Guide

What Gauge and Thickness Can Tin Snips Cut?

Most hand tin snips cut mild steel up to about 18 gauge, which is roughly 1.2 mm thick, and stainless steel up to about 22 gauge. A few models are rated to 16 gauge, and some lighter sets stop at 20 gauge. Always go by the rating for your exact snips and your exact metal.

Updated 2026-11-12 · Based on published specifications and maker information

Top picks from our best snips comparison

How gauge numbers work

Gauge is a thickness scale, and it runs backward. A lower number means thicker metal. So 16 gauge sheet is thicker than 18 gauge, and 18 gauge is thicker than 22 gauge.

Snip makers list a maximum gauge for each tool. That number is the thickest sheet the blades can cut without strain. Some listings give millimeters too. For example, the Amazon Basics set lists 18 gauge as 1.2 mm and 22 gauge as 0.8 mm. The gauge-to-thickness link also changes a little between metals, so the maker's rating for the material you are cutting matters most.

Think of the rating as a ceiling, not a target. Cutting a thinner sheet than the maximum gives cleaner cuts and puts less wear on your hands and on the blades.

What the published ratings show

Among the snips on our comparison page, the most common mild steel rating is 18 gauge. One model is rated to 16 gauge, and one set stops at 20 gauge. Stainless is harder to cut, so every listing that gives a stainless rating puts it at 22 gauge. You can see all of them side by side on our best snips page.

Here is how the listed specs compare. "Not listed" means the maker's data does not give that number.

ModelCut directionMild steel maxStainless maxListed weight
Midwest Bulldog MWT-6716BStraight, left and right (wide curves)16 gaNot listed0.85 lb
Amazon Basics 3-piece setStraight, left and right18 ga22 ga2.4 lb
HORUSDY 3-packStraight, left and right18 ga22 gaNot listed
Midwest ToughCut setStraight, left and right18 ga22 gaNot listed
Wiss M3RStraight, left and right18 gaNot listed0.75 lb
Midwest Blackout offset pairLeft and right18 gaNot listed1.96 lb
HURRICANE 3-piece setStraight, left and right20 ga22 ga1 lb

Mild steel, stainless and other metals

Mild steel is the usual reference metal for a snip rating. The listings above refer to cold-rolled steel, and the HORUSDY listing also gives the same 18 gauge limit for galvanized sheet.

Stainless steel is harder, so the safe thickness drops. A snip that handles 18 gauge mild steel is typically rated for 22 gauge stainless, which is a few steps thinner. If a listing gives no stainless rating, do not assume it can cut stainless at all.

Softer metals such as thin aluminum are generally easier to cut than steel of the same thickness, but the makers on our page do not publish separate aluminum ratings. When in doubt, treat the mild steel number as your upper limit and stay well under it.

Gutters, HVAC duct, flashing and roofing metal are the jobs these snips are built for. They are made for thin sheet, so they are not a good match for thick or hardened material.

What tin snips should not cut

Snip blades are made for sheet metal. Forcing them through the wrong material chips the edges and can loosen the pivot. One maker's listing says plainly to avoid hardened steel, rods and wire mesh, and that is good advice for any snip.

Skip these materials:

  • Sheet thicker than the rating, such as 14 gauge steel with a snip rated to 18 gauge
  • Hardened steel, rods, bolts and heavy wire
  • Wire mesh and fencing, which can nick the blades
  • Cardboard, fabric and fiberglass, which dull metal-cutting edges

How to cut near the limit safely

If your sheet is close to the rated gauge, a few habits make the cut easier and safer. Blade design helps too. Serrated blades grip the sheet so it does not slip, and drop-forged blades listed at 60 to 62 HRC, like the Midwest ToughCut set, are made to hold an edge.

Follow these steps:

  • Check the gauge of your sheet. If you are unsure, measure the thickness and compare it with the maker's mm figure.
  • Pick the right snip for the line. Use straight snips for long cuts and left or right snips for tight curves.
  • Open the jaws fully and cut with the middle of the blades, not the tips.
  • Make smooth, medium cuts and stop before the very end of each bite. Do not close the blades all the way every time.
  • Let the offcut curl away to the side instead of forcing it through the jaws.
  • Lock the latch when you are done so the blades stay protected.

When to use a different tool

If your metal is thicker than 16 gauge, hand snips are the wrong tool. Better options include electric shears, a nibbler or a cutoff wheel. Each has its own safety needs, so follow the maker's manual.

Handle length and weight matter on long cuts. The listed weights on our page run from 0.75 lb to 2.4 lb for the models above, so a lighter tool is easier on your wrist over a long run. Longer handles add leverage, which helps near the thickness limit. The Hurricane, HORUSDY and Midwest Blackout sets list 10 inch lengths.

A three-piece set covers straight cuts and both curve directions. A single snip is lighter to carry but locks you into one cutting direction.

Safety notes

Cut sheet metal edges are very sharp. Wear cut-resistant gloves and safety glasses, because small slivers can fly off during a cut. Do not hold the offcut with bare hands.

Deburr the edge with a file after cutting. Keep your free hand clear of the cutting path. Lock the latch before putting snips in a tool bag. If you work on a roof or ladder, secure your footing first, since a sudden release of the blades can throw you off balance.

Frequently asked questions

Can tin snips cut 14 gauge steel?

Not according to the published ratings on our page, where the thickest mild steel limit is 16 gauge. For 14 gauge, use a power tool made for thicker sheet.

Why is the stainless rating thinner than the mild steel rating?

Stainless is harder than mild steel, so the blades handle less thickness before they strain. That is why 18 gauge mild steel snips are usually rated to 22 gauge stainless.

Does a bigger snip cut thicker metal?

Longer handles give more leverage, but the rating is what counts. Two snips of similar size can have different limits, so read the gauge in the specs.

Can I cut galvanized sheet with tin snips?

Yes, if the maker says so. The HORUSDY listing gives an 18 gauge limit for galvanized sheet. Cut it with gloves on, because the edges are sharp.

Compare the products