare. For oak and other hardwoods, capacity matters less than a strong motor and a sharp cutterhead.
The two numbers that decide your size
Every planer has a maximum board width and a maximum board thickness. These two numbers tell you whether a board will fit at all, so check them before anything else.
Width is the limit most people hit first. The benchtop models we compare list 12.25 to 13 inches of width. Thickness is usually around 6 inches, which covers nearly all standard lumber, including chunky table legs and workbench tops.
A third number matters too, and that is the minimum thickness. Some listings show a floor of about 1/4 inch, so you cannot plane a board down to a thin veneer on every machine. Check the manual if you plan to make thin parts.
How to measure your boards
Do this before you shop. It takes a few minutes and prevents the most common mistake, which is buying a planer that is a half inch too narrow.
Measure the stock you buy now, and the stock you expect to buy in a year or two. A planer is easier to live with if it fits your wider boards without a fight.
- Measure the widest board you plan to plane, in inches.
- Measure the thickest board you plan to plane.
- Note the longest board. Long boards need extra support on both sides of the machine.
- Write down your hardest wood, such as oak, maple or walnut. That decides how much motor and cutterhead quality you want.
- Decide the final thickness you need. If you often go thinner than 1/4 inch, check the minimum thickness.
What the published specs show
The table below uses the published specs from the benchtop planers on our comparison page. Weights are listed in pounds. A dash means the spec sheet we have does not list that number.
Notice how tight the range is. The width difference between the narrowest and widest model is under one inch. That is why checking your own boards matters more than chasing the largest number.
| Model | Max width (in) | Max thickness (in) | Weight (lb) |
|---|---|---|---|
| CRAFTSMAN CMEW320 | 12.25 | - | 62.92 |
| DEWALT DW734 | 12.5 | 6 | 83.38 |
| VEVOR 12.5 in | 12.5 | 6.3 | 78 |
| DEWALT DW735 | 13 | 6 | 91.25 |
| Cutech 40800H (spiral) | 13 | 6 | 69.2 |
| VEVOR 13 in (spiral) | 13 | 6 (per listing) | 61.73 |
| WOODERS PL13-15AB | 13 | 6.3 | 60 |
Choosing by board width
If most of your boards are under 12 inches wide, a 12.25 or 12.5 inch planer will do the job. Typical 1x12 and 2x12 lumber is narrower than the stated nominal size once milled, so it generally fits. Check your actual board first.
If you work with wider boards, such as glued-up panels or tabletop slabs, a 13 inch model gives you a little more room. It will not handle a 15 inch slab, though. For that, you would plane it in two halves, glue it up after, or use a larger machine.
Wider is not always better in a benchtop. Bigger machines weigh more, take more bench space and need a stronger motor to cut across the full width. The planers in our data weigh from about 60 to over 91 pounds, so think about where you will store and lift yours.
Choosing by thickness and hardwood
A 6 inch thickness limit suits nearly every home project. You only need more if you plan to plane thick beams or large timbers, and that usually calls for a bigger machine than a benchtop.
For oak and similar hardwoods, take light passes and keep the feed steady. Taking too much per pass can stall the motor, leave rough spots or cause tearout. Slowing the feed helps. The DEWALT DW735 lists two feed speeds, 96 or 179 cuts per inch, and the Cutech lists a 2-speed lever with a slower setting for hardwood and figured wood.
Cutterhead type matters here as well. Straight knives work well on straight-grained wood, while spiral heads with small carbide inserts tend to cut quieter and smoother on figured grain. If you plan to plane a lot of oak, our best thickness planer for the money page puts capacity, motor and cutterhead side by side so you can compare value.
Size, snipe and long boards
Snipe is a deeper cut at the end of a board. It is more noticeable on wide or long stock. Planers with carriage locks or anti-snipe designs reduce it, and so does supporting the board on both sides of the machine.
Some listings give support lengths. The DEWALT DW734 lists 33-1/2 inches of material support, and the VEVOR 13 in lists a 28.2 inch worktable. Longer support helps on long boards, but you may still need roller stands for anything longer than the tables.
Always check that your longest board will be supported in and out of the cut. An unsupported board can tip, bind or kick back.
Safety before you plane
Planers are loud, throw lots of chips and run on a high-amp motor. Take a few minutes to set up safely.
Wear hearing protection and safety glasses every time. Use a dust collector or shop vac on the dust port, since fine dust is a breathing hazard. Check boards for nails, screws and grit before they go through, especially reclaimed wood, because metal can damage the cutterhead and throw fragments.
Unplug the machine before changing knives or inserts, or clearing a jam. Keep your hands away from the feed opening, and never stand directly in line with the board as it feeds. Plug into a circuit that suits a 15 amp tool, and avoid long, thin extension cords.
A quick way to decide
Pick the smallest planer that clears your widest and thickest boards with some margin. Then use your wood type to narrow the choice by motor, cutterhead and feed speed.
If you want help comparing options, our best thickness planer page ranks the same machines by overall score, and the value page above shows how they compare on features.
Frequently asked questions
Can I plane a board wider than my planer?
Not in one pass. You can rip it narrower, plane the halves and glue them back together, or flatten it by another method. Forcing a board through a planer that is too narrow is unsafe.
Is a 13 inch planer better than a 12.5 inch one?
It handles slightly wider boards, but the difference is small. If your boards fit, other features such as cutterhead type, snipe control and weight may matter more.
Do I need a bigger planer for oak?
Usually not. Oak needs light passes, sharp cutters and a motor that does not stall, more than extra width. A slower feed speed can also reduce tearout.
How thin can a planer make a board?
It varies. Listings such as the WOODERS and VEVOR 12.5 in show a minimum near 1/4 inch or 0.2 inch. Check the manual for your model.
CRAFTSMAN CMEW320Best value overall
DEWALT DW735Best finish with knives
CUTECH 40800HBest spiral value