Guide

What Is a Utility Pump Used For?

A utility pump is a portable submersible pump that you drop into standing water, connect to a hose and plug in to move that water somewhere else. People use it to drain flooded basements, window wells, pool covers, hot tubs, water heaters and clogged tubs. It is built for short, hands-on jobs, not for sitting in a pit and running on its own.

Updated 2026-11-12 · Based on published specifications and maker information

Top picks from our best utility pump comparison

What a utility pump is

A utility pump is a small electric pump that works underwater. The motor and impeller sit in one sealed housing. You set it in the water, attach a hose to the outlet, plug it in and the pump pushes water out through the hose.

Most models are light enough to carry with one hand. Many have a screened inlet at the bottom that keeps larger debris out, plus hose adapters so you can connect a garden hose or a flat discharge hose. Because it is portable and general purpose, people also call it a portable utility pump, a submersible utility pump or a utility transfer pump. These names describe the same basic tool.

Most utility pumps have no float switch. They start when you plug them in and stop when you unplug them. That means you stay nearby while it runs and watch the water level.

Common jobs for a utility pump

The pump suits any job where water is sitting in the wrong place and you want it gone. Here are the jobs people reach for one most often:

  • Draining a flooded basement, crawl space or garage after a storm or a burst pipe
  • Emptying a window well that has filled with rain
  • Removing water from a pool cover or a flat roof
  • Draining or flushing a hot tub
  • Flushing a water heater, including tankless units
  • Emptying a clogged laundry tub or bathtub
  • Moving water from a garden pond or rain barrel to another spot, or watering the yard through a hose

Utility pump vs sump pump vs utility sink pump

These terms get mixed up, so here is a plain split. A sump pump sits in a pit in the basement floor and usually has a float switch that turns it on when water rises. It handles groundwater and runs automatically for years. A utility pump has no permanent home. You bring it out when you need it and put it away afterward.

A utility sink pump is a different product. It is usually a fixed unit that lifts the drain water from a basement laundry sink up to your home's drain line. A portable utility pump can empty a laundry tub in a pinch, but it does not replace a pump built into the plumbing.

A transfer pump moves water from one container or place to another, such as a tank to a garden bed. A utility pump does this well for clean or lightly dirty water. For muddy, gritty or sewage-type water, you need a pump designed for solids. Some listings, such as the 6699 SUB 1500 and SUB 1600, say plainly that they are not for dirty water.

Specs that decide whether a pump fits your job

Four numbers on a spec sheet tell you most of what you need. Flow, in gallons per hour (GPH), shows how fast the pump moves water. Max lift shows how high it can push water, which matters if you need to reach a window, a yard or a drain above the water. Minimum water depth shows how shallow it can pump before it sucks air. Thermal overload protection helps protect the motor if it runs dry or overheats.

Here is how several pumps from our comparison line up on published specs:

PumpMotorMax flowMax liftLowest water depth
Seesii BDP90011 HP4,755 GPH36 ftNot listed
AQUASTRONG ESU100PM1 HP4,500 GPH30 ft0.2 in
Cleartide EUZP25A0.33 HP2,760 GPH32 ft0.16 in
6699 SUB 15000.25 HP1,500 GPH23 ft0.083 in
6699 SUB 16000.25 HP1,600 GPHNot listed0.083 in

Matching the pump to the job

For a large basement or a big pool cover, higher flow saves time. A 1 HP pump with 4,500 to 4,755 GPH on its spec sheet moves water much faster than a 1/4 HP pump rated at 1,500 to 1,600 GPH. For a hot tub, a water heater flush or a small window well, a compact pump is usually enough.

Lift matters when the water has to go uphill. If you are pumping from a basement to a window or a yard, check the max lift. Remember that published flow numbers are maximums, and real flow drops as the hose gets longer or the discharge point gets higher.

If you want to leave as little water behind as possible, look at the lowest water depth. The two 6699 models list 0.083 in, while the Cleartide lists 0.16 in. After the pump stops pulling, you can finish the last bit with a mop or a wet vac.

Accessories also count. The Seesii listing includes a 23 ft hose, adapters and a 25 ft cord, so you can start without buying extras. Several others list adapters but shorter 10 ft cords. Our best utility pump page puts these specs side by side so you can compare flow, lift and cord length at a glance.

How to use a utility pump safely

Electricity and water are a risky mix, so slow down before you plug anything in.

Follow these steps:

  • If water is near outlets, appliances or your breaker panel, do not enter the area. Have the power shut off at the main, or call an electrician.
  • Plug the pump into a GFCI-protected outlet. If you need an extension cord, use one rated for outdoor use and keep the connection out of the water.
  • Set the pump on a flat, solid surface, such as a board or a few bricks, so the inlet does not suck in mud.
  • Connect the hose and run it to a drain or an area where the water can safely flow away from your home's foundation.
  • Plug in the pump, then stay nearby. Unplug it before you reach into the water or touch the pump.
  • Unplug it as soon as it starts sucking air or the water is gone. Running dry can overheat the motor, even on models with thermal protection.
  • Rinse the pump and clean the inlet screen before you store it.

When a utility pump is the wrong tool

A utility pump is not meant for fuel, solvents or sewage. Do not use it for flammable liquids, because the motor can spark. Do not use it where hot tub chemicals could pool in a place that harms plants or storm drains. Check your local rules for where treated water may go.

It also does not replace a sump pump if your basement floods again and again. A portable pump only works while you are watching it. If water keeps returning, a float-switch sump pump is the better long-term answer. Keep a utility pump as the backup for emergencies and one-off drains.

If you are working on a roof or a ladder to set up a pool cover pump, take care with footing and never lean over wet surfaces while the pump is plugged in. For help choosing, see our utility pump comparison.

Frequently asked questions

Can a utility pump drain a pool?

It can drain a pool cover or a small pool slowly. For a full pool, check local rules about where the water can go and do not let it flow toward your foundation or a neighbor's yard.

Does a utility pump turn off by itself?

Usually not. Most have no float switch, so you unplug the pump when the job is done. Check the product listing if you want an automatic model.

Can I use a utility pump with a garden hose?

Often yes. Many include adapters, such as the 3/4 in garden hose adapter listed with the 6699 pumps. Check the discharge size and adapters before you buy.

How much water will it leave behind?

It depends on the pump. Published minimum depths range from 0.083 in to 0.2 in among the pumps we list. A mop or wet vac handles the rest.

Compare the products