How to Use a Laser Level to Hang a TV
Set the laser on a tripod or a stable surface, let it self-level, and project a horizontal line at the height of your mount's mounting holes. Find the studs first, mark each hole where it crosses the beam, drill pilot holes, then fasten the mount. A basic cross line laser is enough for this job.
What the laser does and does not do
A laser level gives you a straight, level reference line across the wall. That line replaces a bubble level held against a bracket, which is easy to tilt by accident. It makes sure the two sides of your TV mount sit at the same height.
It does not find studs, check wall type or hold the weight of the TV. Those jobs belong to a stud finder and the mount's hardware, so plan for both before you pick up the laser.
Which laser level you need
For a single wall, a cross line laser is plenty. It throws one horizontal and one vertical beam, which suits pictures, shelves and tile on one wall, and a TV mount falls in the same category. Full-room layouts such as 3x360 and 4x360 are built for projects that wrap around a room, so they add little here. Our best laser level comparison lists these layouts next to each other if you want to see the differences.
Green beams are brighter than red, which helps in a lit living room. Look at accuracy at 33 ft, too. One cross line model on our page, the Motovera LL-T2, lists 0.11 in at 33 ft, a 4° self-leveling range and a tripod in the box. Across a TV-sized span, that kind of figure is far tighter than you can drill.
Gather your tools
Most of this is already in a basic toolbox. Check that the laser's batteries are fresh before you start, since a dim beam is harder to read.
- Laser level, with a tripod or a stable shelf or stool to rest it on
- Stud finder
- Painter's tape and a pencil
- Tape measure
- Drill and bits that match your mount's hardware
- Socket wrench or driver for the lag bolts
- Standard level, for a final check
- Safety glasses
- A helper for lifting the TV
Step by step: marking and mounting
Work slowly through the marking stage. Mistakes there are the ones you see on the wall afterward.
- Choose the TV height. Many people aim to have the center of the screen at eye level when seated. Sit where you normally watch and have a helper hold a piece of tape on the wall for a rough spot.
- Find the studs. Scan the wall, mark both edges of each stud, then mark the center. Most mounts need to be anchored into at least one or two studs, so follow the bracket's instructions.
- Check behind the wall. Wiring and pipes sometimes run vertically from outlets and switches, so avoid drilling directly above or below them.
- Set up the laser. Place it on the tripod or a steady surface a few feet from the wall, unlock the pendulum if it has one, and let it settle. If it flashes or beeps, it is outside its self-leveling range, so adjust the surface until it stops.
- Aim the horizontal line. Hold the mount's template or bracket against the wall and slide the laser's beam until it runs through the mounting holes on both sides. Mark the center of the line with painter's tape.
- Mark the holes. Where the beam crosses a stud, mark the hole position with a pencil. Use the vertical beam to center the bracket on the wall, if you want a centered TV.
- Drill pilot holes. Use the bit size the mount's instructions call for, and keep the drill straight.
- Fasten the mount. Tighten the bolts firmly but do not overtighten. Check with a standard level before the TV goes on.
- Hang the TV. Lift it with a helper and engage the mount as directed.
Choosing a layout for the job
Different laser layouts handle this task with different levels of effort. The table below uses the layout descriptions from our comparison page.
| Layout | Beams | Fit for a TV mount |
|---|---|---|
| Cross line | One horizontal, one vertical | Good fit. Covers height and centering on one wall. |
| 3x360 | One horizontal and two vertical full planes | Works, but extra beams are rarely needed. |
| 4x360 | Adds a second horizontal plane | Better for a whole room. Overkill for one wall. |
Safety and common mistakes
Never look into the beam or point it at anyone's eyes. Most lasers in this class are low power, but bright light can still be uncomfortable and a distraction. Wear safety glasses when you drill, because dust and chips can fly.
TVs are heavy and awkward. Lift with a helper and use a stable step stool for any reach above your shoulder, rather than leaning from a chair. Turn off power to the area if you are unsure about wiring behind the drilling spot.
A few errors come up often. Do not trust a beam when the laser is not level, so wait for it to settle. Do not move the tool after you have started marking. Read the center of the line each time, not the edge. If the line looks broken or thick, step closer or switch to a darker spot on the wall. Magnetic brackets only hold on metal surfaces, so for a drywall job use a tripod or rest the tool on a stable surface instead. For more on features worth comparing, see our laser level buying guide.
Final checks
Before you mount the TV, hold your standard level on the bracket and confirm it reads level. The laser got you close, and the bubble is a quick second opinion. Pull on the mount firmly to confirm it feels solid.
Once the TV is up, step back and look at it from the couch. If it is a hair off, most mounts have small adjustment slots that let you tilt it slightly, so loosen and correct before you finish tightening.
Frequently asked questions
Do I need a green laser to hang a TV?
No. A red beam works indoors in most rooms. Green is brighter, so it is easier to see in a sunny room, which can help with marking.
Can I use a laser level without a tripod?
Yes, if you have a flat, steady surface at about the right height. Check that the tool settles and stops flashing before you mark anything.
What if my laser keeps flashing or beeping?
It usually means the surface is tilted beyond the self-leveling range. Some models list a range of 3° to 5°. Move the tool to flatter ground or shim it until it stops.
Is the laser line accurate enough over a short distance?
Yes. Accuracy figures are listed at 33 ft, and a TV mount spans only a few feet, so any drift is much smaller than the width of a pencil mark.
Huepar hm03cg-ls04cgBest overall
VEVOR LRE203Longest range, large sites
Motovera LL-T2Tripod-ready cross line