Guide

How to Use a Speed Square for Rafters and Birdsmouth Cuts

Yes, a speed square can lay out rafters. Set its pivot point on the edge of the board, rotate the square until the roof pitch number lines up with that edge, and scribe the plumb cut along the square. Then use the square's 90° edge to mark the level seat cut and the plumb cut that form the birdsmouth.

Updated 2026-11-12 · Based on published specifications and maker information

Top picks from our best speed square comparison

What a speed square does for rafters

A speed square is a right triangle with a lipped edge, called the heel or fence, that hooks over the edge of a board. Along the long edge is a degree scale. At the pivot corner, you can rotate the square against the board and read the angle you want.

For rafters, the useful marks are the pitch scale and the pivot point. Pitch is how many inches the roof rises for every 12 in of horizontal run. A 6 in 12 roof, for example, is a gentle slope of about 26.6°. The square turns that number into a line you can draw without doing any trig.

The same square also works as a try square for 90° marks, a miter square for 45° marks, and a saw guide. You will use several of those roles when you cut the birdsmouth.

Our best speed square page compares squares by blade length, weight, and roof layout features. Check it if yours lacks a pivot point or rafter scale.

What to gather before you start

Good layout starts with good prep. Rafters are long, and a small error at the first mark repeats on every board in the roof.

Here is a simple checklist:

  • A speed square with a pivot point and a common rafter scale
  • A sharp pencil, or a knife if you want a finer line
  • Straight rafter stock, with the crowned edge turned up
  • Your roof pitch, written as rise per 12 in of run
  • The width of the wall top plate where the rafter will bear
  • A tape measure and a scrap board for a test rafter

Marking a common rafter step by step

A common rafter runs from the wall straight up to the ridge. Always make one pattern rafter first, check it in place, then trace it onto the rest.

Here is the pivot method for the plumb cut at the ridge end:

  • Lay the rafter board on edge on sawhorses, crown up.
  • Set the heel of the square against the top edge of the board.
  • Place the pivot point on that top edge at the spot where the plumb cut will start.
  • Hold the pivot point in place and rotate the square until the pitch number on the common scale lines up with the same board edge. For a 6 in 12 roof, line up the 6.
  • Draw along the square's straight edge. That line is the plumb cut, which sits vertical once the rafter is installed.
  • Measure the rafter length along the top edge, using a rafter table or guide book, and mark the second plumb line at the wall end the same way.

Laying out the birdsmouth

A birdsmouth is the notch that lets the rafter sit flat on the wall's top plate. It has two faces. The seat cut is level and rests on top of the plate. The plumb cut is vertical and faces the outside of the wall.

Start at the plumb line you scribed for the wall end. Slide the square so its edge lies along that line. Use the 90° edge to draw the seat line from the plumb line back toward the rafter, square to the plumb cut. Mark the seat so its length equals the width of your top plate.

Next, check the depth of the notch. Many building codes limit how much of the rafter depth you may remove at the bearing point, and a common rule is about one quarter. Confirm the exact limit with your local code, because cutting too deep weakens the board where it carries load.

Scribe notches can help here. Draw a line a set distance from the board edge, then compare it to the depth you plan to cut. Cut your pattern rafter, set it in place, and check that the seat sits flat and the plumb cut is vertical before you cut the rest.

Which squares suit rafter layout

Not every speed square is equally helpful on a roof. The pivot method needs a pivot point, and the pitch scale makes it fast. Rafter tables or a guide book help you find lengths and handle hip and valley rafters.

Here is how the squares on our lineup compare, based on their listed specs. For the full side-by-side, see our speed square comparison.

SquarePivot pointRafter tablesWeight
Swanson S0101, 7 inListedListed8 oz
Swanson Speedlite, 8 inNot listedNot listed4.48 oz
Spec Ops Elite Fury, 7.5 inNot listedNot listed9.6 oz
Swanson 2-pc kit, 7 inListedListed12.8 oz
Klein Trim & Rafter kit, 7 inNot listed (preset angle guide)Not listed11 oz

Safety and common mistakes

Roof framing involves sharp tools, heavy lumber, and heights. Take the safety steps seriously before you cut anything.

Keep these points in mind:

  • Wear safety glasses and hearing protection when you run a circular saw.
  • Clamp or brace the rafter so it cannot shift as you cut.
  • Keep your hands behind the blade path and let the blade stop before you lift the saw.
  • Unplug a corded saw before changing a blade.
  • Use fall protection and a stable ladder when you test-fit rafters at the wall.
  • Do not use a plastic square as a saw guide for repeated cuts, since a blade can bite into it.
  • Cut on the waste side of your line so the finished notch matches the mark.

Frequently asked questions

Does a speed square give me the rafter length?

Not by itself. The square marks angles. For length, you need the run of the roof and a rafter table or guide book, which give length per foot of run. Measure the pattern rafter and test it in place.

Can I use a speed square for hip and valley rafters?

Yes, if it has a hip and valley scale. You use the pivot method in the same way, but read the hip and valley row instead of the common row. Those rafters also need side cuts, so follow a guide.

Why make a pattern rafter first?

A pattern rafter lets you check pitch, length, and the birdsmouth fit before you cut the rest. Once it fits, you trace it onto the other boards, so any error is caught early instead of repeated.

Do I need a level vial on the square?

No. A level vial is a convenience for checking plumb and level, but the pivot point and pitch scale do the layout. Pick a vial only if you will use it often.

Compare the products