How to Properly Use a Tiller: Push or Pull, Depth and Technique
Let the tines do the work and guide the machine instead of forcing it. A front tine tiller pulls itself forward as the tines dig, so you hold it back and steer. A rear tine tiller is driven by its wheels, so you walk behind it and guide it. Till when the soil is slightly moist, make several shallow passes, and wear eye, hearing and foot protection.
Push or pull? It depends on the tine layout
Most people ask whether they should push or pull a tiller. In practice you do neither with much force. The tines are the engine of movement, and your job is to steer and control the pace.
On a front tine machine, the tines sit ahead of the wheels and bite into the ground. That bite tends to drag the tiller forward, sometimes faster than you want. You lean back slightly and hold the handles firmly to keep a steady walking pace. If the tiller lurches ahead, you are not holding it back enough. If it stalls and bounces in place, you may be holding back too much or the depth is too deep.
On a rear tine machine, the wheels drive the tiller and the tines trail behind. You mainly guide it. The Earthquake rear tine model on our comparison page also has counter-rotating tines that turn opposite to the wheels, plus a reverse gear for tight turns. With that design you walk behind the machine and steer, rather than wrestling it forward.
Get the ground ready first
Good results start before you turn the machine on. Pick a day when the soil is slightly moist but not soggy. Wet soil clumps and bakes into hard chunks, and very dry, compacted soil can make the tiller skip and bounce. A handful of soil should crumble when you squeeze it, not stay in a sticky ball.
Clear the area of rocks, sticks, hoses, landscape fabric and old roots, since these can jam or wrap around the tines. If you are breaking new ground, mow or cut the grass short first. Before you dig anywhere, mark and check for buried utility lines. In the US you can call 811 to have them marked for free.
Step-by-step: how to till a bed
Here is a simple routine that works for most electric, cordless and gas models. Always read the owner's manual for your exact machine, since controls and starting steps differ.
- Dress for the job: closed-toe boots, long pants, safety glasses and hearing protection for gas models. Skip loose clothing and dangling cords or strings.
- Set the depth. Use the wheels, drag stake or depth lever to start shallow. The BILT HARD front tine model lists flip-down wheels with four adjustable positions for this purpose.
- Plan your path. Start at one edge of the bed and work in straight, parallel rows.
- Start the machine on level ground with the tines clear of the soil. Let it reach full speed before it touches the ground.
- Lower the tines and walk at a slow, even pace. Let the tines chew in rather than pushing down on the handles.
- Overlap each pass slightly so no strips are skipped.
- Make a second pass at a right angle to the first, going a little deeper, until the soil looks loose and crumbly.
- Switch off, wait for the tines to stop fully, and unplug or remove the battery or spark plug cap before clearing anything stuck in the tines.
Match depth and passes to the job
Going straight to full depth is a common mistake. It overloads the motor and leaves big clods. Several shallow passes loosen the ground more evenly and are easier on both you and the machine.
Our tiller comparison lists depths from 6.6 in to 10 in. Seedbeds and weeding need less depth, while compacted clay and new ground call for the deeper end. Width matters too. The LawnMaster TE1318M and the BILT HARD both list an 18 in width, while the cordless models list 9 in and 9.5 in, so they need many more passes in an open garden. You can compare all of these numbers on our best tiller comparison.
Handling differences by tiller type
Each power source changes how you work. The table below uses the published specs from our comparison data.
Corded models need cable management. Keep the cord behind you and over one shoulder side of your path, and till away from the outlet so you never run over it. Use an outdoor-rated extension cord and a GFCI outlet in damp areas. The LawnMaster lists mechanical overload protection that shuts it off if a foreign object blocks it, but you should still stop and clear jams yourself with the power disconnected.
Cordless models give freedom but limited time. The SEYVUM lists 50 minutes of runtime and the reffmov lists 40 minutes per battery, so plan your beds in sections. Gas models need fuel handling: refuel only with the engine off and cool, and never run one in a closed garage or shed.
| Model | Power | Width | Depth | Weight |
|---|---|---|---|---|
| LawnMaster TE1318M | Corded electric | 18 in | 9 in | 24.36 lb |
| BILT HARD TOA-0456 (front tine) | Corded electric | 18 in | Not listed | 25 lb |
| Sun Joe TJ604E | Corded electric | 16 in | 8 in | 27.08 lb |
| EARTHQUAKE 39381 (rear tine) | Gas | 16 in | 10 in | 154 lb |
| SEYVUM MT8801 | Cordless battery | 9 in | 7 in | Not listed |
| reffmov SY-818 | Cordless battery | 9.5 in | 7 in | 10 lb |
Common mistakes and safety reminders
Most problems come from rushing. A few habits prevent almost all of them.
- Do not till wet soil. It forms hard clumps that are tough to break up later.
- Do not force the machine down with your weight. Let the tines dig at their own pace.
- Never reach near the tines while the machine is powered. Disconnect power first.
- Keep children, pets and bystanders well away. Tillers can throw stones and soil.
- Wear eye protection every time, and hearing protection with gas engines.
- Be careful on slopes. Work across or up and down in a way that keeps your footing secure, and never let a heavy machine pull you downhill.
After tilling: finish and store
Once the bed is loose, rake out roots and stones, then mix in compost if the soil needs it. Avoid tilling again and again, since constant churning can break down soil structure over time.
Clean dirt and plant fibers off the tines and housing. Fold the handle if your model has one. The LawnMaster, BILT HARD and Sun Joe all list folding handles, which helps with storage. Store batteries indoors and follow the maker's guidance for gas storage. If you are still deciding which machine suits your garden, the side-by-side tiller specs are a good place to start.
Frequently asked questions
How often should I till my garden?
Most beds only need tilling once a year when you prepare them for planting, or when you are breaking new ground. Once the soil is loose, light cultivating between rows is usually enough.
Can I use a tiller to remove grass?
Yes, but cut the grass short first and make several passes. Shake out or rake off the sod pieces afterward so the grass does not regrow.
Can I till right after rain?
Wait until the soil has dried a bit. If it sticks to your boots or forms a ball in your hand, it is too wet.
Should the tines spin before they touch the soil?
Yes. Start the tiller with the tines lifted clear, let it reach full speed, then lower it into the ground slowly.
LawnMaster TE1318MBest overall
BILT HARD TOA-0456Wide front-tine option
EARTHQUAKE 39381Deepest, for hard ground