How to Use Sanding Discs on a Dremel
To use a sanding disc on a Dremel, press a hook and loop disc onto a small backing pad, slide the pad's shank into the collet, and tighten it. Then run the tool at a low speed and let the disc do the cutting with light pressure. Most rotary tool discs are about 2 inches across, so a 5-inch sander disc will not fit.
What you need before you start
Using a sanding disc on a rotary tool takes three parts: the tool itself, a backing pad with a shank, and the discs. The shank is the thin metal rod that goes into the tool. The backing pad is the round pad on the end of it, with a fuzzy loop surface that grips the disc.
Some discs come with the pad included. For example, the Rvetol 2 inch silicon carbide set on our best sanding discs page lists two backing pads, one with a 1/8 inch shank and one with a 1/4 inch shank, along with 240 hook and loop discs. If your discs do not include a pad, you will need to buy one separately.
Check your tool's collet size before you pick a shank. The collet is the part at the front that grips the accessory, and a shank only works if it matches the collet. Look in your tool's manual for the size.
- A rotary tool with a collet that matches your pad's shank
- A backing pad that uses hook and loop
- Hook and loop sanding discs sized for that pad
- Safety glasses and a dust mask
- A clamp or vise to hold small workpieces
How to attach a sanding disc, step by step
The process takes under a minute once you have done it a few times. Always unplug the tool first, or remove the battery if it is cordless. A tool that starts by accident while you are changing accessories can cause a cut.
- Unplug the tool or remove its battery, then let any spinning parts stop.
- Loosen the collet nut. Many tools have a shaft lock button you can hold down while you turn the nut.
- Slide the backing pad's shank into the collet. Push it in far enough that the pad sits close to the nose of the tool but does not touch it.
- Tighten the collet nut firmly. Give the pad a gentle tug to confirm it will not slip out.
- Center a disc on the pad and press it down with your thumb. The hooks on the pad grip the loop side of the disc, or the other way around, depending on the product.
- Plug the tool in, hold it away from your body, and run it briefly to check that the disc spins true and does not wobble.
Match the disc to your tool
The most common mistake is buying the wrong size. Sanding discs are sold for different tools, and they are not interchangeable. Our buying guide notes that most random orbital sanders take 5 inch discs, drywall sanders use 9 inch, and rotary tools use 2 inch.
A 5-inch disc is far larger than a rotary tool pad, and it would not spin safely on a small shank. If you want to sand with a Dremel, look for 2 inch discs with a hook and loop backing that matches your pad.
| Disc size | Typical tool | Fits a Dremel? |
|---|---|---|
| 2 inch | Rotary tools | Yes, with a matching backing pad |
| 5 inch | Random orbital sanders | No |
| 9 inch | Drywall sanders | No |
Choose the right grit and abrasive
Grit is the number printed on the disc. A low number means coarse and a high number means fine. Our buying guide says low grits like 40 and 60 remove material fast, grits from 120 to 240 smooth, and grits of 400 and up prepare a surface for finish.
Start with the finest grit that will do the job. If you begin too coarse, you will leave deep scratches that take extra passes to remove. Work up through the grits in order and do not skip more than one step at a time.
Abrasive matters too. Silicon carbide is used on the wet and dry set in our lineup, and it suits fine finishing work, including wet sanding. The Rvetol set runs from 80 to 5000 grit and is rated for both wet and dry use. Aluminum oxide is the common choice for general wood and metal work. Check that the maker states the material, since that tells you what the disc is built for.
Sanding technique and speed
Small discs spin quickly, so heat and gouging happen fast. Start at the lowest speed and raise it only if the disc is not cutting. Fast speeds can melt plastic, burn wood and wear out a disc early.
Hold the tool like a pencil and keep the disc nearly flat against the surface. Tilting it digs the edge in and leaves a groove. Use light pressure and keep the tool moving. Pressing hard does not speed things up. It just heats the disc and clogs it.
Check your progress often. Stop, wipe the dust away and look at the surface in good light. Dust packs into the abrasive and slows cutting, so replace a disc once it looks glazed or stops removing material.
- Clamp small parts so both hands stay on the tool.
- Move in slow, overlapping passes.
- Let the disc cool between long sessions.
- Swap to a fresh disc instead of pushing a worn one.
Safety notes
Sanding throws dust and small debris. Wear safety glasses every time, and use a dust mask or respirator, especially on metal, painted surfaces or old finishes. Sanding old paint can release harmful dust, so check what you are working on before you start.
Rotary tools can be loud over long sessions, so use hearing protection if the noise bothers you. Keep loose sleeves, long hair and jewelry away from the spinning disc. Never touch the disc while it is moving, and never change a disc with the tool plugged in.
Do not use a disc that is torn, bent or loose on its pad. A disc that comes off at speed can fly across the room.
Fixing common problems
If the disc keeps flying off, the hook and loop surfaces are probably worn, dirty or mismatched. Wipe dust from the pad, press the disc on firmly, or replace the pad. Make sure the disc backing is hook and loop, as our buying guide advises, since a disc that does not match your pad will not hold.
If the disc wobbles, the shank may not be seated in the collet, or the disc may be off center. Loosen the collet, reseat the shank and re-center the disc. A bent shank should be replaced.
If the disc clogs quickly, you are probably pressing too hard, running too slowly or using too fine a grit for the material. Some discs include anti-clog coatings or dust holes, which you can compare on our sanding disc comparison.
Frequently asked questions
Can I put a 5-inch sanding disc on a Dremel?
No. Five-inch discs are made for random orbital sanders. A rotary tool needs small discs, usually 2 inches, on a backing pad with a shank.
How do I know when to change a disc?
Change it when it looks smooth or glazed, when it stops cutting, or when it tears. Pushing harder on a worn disc only adds heat.
Can I wet sand with a rotary tool?
Only with discs rated for wet and dry use, such as silicon carbide ones. Keep water away from the tool body and any cord or battery contacts, and use light pressure.
Do I need dust holes on a small disc?
Not for most rotary tool work. Dust holes help when a sander has extraction. On a hand-held rotary tool, wear a mask and clean the disc as you go.
POTUINOM POTUINOM-SD5-165Best overall
3M 66584Net-backed dust control
Rvetol RVT003Most grits and discs