How to Install a Car Lift in a Garage Step by Step
Installing a garage car lift comes down to four jobs: confirm the space, floor and power will work, set the columns in place, anchor them to the concrete, and then assemble, fill and test the lift before any car goes on it. A two-post lift is a two-person job that needs a forklift or similar equipment for unloading and a dedicated 220V supply. Follow your lift's manual for anchor and slab specifications, and have a licensed electrician handle the wiring.
Check the Space, Floor and Power First
Most installation problems start before the lift arrives. Measure your ceiling height, the garage door track and opener, and the clear floor area around where the lift will stand. Then compare those numbers to the lift's overall height and footprint on its spec sheet.
Overall height varies a lot. On our best residential garage car lifts page, overall lift height runs from 97 to 167 in, so a lift that fits one garage may not fit another. Remember that a raised vehicle sits in front of the columns, and a garage door opener or low light fixture can get in the way.
- Ceiling: confirm the overall height of the lift fits under the lowest obstruction, including door tracks and openers.
- Floor: two-post lifts are anchored into the slab, so the concrete must meet the thickness and strength in the manual. If you are unsure, ask a contractor to check it.
- Power: most lifts here need a 220V supply. Plan the outlet or hardwired connection location before you set the columns.
- Space: leave room to walk around the lift, open car doors and move tools.
Know Which Lift Size You Are Installing
Weight and height affect how you handle the parts. The lifts below come from our comparison data. Heavier lifts need stronger equipment to move the columns and more helpers on installation day.
Pick a capacity above your heaviest vehicle. Also check that the overall height still fits your ceiling, since the tallest model in this group is much taller than the others.
| Lift | Capacity | Overall height | Lift weight |
|---|---|---|---|
| KATOOL AM120SD | 12000 lb | 143.7 in | 1369 lb |
| KATOOL 10000 lb 2-post | 10000 lb | 110.25 in | 1256 lb |
| KATOOL H120D | 12000 lb | 111 in | 1200 lb |
| Jack Boss ASJR-245LD | 10000 lb | Not listed | Not listed |
Gather Tools and Plan the Delivery
These lifts ship as heavy crates, and the listings for the models above state that the buyer is responsible for unloading and that a forklift is needed. If you cannot unload it, some sellers offer shipping to a local terminal for pickup. Sort this out before delivery day.
Check the crate for damage before the driver leaves. The listings advise taking photos and marking any damage on the receipt, which is a sensible habit with any freight.
- Forklift or similar equipment for unloading and moving columns
- Hammer drill and the masonry bit size named in the manual
- Torque wrench and a socket set
- Level, tape measure and chalk line
- Hydraulic fluid specified by the manufacturer
- Helpers: plan on at least two people for any column work
Step-by-Step Installation of a Two-Post Lift
The exact order varies by brand, so treat this as a general outline and let your manual win if it differs.
Work slowly. Anchoring is the step you cannot easily undo, so double-check the layout before you drill.
- Mark the layout. Snap chalk lines for the column positions and confirm the spacing against the manual. Check that a vehicle can drive between the columns and that the doors can open.
- Unload and unpack. Lay out all parts and match them to the parts list before assembly.
- Stand the first column. Set it on the marked spot and keep it plumb with a level. Ask a helper to steady it while you work.
- Position the second column. Fit the base plate or overhead parts if your model uses them, and check the spacing again.
- Drill the anchor holes. Use the bit size and depth in the manual. Clear dust from each hole before inserting the anchors.
- Set and torque the anchors. Tighten to the specified torque. If an anchor spins or the concrete cracks, stop and get advice before continuing.
- Install the carriages, arms, cables or chains as the manual shows. Many lifts here use dual hydraulic chain-drive cylinders, and the Jack Boss uses a chain with steel wire rope cables. Set the tension as directed.
- Connect the hydraulic lines and power unit, then fill with the fluid the manual names.
- Have an electrician connect the 220V supply to the power unit.
- Bleed the system and cycle the lift empty several times. Check that both sides rise evenly and that the safety locks click in together.
Test Before You Lift a Car
Run the lift through full up and down cycles with no vehicle on it. Watch the cables or chains, listen for unusual noises, and check for fluid leaks at every fitting.
Then do a low test lift with your vehicle, raising it just off the ground. Check that it is level and that the arms and pads sit on the lift points shown in the vehicle's manual. Lower it onto the locks and check that they hold.
Most models here use a lock release. The KATOOL AM120SD and H120D, and the Jack Boss, list a single-point lock release, which frees the locks on both sides from one spot. Learn how yours works before you need it.
Safety Notes
Lifting a vehicle is serious work, so treat the install and daily use with care.
Electricity: 220V can be dangerous. Use a licensed electrician, a properly rated circuit and the wiring sizes in the manual.
Weight and heights: never stand under a lift that is not resting on its locks. Never exceed rated capacity, and keep people and pets clear while the lift moves.
Eye and hearing protection: wear safety glasses when drilling concrete and hearing protection with a hammer drill. Dust masks help too.
Inspection: check anchors, cables or chains, and hydraulic fittings on a regular schedule, and stop using the lift if anything looks worn or loose.
When to Choose a Different Lift
If your slab is thin or your ceiling is low, a two-post lift may not be the right fit. A four-post lift is easier to install and works well for parking and storage, as covered on our garage car lift comparison.
If you are still deciding on size and type, compare capacity, overall height and lock features side by side before you buy. Getting that right makes the installation much smoother.
Frequently asked questions
Can I install a car lift by myself?
It is not a good idea. The columns are heavy and need to be held steady while you align and anchor them. Plan for at least two people and proper lifting equipment.
Do I need a permit?
Rules vary by city and county, and electrical work often needs a permit. Check with your local building department before you start.
Can I install a two-post lift on any concrete floor?
No. The slab must meet the thickness and strength in the manual, and it should be in good condition without cracks near the anchors. If you are unsure, get a professional opinion.
How long does installation take?
It depends on your experience, the lift model and the electrical work. Set aside a full day with helpers and extra time for the wiring and testing.
KATOOL AM120SDBest overall
KATOOL 10000Best for lower ceilings
Jack Boss ASJR-245LDHighest 2-post lift height