Should the Wax Ring Go on the Toilet or the Flange?
Put the wax ring on the toilet outlet (the horn) for most installs. It is easier to see, stays centered, and keeps the flange clear for lining up the bolts. Putting it on the flange also works and can help hold the bolts upright, as long as you set the toilet straight down without twisting.
The short version
Both methods make a good seal when done carefully. The difference is mostly about what is easier to control. The toilet is heavy and awkward, so the method that keeps your hands free and the ring centered tends to win.
Most people set the ring on the underside of the toilet. You turn the bowl upside down on a towel or cardboard, press the ring onto the outlet, then flip the toilet and lower it onto the flange. Some people prefer the flange because the ring helps hold the closet bolts still while they lower the bowl over them. Choose the one that fits your setup and stick with it.
Wax ring on the toilet: step by step
This is the usual approach, and it works with a standard ring or a wax-free seal. Check the instructions in the package first, since a few rubber seals specify which side they want against the toilet.
Before you start, shut off the water, flush, and drain the tank and bowl. Remove the old ring completely and scrape the flange clean.
- Lay the toilet on its side or upside down on a soft surface, with the outlet facing up.
- Press the ring evenly around the outlet. The flat, wide side goes against the porcelain. If the ring has a plastic funnel, the funnel points away from the toilet.
- Set the closet bolts in the flange slots, standing upright. Plastic retainer washers or the bolt cap kits can help them stay put.
- Lift the toilet with a helper, line the outlet up over the drain, and check that both bolts pass through the holes in the base.
- Lower it straight down. Do not slide, twist or rock it once it touches the ring.
- Press down with steady, even weight to compress the ring.
- Add washers and nuts, then tighten each side a little at a time.
When the flange is the better spot
Setting the ring on the flange has a real advantage. It keeps the ring in one place while you lower the toilet, and the ring can hold the bolts straight. If your bolts keep tipping over, that can make the job less frustrating.
The downside is visibility. With the toilet over the flange, you cannot see whether the ring stayed centered. A ring that drifts to one side can leave a gap. It is also easy to smear wax on the floor, so keep the area clean.
If you go this route, center the ring on the opening, press it down gently so it sticks, and set the toilet down in one motion. Do not lift it back up to check. A wax ring that has been compressed once is not reliable a second time, which matches what we say on our best toilet wax ring page.
Which way does the wax ring go?
With a plain ring, the orientation matters little. With a ring that has a funnel, plastic sleeve or flange, the direction matters more.
- Plain wax ring: either side can face down, though the flatter side usually goes against the toilet.
- Ring with a funnel or sleeve: the funnel points down into the drain pipe.
- Rubber or wax-free seal: follow the package. Many are made to go on the toilet outlet or on the flange, so the wording matters.
- Wax encased in rubber: the soft wax side faces the surface that needs to conform, and the instructions will say which.
Toilet or flange: a quick comparison
Here is how the two placements compare in practice.
| Factor | Ring on the toilet | Ring on the flange |
|---|---|---|
| Visibility | You can see it is centered | Hidden once the toilet is down |
| Bolts | Bolts can tip while you lower | Ring can help hold the bolts |
| Mess | Wax stays off the floor | Wax can smear on the floor |
| Best for | Most installs | When bolts will not stay upright |
Match the seal to your flange
The placement matters less if the seal does not fit your flange height. A recessed flange, for example tile that was laid after the flange was set, can leave a gap that a standard ring will not close. In that case you want an extra-thick ring or a stackable seal.
Our spec sheet lists how each seal fits. The Korky 6000BP is wax-free rubber, repositionable, and listed for flanges that sit above, level with or below the floor. The Fluidmaster 7530 is a stackable wax-free seal with brass bolts. The Hibbent kit is listed for level and below-floor flanges, and the Danco Perfect Seal is wax in a rubber casing that can be repositioned. For a wider look, compare them on our wax ring comparison.
If the toilet itself is the problem, such as a rocking base or a cracked bowl, a seal will not fix it. You may want to look at our toilet comparison before you rework the drain.
| Seal | Material | Repositionable | Flange fit |
|---|---|---|---|
| Korky 6000BP | Wax-free rubber | Yes | Above, level and below |
| Fluidmaster 7530 | Wax-free rubber | Yes | Stackable for recessed flanges |
| Hibbent extra thick kit | Polyurethane | Not listed | Level and below |
| Danco Perfect Seal | Wax and plastic | Yes | Not listed |
| iFealClear extra thick kit | Polyurethane | Not listed | Flush or slightly below |
Safety and common mistakes
A toilet is heavy and made of porcelain. Lift with a helper, bend your knees, and keep your fingers clear of the base when you set it down. Wear gloves, since the old ring and flange can be dirty.
Sewer gas can come out of an open drain, so stuff a rag in the pipe while the toilet is off. Pull it out before you set the toilet, and do not drop it down the line.
A few mistakes cause most leaks:
- Reusing an old ring or lifting the toilet after setting it.
- Overtightening the nuts, which can crack the base.
- Leaving the old wax on the flange.
- Using a standard ring on a recessed flange.
- Skipping new bolts when the old ones are rusty.
After you set it
Tighten the nuts evenly until the toilet is snug and does not rock. Stop there. Turn the water back on, let the tank fill, and flush a few times while watching the base for water. If you see leaks or the toilet shifts, you will need to pull it and start with a new seal.
Once it is dry, trim the bolts if needed, add the caps, and run a thin bead of caulk around the front and sides of the base if you like. Leave the back open if you want a leak to show.
Frequently asked questions
Can I use two wax rings stacked together?
It is sometimes done for slightly recessed flanges, but a single extra-thick ring or a stackable seal made for the job is usually more reliable.
How long do I wait before using the toilet?
Wax rings need no cure time. Check the package for a wax-free seal, and flush a few times to check for leaks before you walk away.
Do I need new bolts with a new ring?
Yes, if the old ones are rusty or bent. Several kits on our spec sheet include brass bolts, which resist rust.
What if the toilet rocks after tightening?
Do not keep cranking the nuts. Shim the base to level it, or pull the toilet and fix the flange height with a thicker seal.
Korky 6000BPBest overall
Fluidmaster 7530P8Best for tile floors
Hibbent 100-14.32TWaxringKit-0260-00Best extra-thick ring