How to Sand Wood Floors: Sandpaper Amount and Process
Sand a wood floor in three passes, such as 36, 60 and 80 to 100 grit on a rented drum or orbital floor sander, and finish edges and corners by hand. There is no single sheet count that fits every floor, so buy belts or discs for each grit based on your room size and plan a few spares. Skip no more than one grit step between passes so scratches from the earlier grit do not show up under the finish.
Floor sanders use belts and discs, not loose sheets
The word sandpaper covers two different jobs on a floor project. The big machine uses sanding belts or discs sized for that specific model. The sheets you hold in your hand are for the places the machine cannot reach, such as corners, stair edges and door thresholds.
Before you buy anything, check which sander you are using and which abrasive size it takes. Rental shops usually stock the right belts and discs for their machines, so ask what fits. Buy hand sheets separately for the detail work.
This matters for the question of how much sandpaper to buy. You are really planning two small shopping lists: machine abrasives for the field of the floor, and hand sheets for the edges.
Pick your grit sequence
Floor sanding works in stages. The coarse pass flattens the boards and removes old finish. The middle pass removes the scratches from the first one. The final pass leaves a surface the finish can bond to evenly.
The exact starting grit depends on the floor. Heavily worn or coated floors start coarser, and bare, fairly flat boards can start finer. The table shows a common pattern.
- Skipping no more than one grit step is the safe rule. Our best sandpaper for wood page notes the same advice from the 3M listing.
- Jumping from very coarse to very fine leaves deep scratches that fine paper cannot remove.
- Hand sheets for edges should match the grit the machine is using on that pass, so the edge and the field blend together.
| Pass | Typical grit | What it does |
|---|---|---|
| First (coarse) | 36, or 24 for very rough floors | Levels boards and strips old finish |
| Second (medium) | 60 | Removes scratches from the first pass |
| Third (fine) | 80 to 100 | Smooths the surface for stain or finish |
| Optional final | 100 to 120 | Extra smoothness on a screen or buffer |
How much sandpaper do you need?
Exact quantities depend on the species, the finish being removed and how flat the floor is. Hard, thick old finish uses up abrasive faster than bare wood. For that reason, no honest formula works for every room.
A practical way to plan is to think in passes. You will make at least three passes over the whole floor, and each pass needs fresh abrasive in the right grit. Start with one belt or disc per grit for each room you are sanding, then add spares for the coarse grit, where abrasive wears out fastest.
Replace the abrasive when it stops cutting. If you have to push harder, or the paper looks smooth and glazed, it is done. Pushing a worn belt makes heat and burnishes the wood instead of leveling it.
Ask the rental shop whether you can return unopened belts and discs. That lets you buy a little extra without waste.
For hand sanding, a mixed pack is the easiest way to cover every grit. Several of the sets in our comparison cover the whole range from 80 up to finer grits, so you do not have to buy one grit at a time.
The sanding process, step by step
Work in a calm order, and finish each stage fully before you move to a finer grit.
- Prepare the room. Clear the furniture, remove shoe molding if you can, and set any exposed nail heads below the surface so they do not tear the paper.
- Make test passes. Practice on a small area, or in a closet, to get a feel for the machine.
- Sand with the coarse grit. Move steadily along the grain and keep the machine moving, because stopping in one spot leaves a dip.
- Edge the floor. Use an edger with the same grit along the walls, then switch to hand sheets for corners.
- Vacuum thoroughly between grits. Grit left on the floor can scratch the surface during the next pass.
- Repeat with the medium grit, then the fine grit, using the same method each time.
- Check the result. Wipe the floor with a clean cloth and look at it from a low angle with good light. Scratches and missed spots show up best this way.
- Clean up completely before staining or finishing. Dust left on the floor will end up in the finish.
Hand sheets for edges and corners
Corners and edges are where hand sheets earn their place. Full 11 × 9 in sheets can be folded or cut down, while quarter sheets at 5.5 × 4.5 in are easier to wrap around a block.
The large-sheet option on our best sandpaper for wood page includes 25 sheets in 80, 120 and 220 grit. The Aceple quarter-sheet pack lists 52 sheets in six grits from 80 to 400, which works well on a block for small areas. If you want printed grit numbers on the back so you can tell sheets apart quickly, the Boshcraft pack lists 50 quarter sheets in six grits from 80 to 400 with the number marked.
For the very last smoothing step on edges, a 220 grit sheet works well. The 3M general purpose pack lists five 11 × 9 in sheets in 220 aluminum oxide, which is enough for light finishing by hand. Always sand with the grain, and keep your grit order matched to the machine.
Safety notes
Floor sanding is noisy and dusty, so protect yourself before you start.
Wear hearing protection and a dust mask or respirator rated for fine dust. Add safety glasses, since stray grit and debris can fly up. Wood dust from old floors can also contain old paint or finish, so ventilate the room and keep dust off your skin.
Check that the power cord is in good condition and plugged into a properly rated outlet. Route the cord behind you and over your shoulder so the sander never crosses it. Unplug the machine before changing a belt or disc.
Fine dust can ignite near a spark or flame. Turn off pilot lights and avoid open flames while sanding, and empty the dust bag outdoors when it fills. Machines are heavy and can pull sideways, so keep a firm grip and lower the drum slowly onto the floor.
Frequently asked questions
Can I sand a wood floor with just a handheld sander?
You can on a very small area, but it takes much longer and is harder to keep level on a full room. A rented floor sander is the usual choice for large areas, with handheld tools for edges.
Do I need to sand every time I refinish a floor?
Not always. If the floor is only dull, a light screening or buffing and a fresh coat may be enough. Full sanding is for deep scratches, worn spots or removing old finish.
Should I sand wood floors wet or dry?
Floors are sanded dry. Wet sanding is for fine hand finishing on small projects, and water can raise the grain on a floor.
How do I know when the floor is smooth enough?
Wipe it clean and look across the surface in low, angled light. If you see swirl marks, scratches or glossy patches, sand those areas again with the last grit you used.
Shineboc 23CMSZ-CoarseMixBest overall
Pihemum 45PXSZZHWidest grit range
3M 9000NASimple 220 finishing refill