What Size PEX Expansion Tool Do You Need?
Choose the tool by the largest PEX-A pipe you will expand, then confirm the smallest size it handles. For most home plumbing, a tool that covers 1/2 in to 1 in is enough, but 1-1/4 in or 1-1/2 in lines need a tool with a higher listed maximum. Check the range, the PEX type and what is in the box before you buy.
Start with your largest pipe
A PEX expansion tool is sized by the pipe it can expand. Every tool lists a maximum tubing size, and it cannot go past that limit. So the first step is to find the biggest PEX you will connect, such as a main supply line, and match the tool to it.
Among the six tools on our spec sheet, five stop at 1 in. Only the DEWALT DCE410 lists 1.5 in. If your project never goes above 1 in, you have plenty of choices. If it includes 1-1/4 in or 1-1/2 in pipe, your list shrinks fast. Our best PEX expansion tool comparison shows all six side by side.
Check the small end of the range
The low end matters too. Some tools start at 3/8 in, which is 0.375 in, and some start at 1/2 in. If you run 3/8 in lines to a faucet or a fixture, a tool that starts at 0.5 in will not work for those connections.
In our data, four of the six tools start at 0.375 in. The VEVOR CEP401-18BL and the Milwaukee 2532-20 start at 0.5 in. Write down every pipe size in your plan, smallest to largest, and make sure one tool covers the whole list.
Confirm the tool fits your PEX type
Expansion tools are made for PEX-A. This pipe is designed to expand, slip over a fitting, and then shrink back to grip it. PEX-B and PEX-C are not made for this method, so an expansion tool is the wrong choice for them.
The VEVOR lists PEX-A only, and the DEWALT listings name Type-A. The Milwaukee listings in our data do not state a type, so confirm it with the maker before you buy. Also match your fittings to the tool and the tubing, and read the fitting maker's instructions.
Size ranges of six tools
The table below pulls the listed size range, maximum size and weight for each product. It also shows how many expansion heads each listing includes. A dash means the listing does not state it.
Heads often match specific pipe sizes, so a missing head is another reason to check the box contents. For a fuller side-by-side view, see our PEX expansion tool comparison.
| Tool | Size range (in) | Max size (in) | Weight (lb) | Heads listed |
|---|---|---|---|---|
| VEVOR CEP401-18BL | 0.5 to 1 | 1 | 11.64 | 3 |
| DEWALT DCE400B | 0.375 to 1 | 1 | 3.9 | - |
| DEWALT DCE410 | 0.375 to 1.5 | 1.5 | 7.7 | - |
| DEWALT DCE400D2 | 0.375 to 1 | 1 | 3.9 | - |
| Milwaukee 2532-22 | 0.375 to 1 | 1 | 4.5 | 3 |
| Milwaukee 2532-20 | 0.5 to 1 | 1 | 4.5 | - |
Heads, batteries and weight
Once the size range fits, look at what else decides how the tool works for you. Three of the six listings are bare tools with no batteries, so count what you would need to add.
Weight runs from 3.9 lb to 11.64 lb in our data. That gap is large if you work overhead or on a ladder. Keep these points in mind:
- Heads: the VEVOR and the Milwaukee 2532-22 each list 3 heads. The VEVOR names 1/2 in, 3/4 in and 1 in.
- Batteries: the VEVOR, DEWALT DCE400D2 and Milwaukee 2532-22 list two batteries. The other three list none.
- Voltage: four tools use 20 V batteries and the two Milwaukee tools use 12 V, so match any packs you already own.
- Light and rotation: all six list auto rotation, and five list an LED light. The DCE410 does not list one.
How to expand PEX safely
Always follow your tool's manual first. The basic flow below is the same for most cordless expanders, and the steps are general rather than specific to one product.
Wear safety glasses, because tubing and rings can shift under force. Keep fingers clear of the head and the tubing end. Use only the batteries and charger the maker lists. If you work near a water heater or live wiring, shut off power and water first.
- Cut the pipe square and clean, with no burrs.
- Slide the expansion ring onto the pipe.
- Pick the head that matches the pipe size and fit it to the tool.
- Insert the head and expand the pipe in short cycles, letting the head rotate.
- Remove the head, then push the fitting in right away while the pipe is still expanded.
- Hold the joint until the pipe shrinks back, then check that the ring sits flush.
Frequently asked questions
Can one tool handle every PEX size?
Not always. Each tool lists a range, and most stop at 1 in. Check both ends of that range against your plan. If you also need 1-1/2 in pipe, the DEWALT DCE410 is the only one on our sheet that lists it.
Why does weight matter?
A heavy tool is tiring to hold above your head or in tight spaces. Listed weights run from 3.9 lb to 11.64 lb among the six tools, so a lighter model suits ceiling and ladder work better.
Do I need to buy batteries separately?
It depends on the listing. Three of the six tools list zero batteries, so you would need compatible packs and a charger. The other three list two batteries each.
Does the tool also need lubricant?
Some do. The VEVOR listing asks you to add lubricating oil before use. Check your tool's manual for any upkeep it needs, since that varies by maker.
VEVOR CEP401-18BLBest overall
DEWALT DCE400BLight bare tool
DEWALT DCE410Largest pipe capacity