How to Drill at a 90-Degree Angle
To drill a hole at 90 degrees, line the bit up square to the surface with a combination square, a drill guide or a drill press. Then start slowly and check the angle from two sides. If you mean drilling in a space too tight for a regular drill, a right angle attachment turns the drive 90 degrees so the bit can reach.
Two jobs behind one phrase
People search for "drill at a 90-degree angle" and mean one of two things. Some want a hole that runs straight into the material, square to the surface. Others need the drill itself to work sideways, such as inside a cabinet or between two joists, where a normal drill body will not fit.
The first problem is about technique and alignment. The second is about tool shape. This guide covers both, starting with the straight hole, since that is the more common job.
Drilling a square hole, step by step
The most common mistake is a slight tilt that you cannot see while you are looking down the drill. A small error at the surface becomes a bigger one as the hole gets deeper, so it pays to set up the angle before the bit touches the material.
Here is a simple routine that works with any corded or cordless drill:
- Mark the hole with a pencil, then make a small dimple with a center punch or a nail so the bit has a place to start.
- Pick a bit that matches the job. For a large hole, drill a smaller pilot hole first.
- Stand a combination square on the surface next to the bit, and check that the bit sits parallel to the blade.
- Move 90 degrees around the work and check again from the side. One view is not enough.
- Start at low speed with light pressure until the bit bites, then raise the speed.
- Let the bit do the cutting. On deep holes, back the bit out now and then to clear chips.
- When drilling all the way through, clamp a scrap board behind the work to reduce tear-out.
Aids that keep the bit square
You do not need special gear to drill straight, but a few aids make it easier. The right choice depends on how many holes you have and how precise they need to be. If you are shopping for a drill to do this kind of work, our best drill page compares the main options side by side.
The table below sums up the common methods.
| Method | Best for | Watch for |
|---|---|---|
| Combination square as a visual guide | Occasional holes with any drill | Needs two checks from different sides |
| Drill guide or jig | Repeated holes and dowel joints | Guide hole must match the bit size |
| Drill press | Precise, repeated holes in small workpieces | Work must fit under the press and be clamped |
| Bubble level on the drill | Level horizontal holes in a wall | Only as reliable as the surface it references |
When the drill will not fit
Sometimes the angle is fine but the space is not. Inside a cabinet, behind an appliance or between joists, there is no room for the drill body behind the bit. A right angle drill attachment solves this. It clips into the chuck or hex holder and turns the drive 90 degrees, so the drill sits to the side while the bit works in the gap.
Head height is the spec that decides whether one fits. Measure the opening first, then compare against the numbers. Our best right angle drill attachment page puts these on one spec sheet. Here are the published figures for five of them.
| Attachment | Head height | Length | Weight | Impact rated |
|---|---|---|---|---|
| DEWALT DWAMRAFT | 1.5 in | 9.2 in | 0.71 lb | Yes |
| DEWALT FLEXTORQ Modular System | 1.5 in | 16.5 in | 1.53 lb | Yes |
| Titan 16189 | 1.5 in | 5.5 in | 0.55 lb | Not listed |
| AUTOTOOLHOME 00069 | Not listed | 2.36 in | 0.2 lb | Not listed |
| DEWALT DWAMRA38FT (3/8 in square drive) | 1.5 in | 9.3 in | 0.83 lb | Yes |
Using an attachment well
An attachment makes the job possible, but it changes how the tool behaves. You lose some feel for the bit, and the body can twist in your hand. Check the maker's listing for what each attachment is meant to do, since many are built mainly for driving screws and nuts. If you use one often, a dedicated tool may suit you better, and our best right angle drill page covers those.
A few habits help:
- Brace the attachment. The Titan listing mentions an extension handle, and the AUTOTOOLHOME lists a thumb flange for this purpose.
- Respect the speed limit. The AUTOTOOLHOME lists a 400 RPM maximum, and the Titan lists 3000 RPM.
- Use an impact rated attachment with an impact driver. The DEWALT models above are listed that way.
- Choose a magnetic bit holder if you want to hold a screw with one hand. The DEWALT DWAMRAFT, the system kit, the Titan and the AUTOTOOLHOME list magnetic retention.
- Start slowly and keep the drill body from swinging as the bit bites.
Safety notes
Drilling is routine, but a few hazards deserve attention every time.
Before drilling into a wall, ceiling or floor, think about what is behind it. Hidden electrical wires and water or gas pipes are real risks. Switch off power to nearby circuits when you can, and use a stud and pipe detector if you have one. Never drill near a suspected gas line.
Wear safety glasses, because bits can break or throw chips, especially in cramped spots. Add hearing protection for long sessions or when drilling masonry, and a dust mask when the material makes fine dust. Clamp small workpieces rather than holding them. Keep long hair and loose sleeves away from the chuck, and remove the battery or unplug the drill before changing bits. If you are working on a ladder, make sure it is stable and avoid overreaching.
Fixing common problems
If the bit wanders at the start, the dimple was probably too shallow or the speed too high. Make a clearer punch mark and begin slowly. If the hole ends up tilted, stop and re-check with the square before you go deeper. A hole that has already drifted is hard to correct, so it is better to catch it in the first few millimeters.
If the bit binds or smokes, back it out, clear the chips and ease off the pressure. Dull bits make all of these problems worse, so replace one that no longer cuts cleanly.
Frequently asked questions
Can you drill at an angle other than 90 degrees?
Yes. Use an angled drill guide or jig, or cut a small flat or notch at the start so the bit does not skate. Start slowly at the chosen angle, and keep the drill held steady in that line the whole time.
Why does my bit wander when I start a hole?
A smooth surface gives the tip nothing to grip. Make a small dimple with a center punch or nail, begin at low speed with light pressure, and for larger bits drill a smaller pilot hole first.
Do I need a drill press for straight holes?
No, but it helps for many identical holes or precise work. For a few holes, a handheld drill with a square or guide is usually enough if you check the angle from two sides.
Can I use a right angle attachment with an impact driver?
Only if it is made for it. The DEWALT models in our table are listed as impact ready. The Titan and AUTOTOOLHOME listings do not state an impact rating, so check the maker's guidance first.
DEWALT DWAMRAFTBest overall
DEWALT DWAMRASETFTBest system
Titan 16189Best compact