How to Sand Wood With an Electric Sander
To sand wood with an electric sander, clamp the piece down, start with a coarse grit such as 80 to 120 to level the surface, then work up through 150 or 180 to 220 grit, skipping no more than one grit at a time. Keep the sander flat and moving, let the tool do the cutting, and wipe away dust between grits. Wear eye, hearing and dust protection the whole time.
Match the sander to the job
Electric sanders come in a few common types, and each one suits different work. A random orbital sander uses round discs and works well on flat boards and tabletops. A palm or sheet sander uses cut sheets of paper and fits small projects and tighter spots. A belt sander removes wood fast, but it is easy to gouge with, so it is best left for rough stock removal.
Your sander decides what paper you buy, so check the pad size and how the paper attaches (clamps, hook and loop, or peel and stick) before you shop. Our best sandpaper for wood comparison lists sheet sizes and pack contents side by side, which makes it easier to find paper that fits.
| Sander type | Best for | Paper format |
|---|---|---|
| Random orbital | Flat boards, tabletops, general smoothing | Round discs, usually hook and loop |
| Palm or sheet sander | Small projects, furniture parts, light jobs | Quarter sheets or cut-down full sheets |
| Detail or block sander | Corners, edges and small areas | Strips or small cut pieces |
| Belt sander | Fast removal on rough or thick stock | Sanding belts |
Choose paper sizes that fit
Sheet paper is sold in a few standard sizes. Full sheets of 11 × 9 inches can be cut down to fit most sheet sanders. Quarter sheets of 5.5 × 4.5 inches suit palm sanders and blocks. Strips of 9 × 3.6 inches fit blocks and some sheet sanders.
Product listings often say which tools they work with. For example, the Shineboc assortment is 9 × 3.6 inches and lists use with sanding blocks, palm sanders and sheet sanders. The Aceple and BOSHCRAFT packs are 5.5 × 4.5 inch quarter sheets that list block and palm sander use. Always compare the sheet to your own sander's pad before you buy.
Plan your grit sequence
Sanding works in stages. Coarse grits shape the wood and remove old finish. Middle grits remove the scratches the coarse paper left. Fine grits leave a surface ready for stain, oil or paint.
The reliable rule is to move up one step at a time. The 3M listing advises skipping no more than one grit in a sequence. Jump too far and the finer paper cannot erase the deeper scratches, and they show up under the finish.
- 80 to 120 grit: shape the wood, level joints or strip old finish.
- 150 or 180 grit: remove the scratches from the first stage.
- 220 grit: final smoothing before finish.
- Skip finer grits unless your finish calls for them. Bare wood rarely needs more than 220 grit.
Set up and stay safe
Good prep makes the sanding easier. Clamp the workpiece so it cannot move, or place it on a non-slip mat. Check the wood for nails, staples and screws, because metal will tear the paper and can damage the pad. Attach fresh paper and make sure it sits flat and centered, with any dust holes lined up.
Sanding is loud and dusty, so protect yourself before you switch on the tool.
- Wear safety glasses to keep dust and flying chips out of your eyes.
- Wear hearing protection, since sanders can be loud over long sessions.
- Wear a dust mask or respirator rated for fine dust. Wood dust is a respiratory irritant.
- Keep the power cord behind you and away from the pad, and unplug the sander before changing paper.
- Sand in a ventilated space, and be careful with old paint, which may contain lead if the piece is very old.
Sand the wood step by step
Once you are set up, the technique is simple. The main goal is steady, even contact so you do not dig into the surface.
Follow these steps for each grit:
- Place the sander flat on the wood before you turn it on. Starting with the pad in the air can leave a divot.
- Turn it on and let it reach full speed, then move it slowly along the grain in overlapping passes.
- Use light pressure. Pressing hard slows the motor, heats the paper and leaves swirl marks.
- Keep the sander moving and keep the pad flat. Tilting it rounds over edges and corners.
- Lift the sander off the wood before you switch it off, and let it stop spinning first.
- Vacuum or wipe the surface, then change to the next grit and repeat.
Handle dust, clogging and tricky spots
Paper clogs when dust packs between the grit particles. A clogged sheet stops cutting and starts burnishing the wood. Some papers add an anti-clog coating to slow this down, and several of the listings on our best sandpaper for wood page mention one. Whatever paper you use, replace it once it looks glazed or stops removing wood.
Edges and corners need a gentler touch. Power sanders can round them over quickly, so ease off near the edge and finish those spots by hand with a block. A small detail block, like the one that comes with the MAXMAN assortment, can reach areas a full-size pad cannot.
Always follow the direction of the grain for the last grit. Sanding across the grain leaves scratches that are easy to see once stain goes on.
Check the surface before you finish
When you reach your final grit, wipe the wood with a clean, dry cloth or a tack cloth to pick up fine dust. Then look at the surface at a low angle under good light. Scratches, dull patches and swirl marks show up best this way.
A light mist of water or a wipe with mineral spirits can also reveal scratches, because it briefly shows how the wood will look with a finish on. If you spot a problem, go back one grit, sand the area, and work forward again.
If you plan to wet sand, only use paper marked for wet and dry use. Several silicon carbide assortments on our comparison page are labeled that way. Keep water well away from the electric tool itself, and use wet sanding by hand only.
Frequently asked questions
Should I sand with the grain or across it?
Sand with the grain, especially on your last grits. A random orbital sander hides scratches better than a hand block, but the final pass should still follow the grain.
How do I know when to move to a finer grit?
Move up when the surface looks uniform and the scratches from the previous grit are gone. If you can still see deep marks from the coarse paper, stay on the current grit a little longer.
Can I reuse sandpaper on my sander?
You can use a sheet until it clogs or wears smooth. Tapping it clean can extend its life, but once it stops cutting, replace it to avoid heat and burnish marks.
Do I need to sand between coats of finish?
Many finishes benefit from a light sanding between coats to smooth raised grain. Check your finish's instructions, and use a fine grit and light pressure so you do not cut through the coat.
Shineboc 23CMSZ-CoarseMixBest overall
Pihemum 45PXSZZHWidest grit range
3M 9000NASimple 220 finishing refill