How to Use a Thickness Planer Safely and Correctly
To use a thickness planer, start with a board that has one flat face, set a shallow depth of cut, and feed the board in with the grain while you stand to the side. Repeat light passes, flipping the board now and then, until you reach your target thickness. Wear eye, ear and lung protection, and unplug the machine before you touch the cutterhead or change knives.
What a thickness planer does (and does not do)
A thickness planer makes the top face of a board parallel to the bottom face. Rollers pull the board under a spinning cutterhead, and the cutterhead shaves a thin layer off the top. The result is a board of even thickness from end to end.
It does not flatten a warped board on its own. The rollers press a cupped or twisted board flat as it goes through, and the board springs back afterward. To get a truly flat face, you first need a jointer or a sled (more on that below). Think of the planer as the tool that sets thickness, not the tool that creates the first flat face.
Safety first: gear and habits
A planer is loud, throws chips and can kick a board back. Most of the risk comes from skipping simple habits, so set them up before the first cut.
- Wear safety glasses or a face shield every time the motor runs.
- Wear hearing protection. Planers are loud, and a vacuum running beside one adds to the noise.
- Wear a dust mask or respirator. Fine wood dust is bad for your lungs, and hardwood dust is worse.
- Unplug the planer before you change knives or inserts, clear a jam or reach near the cutterhead.
- Skip loose sleeves, gloves, jewelry and dangling cords.
- Stand to the side of the infeed, not directly behind the board, in case it kicks back.
- Keep your hands on the top of the board and well away from the opening. Never reach into the machine while it runs.
- Check for nails, screws and staples. Metal can chip a knife and send fragments flying.
Prepare the board and the machine
Start by checking the board. Reclaimed lumber, pallet wood and anything with hidden hardware is a risk, so inspect it closely or skip it. Loose knots can also fly out, so avoid boards with them. Dirt and grit dull knives quickly, so brush off or wipe the surface first.
Next, confirm the board fits the machine. Most benchtop models on our spec sheet handle boards up to 13 in wide and 6 in thick, so measure your widest and tallest pieces. Check the minimum board length in your manual too. For example, the floor-standing Jet lists a 6-3/4 in minimum, and short pieces can stall or get thrown.
Then set up the machine itself:
- Place a benchtop planer on a stable, level surface and secure it as the manual describes.
- Leave plenty of clear space in front of the infeed and behind the outfeed. A long board needs support at both ends.
- Connect a dust collector or shop vacuum to the dust port. Many models list a port, and some accept more than one hose size.
- Raise any extension tables or roller supports so they sit level with the machine bed.
How to plane a board, step by step
Work slowly the first few times. A calm, repeatable routine matters more than speed.
- Make one face flat first. Use a jointer, or tape or shim the board onto a flat sled so it cannot rock.
- Check the grain direction. Feed the board so the cutterhead cuts with the grain, which usually means the rising grain faces away from you as it enters.
- Set the depth of cut using the height crank and the depth indicator. Start with a very light pass, and follow the maximum depth listed in your manual.
- Choose the feed speed if your machine has two. A slower rate gives a finer finish. The Cutech and WEN, for example, list 16 fpm on low speed.
- Turn on the machine and let the cutterhead reach full speed.
- Feed the board in square and flat on the bed until the rollers grab it. Let the machine pull it through. Do not push hard.
- Support the board as it exits, especially a long one, and let it clear completely before you stop.
- Lower the cutterhead a small amount and repeat. Flip the board end for end between passes if the surface is uneven.
- When the board is close to final thickness, take one more very light pass on each face for a clean finish. Turn the board over between passes so you remove material evenly from both faces.
Avoid snipe and tearout
Snipe is a shallow dip near the start or end of a board. It often appears when the board is not supported well as it enters and leaves the rollers. Some machines are designed to reduce it. The Cutech credits four lead screws, and the DEWALT DW734 lists a four-column carriage lock. Good design helps, but good technique matters more.
Here are habits that reduce snipe: support long boards level at both ends, feed boards end to end in a continuous line so the rollers never release one board before the next arrives, and plane a few extra inches of length, then cut the ends off.
Tearout happens when the knives lift grain instead of slicing it. Figured or curly wood is the usual culprit. Take a lighter pass, use the slower feed speed, and check the grain direction. Sharp knives matter too. Makers say spiral cutterheads, which use many small staggered cutters, cut more quietly and reduce tearout, but a dull insert will still leave a rough surface.
Quick troubleshooting guide
If a board comes out looking wrong, this table points to the usual cause.
| Problem | Likely cause | What to try |
|---|---|---|
| Dip at board ends | Snipe from poor support | Add extension support, chain boards end to end, leave extra length |
| Rough or chipped grain | Cut too deep or against the grain | Take a lighter pass, flip the board, slow the feed rate |
| Lines running along the board | Nicked knife or insert | Rotate or replace the knife or insert, unplugged |
| Board stalls or slows | Cut too deep or board too short | Raise the cutterhead and take a lighter pass |
| Board comes out tapered | Uneven face or poor support | Flatten one face first and support the board evenly |
| Chips pile up inside | Weak dust collection | Connect a vacuum and clear the port before each session |
Keep the planer in good shape
A little upkeep keeps cuts clean and safe. Unplug the machine, then brush out chips and wipe the bed. Check the knives or inserts for nicks. Rotate or replace them when the finish gets rough, following your manual. Straight-knife heads like the DEWALT DW735's three-knife cutterhead are listed as easier to change, while spiral heads let you rotate individual inserts.
If you are still shopping, our best thickness planer page puts width, thickness, cutterhead type and weight on one spec sheet. If you want a solid machine without extra features, see the best thickness planer for the money comparison. Whichever you choose, read the manual first, because depth limits and setup steps vary by model.
Frequently asked questions
Can I plane a board that is not flat?
Not directly. The rollers flatten a bowed board as it passes through, and it springs back afterward. Flatten one face on a jointer or a sled first, then plane the other face parallel to it.
Why does the planer leave ridges?
Ridges usually come from a nicked knife or insert, or from a cut that is too aggressive for the wood. Replace or rotate the cutters with the machine unplugged, and take lighter passes.
Do I need a dust collector?
Yes, plan on some form of dust collection. A planer produces a lot of chips fast, and a vacuum or collector connected to the dust port keeps the machine from clogging and reduces the dust you breathe.
Can I plane very thin pieces?
Often not safely. Every machine lists a minimum thickness and length. Thin or short pieces can crack, stall or get thrown, so check your manual and use a carrier board if it allows it.
Which direction should I feed the board?
Feed it so the knives cut with the grain, not against it. If the surface tears, flip the board end for end and try again with a lighter pass.
CUTECH 40800HBest overall
WEN PL1337Spiral head with warranty
DEWALT DW735Easiest knife changes