How to Load a Staple Gun with 6mm Staples
Open the magazine, slide in a strip of 6mm staples with the legs pointing toward the outlet, close it until it latches, and test fire into scrap wood. Before you load, confirm your gun accepts a 6mm (about 1/4 in) leg length and the right crown width, because many all-purpose guns start at a longer size.
Check that 6mm staples fit your gun first
Loading is easy, but the wrong staple is the most common reason for jams. A staple has two measurements that matter: leg length and crown width. The crown is the flat top that spans the two legs. Your gun is built for specific staple types, and the model name or a stamp on the magazine usually tells you which.
A 6mm staple is about 1/4 in, which is the low end of the 1/4 to 3/8 in range we describe on our best upholstery staple gun for beginners page. Short staples are a good match for fabric and thin frames. Many multi-type guns list 5/16 in as their shortest size, though. In the specs on that page, the SHALL 3-in-1 lists 5/16 in D-type staples and the NEU MASTER 3-in-1 lists 5/16, 3/8 and 1/2 in sizes. None of the product data we have names 6mm as supported, so read your gun's manual or markings before buying a box of 6mm staples.
If the staples are even slightly too narrow for the channel, they can tilt. If the legs are too short for the gun's drive stroke, they may fire unevenly. When in doubt, match the staple's marked type to the gun's marked type.
Know your magazine style
Staple guns open in a few different ways. Look at your gun before you start, because the loading steps change slightly with each style. Our comparison data lists the magazine design for most models.
| Magazine style | Where it opens | Models in our data |
|---|---|---|
| Bottom-load | Underside of the gun, by the front | YEAHOME ST12, YEAHOME YHHT-003, Topec T8085, NEU MASTER NHT0050 |
| Rear-load | Back of the gun, with a release button | Arrow HT50 hammer tacker |
| Drop-in | Top or side channel that the strip drops into | Jonard TriggerTack cable stapler |
Safety before you open the magazine
Staple guns are simple, but a staple fired by accident can injure a hand or an eye. Take a minute to set up safely before you load.
Keep the gun pointed at a scrap surface or the floor, never at yourself or another person. Rest your fingers on the grip only, not across the outlet at the nose. Wear safety glasses, because staples can bounce back or ricochet off hard knots. If you are using an electric or pneumatic model, unplug it or disconnect the air supply first. A manual squeeze-style gun does not need a power source, so this step does not apply to it.
Step-by-step: loading a bottom-load gun
Most upholstery staple guns on our comparison page use a bottom-load steel magazine. The steps below fit that design. Your gun may differ in small details, so use them as a general guide.
- Point the gun away from you and keep your hand off the trigger or handle squeeze.
- Find the latch or release at the base of the magazine. Press or slide it so the magazine tray comes free.
- Pull the tray out and check that it is empty. Remove any bent or leftover staples.
- Take a strip of 6mm staples and place it in the channel with the legs pointing down, toward the outlet. The flat crowns should sit on top.
- Slide the tray back in until the latch clicks. If it does not click, the strip may be sitting crooked, so open it and reseat the staples.
- Squeeze once against a piece of scrap wood to confirm a staple fires and sits properly.
Loading a rear-load or drop-in gun
A rear-load gun, like a hammer tacker, has a button or latch at the back. Press it, pull the rail back, and place the staple strip in the channel with the legs pointing toward the front. Then push the rail forward until it locks. The idea is the same as a bottom-load gun, but the strip enters from the other end.
A drop-in design has an open channel. You lay the strip into it and close a cover or push a spring-loaded follower forward. Whichever style you have, the legs always point toward the outlet, and the spring pusher should press the strip gently forward. If the strip rattles loose or the pusher does not move, the staples are probably the wrong size.
Test your depth and clear jams
Once the gun is loaded, test it on a scrap of the same material you plan to work on. Several models in our data have a power or depth adjustment. The YEAHOME ST12 uses a screw lever, the SHALL 3-in-1 uses a stepless knob, and the Topec uses a knob. Start low and raise the power until the staple sits flush without cutting through fabric. Short 6mm staples often need less power than longer ones, so go slowly.
If a staple jams, stop and point the gun at a safe surface. Models with a jam-clearing system, like the SHALL and Topec, let you open the nose and pull the stuck staple free. On other guns, open the magazine and remove the staple with pliers. Never put your fingers near the outlet while a staple is stuck, because it may release suddenly.
If jams keep happening, check three things: the staples are the correct type, the strip is not bent, and the magazine is clean. Using a different brand of staple than the gun was made for can also cause trouble.
Quick tips for smooth results
A few habits make everyday stapling easier. Store staples in a dry place so they do not rust or stick together. Load only strips that are straight and undamaged. If you must cut a strip to fit a half-empty magazine, cut between staples rather than through one. Finally, when you finish, unload the gun or store it with the magazine closed and out of reach of children.
Frequently asked questions
Are 6mm staples the same as 1/4 inch staples?
Nearly. Six millimeters is about 0.24 in, so people often call them 1/4 in staples. Always check the marked leg length on the box.
Why does my staple gun double-fire or skip?
This usually means the staple type is wrong, the strip is bent, or the power setting is too high or too low for the material. Try a fresh strip and test on scrap.
Can I mix staple sizes in the magazine?
No. Mixed sizes can sit unevenly and jam. Load one size and type at a time.
How do I know when the magazine is empty?
Some guns, such as the NEU MASTER, have a viewing window that shows the staple level. On other guns, you may feel the squeeze go slack or see the pusher reach the nose.
YEAHOME ST12Best overall
SHALL S001001BEBest power control
Jonard Tools STG-100Cable stapler, not upholstery