Guide

How to Use a Whetstone to Sharpen a Knife

Soak the stone if it is a water stone, set it on a stable base, and hold the blade at a steady angle of roughly 15 to 20 degrees. Push the edge across the stone in even strokes until a thin burr forms along the whole length, repeat on the other side, then move to a finer grit and finish with light strokes. The skill is consistency, not speed, and it gets easier with each session.

Updated 2026-11-12 · Based on published specifications and maker information

Top picks from our best whetstone comparison

What you need before you start

A whetstone is a flat block of abrasive. Sharpening on one removes a small amount of steel from both sides of the blade until the two sides meet in a fresh, keen edge. The process is simple, but a few supplies make it much smoother.

Most beginner kits bundle these items, and our best whetstone comparison shows which kits include which extras. At a minimum, gather the following:

  • A whetstone, ideally with a coarse side and a fine side
  • A non-slip base, rubber support or silicone holder so the stone stays put
  • A flattening stone, or a plan to buy one, to level the stone over time
  • An angle guide if you are new to holding a steady angle
  • A leather strop to clean up the burr at the end
  • A towel, a small bowl or spray bottle of water, and a dull knife to practice on

Choose the right grit

Grit is a number that describes how coarse the stone is. Low numbers cut fast and remove more metal. High numbers cut slowly and leave a smoother, more polished edge.

Our best whetstone page treats 400 as a low grit for repairing dull or damaged edges and 8000 as a high grit for refining and polishing. A 400 to 8000 range covers the full job, while a 1000 to 6000 stone handles routine upkeep but takes longer on a chipped edge. Many kits, such as the 400/1000 and 3000/8000 sets, put two grits on each stone, one per side.

Grit rangeTypical jobWhen to use it
400 (coarse)RepairChipped, damaged or very dull edges
1000 (medium)SharpenRegular dull knives after the coarse step
3000 (fine)RefineSmoothing the edge after the medium step
6000 to 8000 (very fine)PolishFinal finish on an already sharp edge

Prepare the stone and your station

Most whetstones sold for kitchen knives are water stones. Check the maker's instructions, because soaking times differ between products. Some listings call for 5 to 10 minutes, others for 10 to 15. A common sign the stone is ready is that bubbles stop rising from the surface. Do not soak a stone the maker says to use dry, such as a diamond plate sold for dry sharpening.

Place the stone in its base on a flat, stable surface. Put a damp towel under the base if it still shifts. A stone that slides is slow to work with and unsafe, since your hands are close to the blade.

Keep the surface wet while you work. The water carries away metal particles and keeps the stone cutting evenly. Add a few drops whenever the surface looks dry.

Sharpen the knife step by step

Start with the grit that matches your knife's condition. A badly dull or chipped knife begins on the coarse side. A knife that only needs a touch-up can start on the medium side.

Work on one side of the blade until you raise a burr, then switch sides:

  • Set the stone so the long side runs away from you. Hold the knife handle in your dominant hand and rest the fingers of your other hand flat on the blade, near the edge.
  • Tilt the spine up until the edge sits at about 15 to 20 degrees to the stone. Many Japanese-style knives use a shallower angle and many Western knives a slightly steeper one. If you are unsure, check your knife maker's guidance. An angle guide clipped to the spine helps you hold this angle.
  • Push the blade forward and across the stone as if you were trying to slice a thin layer off the top, leading with the edge. Cover the whole edge from heel to tip, using light, even pressure.
  • Repeat the stroke 10 to 15 times, then run a fingertip gently across the opposite side of the edge, never along it. You are feeling for a burr, a thin ridge of metal that curls toward the side you are not working.
  • Once the burr runs the full length, flip the knife and work the other side the same way until a burr forms on the first side.
  • Move to the next finer grit and repeat with lighter pressure and fewer strokes. Each step removes the scratches left by the one before.

Remove the burr and test the edge

The burr is a sign you have reached the edge, but it is not part of the final sharpness. Left in place, it folds over and the knife feels dull again after a few cuts.

To remove it, make a few alternating light strokes on your finest stone, using less pressure each time. Then draw the blade, edge trailing, across a leather strop on each side. Some kits include a strop for exactly this purpose. Using a polishing compound on it is optional.

Wipe the knife clean and test it on something soft, such as a ripe tomato or a sheet of paper held up in the air. A sharp edge should slice cleanly without pressing hard. If it skips or tears, go back to the medium grit and look for a spot where the burr never formed.

Rinse and dry the knife before use, since fine metal slurry can cling to the blade.

Keep the stone flat and avoid common mistakes

Whetstones wear into a dish with use. A dished stone gives uneven edges, and it is the reason a flattening stone matters. Rub the stone against the flattener with some water until the surface is level again. If your kit does not include one, buy a separate flattener. Doing this before each session keeps results predictable.

Most trouble comes from a handful of habits. Changing the angle mid-stroke rounds the edge. Pressing too hard clogs the stone and wears it faster. Skipping the burr check means one side may never reach the edge. Jumping to a fine grit on a very dull knife wastes time, because fine stones remove metal slowly.

Let the stone dry fully in the open air before storing it, and keep it away from hard impacts, since stones can crack.

Safety notes

Always cut away from your fingers and keep your guiding hand flat on the blade, never wrapped around the edge. Check the burr by touching across the edge, not along it. Place the stone on a stable base and keep the work area clear and well lit.

Wear safety glasses if you are using a diamond plate or any dry-use abrasive, since fine particles can become airborne. Do not leave a wet stone on a polished surface that water can damage. Keep sharp tools out of reach of children when you are finished.

Frequently asked questions

How often should I sharpen my kitchen knife?

It depends on how much you cook and what you cut on. Sharpen when the knife starts to crush tomatoes or slip off onion skin instead of biting in. Light touch-ups on a fine grit are quicker than full sharpening.

Do I need oil on my whetstone?

Not for water stones. Some product listings state that water is all you need. Oil stones are a different type and follow their own instructions, so check what your stone is made for.

Can I use a whetstone on serrated knives?

Usually not with a flat stone. Serrated edges have scallops that a flat stone cannot reach well. Look for a tool made for serrations or a sharpening service.

Is an angle guide worth using?

For a beginner, yes. It helps you hold a steady angle while your hands learn the motion. Many people drop it once they can hold the angle by feel.

Which stone should I start with if I only want one?

A combination stone with a medium and a fine side, such as a 1000/3000 stone, covers regular upkeep. If your knives are chipped or very dull, a coarser stone helps you repair the edge first.

Compare the products