What Are Spot Welders Used For? Uses, Types and When to Choose One
A spot welder joins two pieces of metal at a small point by pressing them together and passing a short, strong burst of electric current through them. Large versions build car bodies and sheet metal parts, while the compact battery spot welders we compare are used to weld nickel strips onto cells when building or repairing battery packs.
How a spot welder works
A spot welder uses resistance welding. Two electrodes squeeze the metal together, and a short pulse of current flows through the contact point. The metal resists the current, which makes heat, and a small spot melts and fuses the pieces.
The process needs no filler metal, no gas and no flame. That is why it is fast and clean, and why it suits thin sheet metal and thin strips. Thicker stock is harder to spot weld, because it needs far more current to heat all the way through.
Common uses for spot welding
Spot welding shows up wherever thin metal needs many quick, repeatable joints. Here are the most common jobs:
- Car body panels and frames in factories and auto body shops.
- Sheet metal parts such as brackets, enclosures and appliance housings.
- Welded wire mesh, such as baskets, racks and fencing panels.
- Battery packs, where nickel strips connect individual cells.
- Small repair work on thin steel or nickel parts.
Battery pack building: the DIY use
For hobbyists and small repair shops, battery packs are the main reason to buy a spot welder. Cells such as 18650, 21700 and LiFePO4 are joined with nickel strips to form packs for e-bikes, power tools and drones.
Spot welding is preferred here because it heats only a tiny area for a very short time. Soldering a cell holds heat on the case for longer, which can damage it. A spot weld gives a strong, low resistance joint with much less heat soaking into the cell.
The compact tools on our best spot welders page are all aimed at this job. They are not the large resistance welders used on car panels, which need high current mains supplies and are far bigger.
Battery welders versus industrial spot welders
The word spot welder covers very different machines. Check which kind you need before you compare features.
The table below sums up the difference.
| Type | Typical work | Power source | Size |
|---|---|---|---|
| Battery or capacitor spot welder | Nickel strips on battery cells | Built-in battery or mains | Compact, bench or handheld |
| Industrial resistance spot welder | Car panels, sheet metal fabrication | High current mains supply | Large, often fixed or on an arm |
What the specs mean for real work
If battery packs are your goal, a few specs matter most. Peak power and the thickest strip a welder handles tell you what it can join. For example, the AWithZ UK3 lists 13,800 W peak power and welds nickel up to 0.3mm, while the Seesii SE-402 lists 10,000 W and also 0.3mm.
Power levels let you match the weld to the strip. The Seesii SE-402 offers 25 levels, the UK3 offers 100, and the mains AWithZ P30C offers 999 with a listed peak of 21,800 W. More levels mean finer control, which helps when you move between thin and thicker strips.
Power source matters too. The UK3 and SE-402 run from a built-in battery, so you can work anywhere. The P30C and the AWithZ UF20B use mains capacitors, which suit a fixed bench. The UF20B lists 10,500 W and 99 levels, and its maker says it should stay connected to wall power while in use.
When to use a spot welder, and when not to
Use a spot welder when you are joining thin metal at points, repeating the same joint many times, or connecting battery cells without soaking them in heat. It is also a good fit when you want no gas, no filler and a quick result.
Skip it when you need a continuous seam, a watertight joint, or a weld on thick structural steel. Aluminum and copper are also hard to spot weld with small battery units, and one listing for the SE-402 notes they are not recommended. For those jobs, look at other welding methods.
Whichever you pick, do a test weld on scrap strip first. Aim for a full, even weld with no spatter and no burn-through.
Safety notes
Spot welding throws a short burst of very high current, so treat it with care. Wear safety glasses, because sparks and molten spatter can fly. Keep flammable materials away from the work area.
Lithium cells can overheat, swell or catch fire if shorted or damaged. Never let the welding pen touch both cell terminals at once, and weld on a non-conductive surface. Remove rings and metal jewelry before you start.
Mains capacitor welders connect to wall power, so keep cords and the foot pedal lead out of the work area and never open the case while it is plugged in.
Frequently asked questions
Can a spot welder weld two thick steel plates?
Small battery spot welders cannot. They are made for thin strips, and the units we compare list maximum strip thickness around 0.3mm for the models that state it. Thick plate needs a much larger industrial machine or another welding method.
Is spot welding better than soldering for battery cells?
For battery packs, many builders prefer it because it limits heat on the cell. Soldering keeps heat on the cell case longer, which can harm it.
Do I need a foot pedal?
Not always, but it helps. A pedal frees your hands to hold the cells and strip steady while you fire the weld. Several welders we compare include one.
Can I use a spot welder on aluminum?
Aluminum is difficult for small units because it conducts heat and current so well. One listing for the Seesii SE-402 says aluminum and copper are not recommended.
AWithZ UK3Best overall
Seesii SE-402Best cordless value
AWithZ P30CMost powerful