Guide

What Size Reciprocating Saw Blades for Trees Do You Need?

For most tree and shrub work, a 9 inch or 12 inch pruning blade with about 3 to 6 teeth per inch (TPI) is the right choice. Choose a blade at least 2 to 3 inches longer than the branch is thick, so the teeth can clear the cut. Use shorter blades for small shrubs and longer ones for thick limbs or hard to reach spots.

Updated 2026-11-12 · Based on published specifications and maker information

Top picks from our best reciprocating saw blades for trees comparison

The short version: length and teeth

Two numbers decide whether a blade works well on wood: length and TPI. Length controls how thick a branch you can cut in one pass. TPI controls how fast the blade cuts and how rough the cut is.

For green, living wood, coarse teeth work best. They take big bites and clear sap and wet sawdust instead of clogging. Fine teeth gum up quickly in fresh wood and tend to burn or stall.

That is why pruning blades look so different from metal cutting blades. They have wide, deep gullets (the gaps between teeth) and a more aggressive tooth shape.

Match blade length to branch thickness

A reciprocating saw blade moves back and forth, and only part of its length is useful in the cut. The rest is needed for the stroke and for chip clearance. A common rule of thumb is to pick a blade 2 to 3 inches longer than the wood is thick.

Blades are commonly sold from about 4 inches up to 12 inches, with some pruning styles running longer. The chart below shows a practical starting point. Treat it as a guide, not a hard limit.

MaterialTypical thicknessBlade length to start withSuggested TPI
Shrub stems and thin twigsUp to 1 inch6 inch5 to 6
Small branches1 to 3 inches9 inch3 to 6
Medium limbs3 to 6 inches9 to 12 inch3 to 5
Thick limbs6 inches and up12 inch or longer3 to 4
Dead, dry woodAnySame lengths as aboveSlightly finer, 5 to 8

Choosing TPI for different jobs

Think of TPI as a trade between speed and smoothness. Fewer teeth per inch means a faster, rougher cut. More teeth means a slower, cleaner cut.

For fresh branches and limbs, stay in the lower range. Green wood is wet and fibrous, so it needs the room that big gullets provide. For dry, seasoned or dead wood, you can move up a bit, since there is less sap to clog the teeth.

Some blades have variable tooth spacing or a mix of tooth styles. These can be a good all around choice when you cut a range of branch sizes in one session.

  • 3 to 4 TPI: thick, green limbs where speed and chip clearance matter most
  • 5 to 6 TPI: small to medium branches and general pruning
  • 6 to 8 TPI: dry or dead wood, or when you want a cleaner finish
  • Above 10 TPI: usually meant for metal or plastic, not live wood

Trees, shrubs and pruning: small differences

Shrubs and small trees usually have thin, flexible stems. A shorter blade is easier to control there and is less likely to whip around in tight growth. A 6 inch pruning blade is often enough.

For tree limbs and branches, a 9 inch blade covers most backyard work. Move to 12 inches when the limb is thick or you need reach into a crowded canopy. A longer blade also lets you saw from a safer position.

If you are cutting roots or stump material, dirt dulls teeth fast and the work is harder on blades. Our page on the best reciprocating saw blade for tree roots covers blades built for that kind of abuse. For general limb work, see our best reciprocating saw blades for trees comparison, which lays out published specifications side by side.

How to cut a branch with a reciprocating saw

Good technique protects both the blade and you. A few habits make cuts cleaner and keep the saw from jumping.

  • Remove the battery or unplug the saw before you change a blade.
  • Seat the blade fully in the clamp and check that it is locked.
  • Rest the saw's shoe firmly against the branch before you pull the trigger. This cuts down on vibration and blade chatter.
  • Start the cut at a low speed, then increase once the teeth bite.
  • Let the blade do the work. Pushing hard can bend it or make it bind.
  • For heavy limbs, make a small undercut first, then cut from the top so the limb does not pinch the blade or tear bark down the trunk.
  • Cut thick limbs in sections so you control where the weight falls.

Safety notes you should not skip

Wear safety glasses, hearing protection and sturdy gloves. Sawdust, wood chips and a snapped blade can all fly toward your face, and a saw running on a limb is loud.

Never cut near power lines, and keep yourself and the falling branch well clear of them. If a limb touches or leans on a line, call a professional.

Avoid working on a ladder with a running saw. A reciprocating saw can kick when it binds, and that is a bad moment to lose your balance. Keep your feet on the ground, use a pole saw or call an arborist for high limbs, and never cut above shoulder height.

Corded saws add another risk. Keep the cord behind you and away from the blade, and use a cord rated for outdoor use. Do not use electric tools in wet conditions.

Quick checklist before you buy

Measure the thickest branch you expect to cut, add 2 to 3 inches, and pick the nearest standard length. Then pick a coarse tooth blade made for wood or pruning.

If you cut many different sizes, buying one short and one long blade is often better than a single compromise. When comparing specific models, check that the listed length, TPI and tooth style match the job.

Frequently asked questions

Can I use a metal cutting blade on a tree branch?

You can, but it will cut slowly and clog with sap and sawdust. Fine teeth are not made to clear wet wood, so a pruning blade is the better tool.

Is a thicker blade better for big limbs?

A stiffer, thicker blade resists bending and is less likely to wander in a long cut. Pruning blades vary in thickness, so check the listed specifications when you compare them.

Can a reciprocating saw cut down a whole tree?

It can handle small trunks if the blade is long enough, but it is not the safest tool for felling. Larger trees need proper felling tools and technique, or a professional.

Why does my blade keep binding in the cut?

Binding often comes from a pinched limb, a dull blade or too much pressure. Support the branch so the cut stays open, and make an undercut first on heavy limbs.

Compare the products