Is a Thickness Planer Worth It for Woodworking?
A thickness planer is worth it if you plan to buy rough or reclaimed lumber, build projects that need parts of exactly the same thickness, or want to stop depending on whatever sizes the lumberyard stocks. If you only build a few small projects a year from pre-surfaced boards, you can probably skip it. The more you work with solid wood, the sooner a planer earns its bench space.
What a thickness planer actually does
A thickness planer shaves a board down to a consistent thickness. You feed the board in, rollers pull it under a spinning cutterhead, and the board comes out the other side flat on top and uniform in thickness from end to end. Then you flip it and repeat until it reaches the size you want.
One point trips up many beginners. A planer makes the two faces parallel to each other, but it does not flatten a warped board on its own. The machine presses the board flat while it cuts, then the board springs back. To correct a twist or cup, you first need one flat reference face, usually made with a jointer or a sled. After that, the planer does the rest.
When a planer is worth it
The case for a planer is strongest when you want control over your material. Rough lumber is usually sold in a more basic state than surfaced boards, and a planer lets you turn it into stock sized for your project. It also lets you rescue old barn wood, pallet boards and reclaimed beams that would otherwise be unusable.
- You build furniture, cabinets or boxes where parts must match in thickness.
- You buy rough or reclaimed lumber and want to surface it yourself.
- You resaw or glue up panels and need to level the result.
- You want to work in thicknesses that stores do not carry, such as thin drawer sides.
- You do woodworking regularly enough that a machine will see steady use.
When you can skip it
A planer is not for everyone. If you mostly build rough outdoor projects, shelves from construction lumber, or the occasional small item, a hand plane, sander or store-surfaced boards may serve you fine. A planer also takes real space. Benchtop models in our data weigh from 60 lb to about 91 lb, so you need a sturdy bench or stand and a spot to store it.
Think about dust and noise too. A planer throws out a lot of chips, so you will want a dust collector or a shop vac connected to the dust port. If your shop is small or shared, plan for both the machine and the cleanup before you commit.
What to look for if you decide to buy
Most hobby shops do best with a benchtop model. Our best thickness planer for the money page lays out the main choices on one spec sheet, and the best thickness planer page ranks the field more broadly. Here are the points that matter most.
Cutterhead type is the biggest split. Straight-knife heads cost less and cut well on straight-grained wood. Spiral heads use many small carbide inserts, run quieter and tend to leave a smoother surface on figured wood. Reversible knives and rotatable inserts help keep running costs down.
Width and thickness capacity come next. Most of the benchtop planers we list handle boards about 12.25 to 13 in wide and roughly 6 in thick. Check your widest board before you buy. Snipe control also matters. Snipe is a slightly deeper cut at the ends of a board, and carriage locks, anti-snipe designs and good infeed and outfeed support all reduce it.
How a few popular models compare
The table below pulls only from the published specs on our comparison page. It shows how different the options are in cutterhead style and weight, even when the width is similar. A blank spot means the spec was not listed.
If you want a two-speed feed for cleaner cuts in tricky grain, the DEWALT DW735 lists feed speeds of 96 or 179 cuts per inch. The Cutech 40800H lists an 8-position depth stop, which helps when you thickness a batch of boards to the same size. The DEWALT DW734 lists a four-column carriage lock aimed at reducing snipe.
| Model | Max width (in) | Cutterhead | Weight (lb) |
|---|---|---|---|
| CRAFTSMAN CMEW320 | 12.25 | 2 knives, reversible | 62.92 |
| DEWALT DW735 | 13 | 3 knives | 91.25 |
| DEWALT DW734 | 12.5 | 3 knives | 83.38 |
| Cutech 40800H | 13 | Spiral, 26 inserts | 69.2 |
| VEVOR 13-Inch Spiral | 13 | Spiral | 61.73 |
| WOODERS PL13-15AB | 13 | Dual blade | 60 |
Using a planer safely
A planer is a powerful machine with fast-spinning cutters and loud operation, so treat it with respect. Wear eye protection and hearing protection every time you run it, and a dust mask or respirator is smart because fine dust builds up quickly.
Follow these habits each session:
- Unplug the planer before you change knives, inserts or clear a jam.
- Check boards for nails, screws and staples, especially with reclaimed wood. Metal can damage the cutters and throw debris.
- Take light passes instead of forcing a deep cut.
- Stand to the side of the board, not directly in line with it, in case of kickback.
- Never reach into the planer while it is running, and keep hands away from the infeed and outfeed openings.
- Plug into a circuit that can handle the motor load, and avoid long thin extension cords.
The bottom line
If you want to move from assembling store-bought boards to making your own stock, a planer opens up a lot. It gives you precise thickness, access to rough and reclaimed lumber, and more freedom in your designs. If your projects are occasional and small, you can hold off and revisit the question once your needs grow.
When you are ready to shop, start with the value-focused comparison to match capacity, cutterhead and snipe control to the work you actually do.
Frequently asked questions
Do I need a jointer as well as a planer?
Not always. A jointer makes one board face flat, which a planer cannot do by itself on a warped board. Many hobbyists use a planer sled or buy lumber that is already close to flat instead.
Is a spiral cutterhead better than straight knives?
Spiral heads run quieter and tend to give a smoother finish in figured wood. Straight knives work well on straight-grained wood and can cost less, so the better choice depends on your lumber and budget.
Can I plane reclaimed wood?
Yes, but inspect it first. Remove all nails, screws and staples, and clean off dirt and grit, since these dull or chip cutters and can be unsafe.
Why does my planer leave deeper cuts at the board ends?
That is snipe. Support long boards on infeed and outfeed tables, feed steadily, and consider a model with a carriage lock or anti-snipe design to reduce it.
CRAFTSMAN CMEW320Best value overall
DEWALT DW735Best finish with knives
CUTECH 40800HBest spiral value