Guide

How to Make Your Own Woodworking Vise

The easiest way to make a woodworking vise is to build a Moxon style vise: two hardwood jaws pulled together by threaded rod or wooden screws and clamped to your bench edge. It needs basic hand or power tools and a weekend. If you need deep, heavy clamping on a thick bench, a cast iron vise is usually the better route, so check the specs before you commit.

Updated 2026-11-13 · Based on published specifications and maker information

Top picks from our best woodworking vise comparison

Choose the style of vise to build

Homemade vises fall into a few families. Each trades build effort against holding power, so pick the one that matches the work you actually do.

A Moxon vise is the best starting point. It is a pair of jaws that sits on top of your bench or clamps to its edge, which makes it good for dovetails and hand-tool work. A face vise or leg vise is a bigger project, but it bolts to the bench and handles heavier planing and chopping.

StyleBest forMain hardwareDifficulty
Moxon viseJoinery at a comfortable heightTwo screws or threaded rods, nuts, handlesEasy
Clamp-on wood visePortable and small projectsThreaded rod, G-clamps or bench clampsEasy to moderate
Face vise with screwGeneral bench workLarge wooden or steel screw, guide railsModerate
Leg viseHeavy planing and choppingLarge screw, pin or parallel guideHarder

Gather materials and tools

Choose dense hardwood such as maple, beech or oak for the jaws. Soft wood dents and flexes under pressure, and a flexing jaw is the main reason homemade vises feel weak.

Here is a typical list for a Moxon style build:

  • Two straight hardwood boards for the jaws, thick enough that they do not bow when tightened
  • Two threaded rods or wooden screws, with matching nuts and washers
  • Handles, wing nuts or hardwood knobs to turn the screws
  • Leather or cork to line the jaw faces
  • Drill with bits sized to your rods, plus a square and marking gauge
  • A saw, chisel and clamps for cutting the nut mortises
  • Sandpaper and a simple finish such as oil

Build a Moxon style vise step by step

Work slowly on the holes. If the rod holes are not square to the jaw face, the vise will pinch at one end and slip at the other.

  • Mill both jaw boards flat, straight and to the same size. Plane or sand the faces until they sit tight against each other.
  • Clamp the two jaws together face to face and mark the rod hole positions across both boards. Keep them well away from the ends so the wood does not split.
  • Drill the holes using a drill press if you can. If you drill by hand, use a block or guide to keep the bit square.
  • On the front jaw, cut shallow mortises on the outside face so the nuts sit flush and cannot spin. Epoxy them in or lock them with a wood plug.
  • Thread the rods through the back jaw and into the front jaw nuts. Add washers behind the handles so the wood does not crush.
  • Line the inside faces with leather or cork, which protects your work and helps it grip.
  • Test with scrap. Tighten both handles evenly and watch for racking, which is when the jaw tilts instead of closing parallel.

Improve grip and reduce racking

Even jaw pressure matters more than raw strength. Turn the two screws a little at a time, alternating sides, so the front jaw stays parallel.

A toed-in jaw, where the top closes slightly before the bottom, pulls work down and tight. You can copy the idea by planing a very slight angle on the inside of your jaw. Our guide to the best woodworking vise explains why toed-in jaws and wood facing provision show up on better models, and the same logic applies to your build.

For a face vise, add a guide rail or parallel bar under the screw. Without one, the jaw swings under heavy side loads. Keep the jaw faces wide enough to cover the stock you plan to hold, since narrow jaws can only grip a small area.

Stay safe while you build and use it

Wear safety glasses whenever you cut, drill or sand, and hearing protection with power tools. Clamp your jaw boards firmly before drilling, because a bit that grabs can spin the board hard.

Keep fingers clear of the jaws as they close, and never reach in while someone else turns the handle. Tighten only as much as the work needs. Overtightening a wood vise can crack the jaws or strip the nuts.

If you choose a metal screw build that involves welding, you need a proper welding helmet, gloves, fire-safe surroundings and ventilation. Skip it if you have no welding experience, and use store-bought threaded rod instead.

When a store-bought vise makes more sense

A homemade vise is great for light to medium work. It has limits, though. Wood screws wear, handmade threads slip, and you need good skills to get the jaws parallel.

Published specs show what you would be trying to match. The Jorgensen 41012 has 10 in jaws and a 13 in opening, with a ductile or forged iron body, quick release and toed-in jaws. It weighs 39 lb and fits benches up to 3 in thick. The Fetcoi wood bench vise, by comparison, is a clamp-on beech build with a 7.87 in opening and a weight of 13 lb, which is close to what a well-made wooden project could offer.

Smaller options show the other end. The IRWIN 226361 opens 4.5 in for light-duty woodworking and mounts under the bench. The IRWIN listing weight is 1 lb, which looks like an outlier, so verify it before buying. Our woodworking vise comparison lines up all of these specs in one place so you can see whether your build would be enough.

Frequently asked questions

What wood works best for homemade vise jaws?

Dense hardwoods such as maple, beech or oak resist denting and bowing. Avoid soft pine for the moving jaw, because it flexes under load.

Can I make a vise without welding?

Yes. A Moxon vise uses store-bought threaded rod, nuts and handles, with no welding at all. Wooden screws are another route if you have the right cutting tools.

Do I need to drill my bench to mount it?

Not for a Moxon style or clamp-on build, since it grips the bench edge with clamps. A face vise or leg vise usually needs bolts or lag screws into the bench.

How do I stop the jaw from slipping on my work?

Line the jaws with leather or cork, tighten both screws evenly and keep the faces flat. A slight toe-in at the top also helps hold the piece.

Compare the products