What Is a Timing Light and How Does It Work?
A timing light is a strobe lamp that flashes each time the number one spark plug fires. Aimed at the timing marks on the crank pulley or flywheel, it makes those spinning marks look frozen, so you can see exactly when the spark happens relative to piston position. Mechanics use it to check and set ignition timing on distributor-based engines.
How a timing light works
A timing light has three basic parts: a pickup that senses the spark, a circuit that turns that signal into a flash, and a bright strobe lamp. When the number one cylinder fires, the pickup senses the pulse in the spark plug wire. The light flashes at that exact instant.
The engine has a mark on the crank pulley or flywheel, and a fixed pointer or scale nearby. Because the strobe fires at the moment of the spark, the mark appears to stand still in the light. Where it sits against the scale tells you the ignition timing, usually in degrees before top dead center.
Your eye cannot follow a mark spinning at idle speed, but a flash that lasts a tiny fraction of a second can capture it. That is the whole trick. The light does not measure timing by itself. It shows you when the spark happens so you can compare it with your engine's specification.
Why ignition timing matters
Ignition timing is the moment the spark plug fires in relation to the piston's position. The fuel mixture needs a little time to burn, so the spark usually fires slightly before the piston reaches the top of its stroke.
If timing is off, the engine tells you. Typical symptoms include:
- Rough or unstable idle
- Hard starting
- Pinging or knocking under load
- Poor power and weak acceleration
- Poor fuel economy
How the pickup connects: inductive clamps
Most timing lights use an inductive pickup. This is a small clamp that goes around the number one spark plug wire. It senses the current pulse through the wire without cutting or piercing it, which is why you will see the term inductive timing light. The KZYEE KT60, for example, uses a directional inductive clamp, and its listing notes that correct placement matters for a stable signal.
Direction matters on many clamps. There is often an arrow that should point toward the spark plug. If the light flashes erratically, check that the clamp is on the right wire, seated fully and facing the right way.
Most lights also need a power source. Many connect to the 12V battery with two clips, and some rechargeable models run on their own battery instead. Either way, route the leads away from belts, fans and hot parts.
Basic lights versus digital advance lights
A basic timing light only flashes. You line up the mark with the scale by eye and adjust the distributor until the mark sits where the engine's specification says it should.
A digital advance light adds a control that delays the flash by a set number of degrees. You dial in the delay until the mark lines up with a fixed reference, and the screen shows the advance directly. This is handy when marks are hard to see or when you want to check how much advance the engine adds as speed rises.
Many digital lights also include a tachometer, dwell and voltage readings. The table below uses published specifications from the lights on our comparison page.
| Light | Digital advance | Tachometer max | Dwell and voltage | Weight |
|---|---|---|---|---|
| OBDMONSTER N300 Pro | Yes, 0 to 90° | 9999 RPM | Yes | 1.57 lb |
| KZYEE KT60 | Yes, 0 to 90° | 10000 RPM | Not listed | 1.41 lb |
| Innova 5568 Pro | Yes, 0 to 90° | 9990 RPM | Yes | 0.5 lb |
| Innova 3568 | Yes, 0 to 90° | 9990 RPM | No | 1.9 lb |
| ANCEL LT70 PRO | Yes, 0 to 90° | 9999 RPM | Yes | 1.46 lb |
Which engines and ignition systems work
This is where buyers most often go wrong. Timing lights are built for gasoline engines with a spark you can read at the number one plug wire. They are not for diesel engines, which have no spark plugs.
Ignition type matters too. Most lights work with distributor and distributorless (DIS) systems. Many do not work with coil-on-plug, CDI or MSD ignitions. The KZYEE KT60 listing says it is not intended for most coil-on-plug systems, the ANCEL LT70 PRO is listed for distributor-based systems and not CDI, and the Innova 5568 is listed as not suitable for MSD. The Innova 3568 is listed for 4-cycle engines only, while others cover 2- and 4-stroke engines.
Many modern engines also set timing through the computer, so there may be nothing to adjust by hand. Check your service manual for the right procedure and specification before buying. Our best timing light page lists ignition compatibility for each model so you can match one to your engine.
How to use a timing light safely
The engine has to run while you work, so treat the engine bay with care. Keep hands, hair, loose clothing and the light's leads clear of the fan, belts and pulleys. Some lights, like the Innova 5568, have a molded boot meant to protect against fan blades, but it is no substitute for careful handling.
Wear safety glasses, and never point the strobe at anyone's eyes. Work outdoors or with the garage door open and a way for exhaust to leave, because running engines produce carbon monoxide. Keep the light and its leads off hot exhaust parts. Spark plug wires carry high voltage, so handle them by the boot and avoid touching bare metal parts while the engine runs.
The usual steps look like this:
- Find the timing specification and mark location in your service manual, and clean the timing marks so you can read them.
- With the engine off, connect the power leads, observing correct polarity, and clamp the pickup onto the number one plug wire.
- Disconnect and plug any vacuum line the manual tells you to, and bring the engine to the speed the manual specifies.
- Aim the light at the marks and read where the mark sits against the scale, or dial in the advance on a digital light.
- If the reading is off, loosen the distributor hold-down slightly and turn it a little at a time, then tighten it and recheck.
- Shut the engine off before removing the clamp and leads.
Choosing a timing light
Start with compatibility. A light that does not suit your ignition system is of no use, whatever its features. Then decide how much you want beyond the strobe. A tachometer helps you hold the right engine speed, and dwell and voltage readings help with tune-ups on older systems.
Weight and cable length also matter in a crowded engine bay. The Innova 5568 is listed at 0.5 lb, while the OBDMONSTER N300 Pro and Innova 3568 weigh more and offer different feature sets. For a side-by-side view, see our best timing light comparison.
A good work light also makes marks easier to find before you start. If your engine bay is dark, our best work light page can help, and a magnet base can free up your hands, as covered on our best magnetic work light page.
Frequently asked questions
Can I use a timing light on a diesel engine?
No. Diesels do not use spark plugs, so there is no spark pulse for the pickup to read. Timing lights are meant for gasoline engines.
Why does the timing mark move when I raise the engine speed?
Many engines add advance as RPM rises, so the spark fires earlier. The mark appears to shift against the scale. This is why manuals give timing figures at a specified engine speed.
Do I need a tachometer on my timing light?
It is not required, but it helps. Timing specifications are often given at a certain RPM, and a built-in tach lets you confirm the speed without a separate gauge.
Why is my timing light flashing erratically?
Common causes include the clamp being on the wrong wire or facing the wrong way, a poor power connection, or an ignition system the light does not support. Check each in that order.
OBDMONSTER N300-US3Best overall
KZYEE KT60Highest RPM reading
Innova 5568Lightest pro light