Guide

What Is a Concealed Cabinet Hinge and How Is It Installed?

A concealed cabinet hinge is a hinge that mounts on the inside of the door and cabinet, so it stays out of sight when the door is closed. It has a round cup that sits in a drilled hole in the door and a mounting plate on the cabinet. Installing one takes four jobs: marking the door, drilling the cup hole, fixing the hinge and plate, and fine-tuning the fit with the adjustment screws.

Updated 2026-11-12 · Based on published specifications and maker information

Top picks from our best cabinet hinges comparison

What a concealed hinge is

A concealed hinge, also called a hidden or European-style hinge, has two main parts. The hinge arm carries a round cup that sits in a hole drilled into the back of the door. The mounting plate screws to the cabinet and the arm clips or screws onto it.

Because the cup is recessed into the door, you see only a clean door face when it is shut. Most models also have small adjustment screws, so you can move the door slightly up, down, in, out, left or right after it is hung.

Many concealed hinges include a damper for soft close. Not all do. A plain spring hinge simply pulls the door shut, and it may close with more noise. Check the spec for the words soft close, not only self-closing. Our best cabinet hinges page marks which models are true soft close.

What a frameless cabinet hinge is

Frameless cabinets, sometimes called European-style or full access cabinets, have no front frame. The box is made of side panels, and the door covers the edge of the panel. A frameless hinge has its mounting plate screwed to the inside of the side panel.

Face frame cabinets have a solid wood frame around the front opening. Hinges for these cabinets mount to the frame instead, and the plate is often a different shape so it can reach the frame's edge. The door covers part of the frame, and how much it covers is called the overlay.

Some hinges work on both styles. One model on our comparison page lists use on face frame and frameless cabinets with a 1/2 inch overlay. Others list face frame only, so read the label before you order.

Can you swap old hinges for hidden ones?

Often yes, but it depends on what is on your doors now. If your doors already have 35 mm round holes drilled for cup hinges, a new concealed hinge can drop into the same holes. That is the easiest swap, and you may need no new drilling at all.

If your doors currently use exposed butt hinges or surface-mount hinges, there are no cup holes. You will need to drill a cup hole in each door, which calls for a drill press or a guide jig and the right bit. Filling old screw holes and adding new plate holes on the cabinet is also part of the job.

The existing screw hole spacing matters too. If the new plate holes do not line up with old ones, fill the old holes with wood filler or glued dowels first, then let them dry before drilling again.

Check these specs before you buy

Hinges only fit well if four numbers match your doors: overlay, cup diameter, screw hole spacing and opening angle. Our published specs show how much these vary.

Here are examples from the hinges on our comparison page:

HingeCup diameterScrew hole spacingOpening angleAdjustment
KONIGEEHRE soft close35 mmNot listed105 degrees6-way
Ravinte JL11LS235 mm45 mm105 degrees3-way
Chibery 3D soft close35 mm45 mm105 degrees3-way
Bumper and plate kit (24 pack)30 mm48 mmNot listedNot listed

How to install concealed hinges

Gather a tape measure, pencil, power drill, a bit matched to the cup size, a screwdriver and a square. The maker's instructions give the exact distance from the door edge to the cup, so follow those over any general rule.

  • Measure and mark. Lay the door flat, back side up. Mark the center of each cup hole, usually a few inches in from the top and bottom, and set the distance from the door edge as the instructions say.
  • Drill the cup holes. A 35 mm cup needs a 35 mm bit. Listed cup depth on the Ravinte and Chibery models is about 11.5 to 11.6 mm, so drill only that deep. Use a depth stop, and test on scrap wood first so you do not go through the door face.
  • Seat the hinge. Place the cup in the hole, square the arm to the door edge, and drive the screws. Use the screws that come in the pack and keep them straight.
  • Fix the mounting plates. Screw the plates to the cabinet at the marked heights. Hold the door up with a helper or small shims to line up the plate positions.
  • Hang the door. Clip or screw each hinge arm onto its plate. Close the door and look at the gaps.
  • Adjust. Use the adjustment screws to level the door and even out the gaps. Small turns go a long way.

Adjusting and troubleshooting

A hinge with 3-way adjustment lets you move the door up and down, in and out, and side to side. Models listing 6-way adjustment add more control for tricky alignment. Adjust one hinge at a time and check the door after each turn.

If the door will not close flush, the most common cause is a mismatched overlay. A wrong overlay can leave gaps or stop the door from shutting. Measure how far your door covers the frame or panel before ordering, and compare it with the listed overlay.

If the door sags after installation, check that the screws bit into solid wood. In soft or damaged holes, glued dowels or longer screws may help, if they fit the plate.

If you want more help choosing, see how we rank soft close, material and fit data on our cabinet hinge comparison.

Safety notes

Wear safety glasses when drilling, because wood chips and metal shavings can fly. Clamp the door so it cannot spin on the bit, and keep fingers clear of the drill path.

Take doors off the cabinet before drilling when you can. A heavy door can fall while you work, and a stepladder is needed for high cabinets. Make sure it is stable, and ask a helper to hold the door.

If you drill near walls, be aware of wires or pipes behind cabinet backs. Unplug nearby power tools when changing bits.

Frequently asked questions

Are concealed hinges the same as soft close hinges?

No. Concealed describes where the hinge sits, hidden inside the cabinet. Soft close describes a damper that slows the last part of the swing. A concealed hinge may or may not have one.

Do I need special tools?

A power drill and a bit matching the cup size are the main needs. A drilling jig and a depth stop make the holes more accurate, and are worth using if you have many doors.

How many hinges does a door need?

Most small doors use two. Taller or heavier doors may need three or more, and the maker's instructions usually say how many to use for a given height.

Can I use the same hinges on face frame and frameless cabinets?

Only if the listing says so. Some hinges list both styles, while others list face frame only. The mounting plate often differs, so check before you buy.

Compare the products