How to Install a Submersible Pump in a Drilled Well
To install a submersible pump in a drilled well, cut power at the breaker, connect the pump to the drop pipe and a check valve, splice the motor cable with waterproof connectors, and lower the assembly on a safety rope to a set depth above the well bottom. Then connect it to the pitless adapter, seal the well cap, and wire the pressure switch and control equipment. If your pump needs 230V wiring or you are unsure about the well, hire a licensed electrician or well professional for those parts.
Before you start: check the pump and the well
Confirm the pump suits your well before you touch anything. Casing diameter, well depth, static water level and the voltage on your circuit all matter. Every pump on our best well pumps submersible page fits 4 in or larger casings, but you should still measure your casing and read the driller's well log.
Check that the pump's head covers the well depth, the rise to the house and the tank pressure. Also confirm your supply voltage matches the pump. Some listed pumps run on 115V and others need 230V, and a 230V pump on the wrong circuit will not work properly.
Safety first: well work combines electricity, water and heavy loads. Turn off the breaker for the well circuit and lock or tag the panel so nobody switches it back on while you work. Wear safety glasses and gloves, and never work alone at a wellhead.
Gather the parts and tools
Most installs need the same basic kit. Having everything laid out before you open the well avoids leaving the casing uncovered while you run to the store.
- Drop pipe (rigid PVC or poly pipe rated for well use) or flexible pipe, sized to match the pump discharge
- A check valve at the pump, plus an additional one higher in the line if your pump's maker recommends it
- Torque arrestors to keep the pump centered and stop it twisting at startup
- Stainless steel safety rope, rated well above the combined weight of the pump, pipe and water
- Waterproof wire splice kit (heat-shrink or gel-filled) and nylon cable ties or tape
- Pitless adapter and well cap, if your well does not already have them
- Pressure switch, pressure tank and, if your pump uses one, a control box
Know your pump's wiring type
Wiring is where pumps differ most, so read your manual before you buy fittings. Some pumps have the starting capacitor built into the motor, so no separate control box is needed. Others use a three-wire design with an external control box near the tank.
Here is how a few pumps from our comparison page are set up, based on their published specs.
| Pump | Voltage | Starting setup |
|---|---|---|
| VEVOR 3 HP deep well | 230V | External control box, 33 ft cord |
| Hallmark 1 HP MA0414X-7A | 230V | Built-in capacitor start, no control box |
| Wassermann 4STM4 1 HP | 230V | 2-wire with built-in control box |
| VERIWIS 3/4 HP | 115V | Built-in capacitor start |
| Holdwell S 1 HP | 115V | Built-in controller |
Step-by-step installation
The order below suits a typical drilled well with a pitless adapter. Follow your pump's manual where it differs, and keep the cable and pipe clean as they go into the casing.
- Switch off power at the breaker and confirm it is dead with a tester.
- Remove the well cap and inspect the casing for debris. If you are replacing an old pump, pull the old pump, pipe and wire first. This is heavy work, so use a proper pulling tool or call a pro for deep setups.
- Attach the check valve and the first length of drop pipe to the pump discharge. The listed pumps here use 1-1/4 in discharge connections, so match your fittings to that. Use thread sealant suited to potable water.
- Tie the safety rope to the pump's lifting eye. Never rely on the pipe or the power cable to carry the weight.
- Splice the pump's motor leads to the drop cable using waterproof connectors. Do not skip this, since a poor splice is a common cause of early failure.
- Lower the pump slowly, adding pipe sections. Every 10 ft or so, tape or tie the cable and rope to the pipe so they do not tangle. Add a torque arrestor just above the pump if your setup calls for one.
- Stop when the pump reaches the planned setting depth. Fix the pipe to the pitless adapter or well seal and secure the rope to the cap.
- Seat the well cap, run the cable through the sealed fitting, and wire the pressure switch, tank and control box (if used). Leave final electrical connections to a licensed electrician if you are not qualified.
Setting depth and sediment
Place the pump below the lowest water level you expect during heavy use, and well above the bottom of the well. A pump sitting in silt wears quickly and can clog. Your driller's records usually show the static level and the recommended depth range.
For a newly drilled well, sediment is common early on. Some pump listings, including the VEVOR and Holdwell models, suggest adding a layer of gauze in front of the intake screen for new wells with granular sediment. Check your own pump's instructions before modifying the intake.
Never run a submersible pump dry. Overload protection helps in a fault, but it does not replace a proper water level. The VEVOR and Holdwell listings both warn against operating without water or at a very low level.
Pressure switch, tank and first start
Once the pump is in, the rest of the system controls when it runs. The pressure switch turns the pump on and off based on tank pressure. If you are replacing yours, see our best well pump pressure switch comparison for how to match the settings to your system.
Before restoring power, check that all fittings are tight and the tank is set to the correct air pressure for your switch's cut-in setting. Then switch the breaker on and open a faucet to purge air. Water may run cloudy for a while in a new well.
Watch the first cycles: the pump should start, fill the tank and shut off cleanly. Short, rapid cycling, tripping breakers or unusual noise means you should switch off and recheck wiring and tank pressure.
When to call a professional
You can do much of the plumbing yourself, but call a well professional if the pump hangs deep in a long well, if the casing is damaged, or if sizing is in doubt. Call a licensed electrician for any 230V work or changes at the service panel. Local codes often require permits and sealed well caps, so check your rules first.
Frequently asked questions
Can I install a submersible pump in a dug or open well?
Yes, but the setup differs. Without a pitless adapter, you usually hang the pump on a rope with a flexible hose and keep it a safe distance above the bottom. Always keep the water source covered and protected from contamination.
Do I need a control box?
Only if your pump is built that way. Some models have a built-in capacitor or controller, so no external control box is needed, while others, like the VEVOR 3 HP listing, ship with an external one.
Why use a second check valve?
A built-in check valve helps prevent backflow, but several listings recommend adding an extra one for better protection. Check your manual for the spacing it suggests.
How long does an install take?
It depends on well depth, the old equipment and your experience. A shallow replacement can be a few hours, while a deep well with new wiring takes longer. Plan for extra time rather than rushing wiring and splices.
VEVOR Deep Well Submersible PumpBest for deep wells
H HALLMARK INDUSTRIES INC MA0419X-12ABest 2 HP pump
VERIWIS 4SWP5.8-0.75/115VBest 115V option