How to Check Tire Tread Depth with a Tire Gauge
Use a tread depth gauge, not a tire pressure gauge. Press the base flat across a tread groove, push the pin down until it touches the bottom, and read the measurement in 32nds of an inch. Check several spots on each tire, and plan to replace any tire that reads 4/32 or less, and replace it right away at 2/32 or less.
Pressure gauge vs. tread depth gauge
A tire pressure gauge and a tread depth gauge are two different tools. A pressure gauge measures the air inside the tire. A tread depth gauge measures how much rubber is left on the surface. If you only own a pressure gauge, it cannot tell you how worn your tires are.
A tread depth gauge is small and simple. It has a flat base, a barrel with a scale, and a thin pin that slides out of the barrel. Some are digital and show a number on a screen. Others are mechanical and show a number on a printed scale. Both do the same job.
The two checks still work well together. Pressure and tread wear are linked, so it makes sense to do both in the same session. Our best tire gauge page compares pressure gauges if you need one for that half of the job.
What you need and how to stay safe
You do not need much for this job. A tread depth gauge, a flashlight, a rag, and a pen and paper for your readings are enough. Gloves are a good idea because worn tires can hide small stones, glass, or exposed wire.
Safety comes first, especially if you work near the street.
- Park on level ground, set the parking brake, and turn the engine off.
- Work in a driveway or garage, not beside moving traffic.
- Never crawl under a vehicle held up only by a jack. Use jack stands if you lift it.
- Wear safety glasses if you clean out grooves with a pick or screwdriver. Debris can fly.
- If you see steel cords or belts showing through the rubber, stop driving on that tire and have it replaced.
How to measure tread depth step by step
Check the tires when they are cool and the car has been parked for a while. Clean the grooves first so dirt and pebbles do not give a false reading.
Follow these steps for each tire:
- Push the pin all the way into the barrel and press the gauge base against a flat surface. The scale should read 0/32. If it does not, the gauge may be damaged or need a reset.
- Pull the pin back out and set the gauge on the tire, with the base resting across the tread ribs and the pin over a groove.
- Hold the gauge square to the tire, not tilted. A tilted gauge reads wrong.
- Press the base firmly so it sits flat on the tread, and let the pin drop to the bottom of the groove.
- Read the number at the edge of the barrel. On a mechanical gauge, you may need to lift it away carefully without moving the pin. A digital gauge will show the number on its screen.
- Write the reading down, then move to a new spot and repeat.
How to read the 32nds scale
Tread depth in the US is usually given in 32nds of an inch. A reading of 6 means 6/32 of an inch of tread is left. The smaller the number, the more worn the tire. Many gauges also have a millimeter scale if you prefer metric.
New tires often start somewhere around 10/32 to 11/32, though this varies by tire type. Use the table below as a quick guide to what your reading means.
| Reading | What it means | What to do |
|---|---|---|
| 8/32 and above | Plenty of tread left | Keep checking monthly |
| 5/32 to 7/32 | Moderate wear | Check more often and watch for uneven wear |
| 4/32 | Wet-road grip is dropping | Start shopping for replacements |
| 3/32 | Getting low | Replace soon, especially before winter or rainy season |
| 2/32 or less | At or below the legal minimum in most states | Replace right away |
Where to measure on each tire
One reading is not enough. Tires can wear unevenly, and the worst spot decides when you should replace the tire.
Measure in at least three places across the tread: near the inner edge, in the center, and near the outer edge. Then repeat at a few points around the tire. Rolling the car a little lets you reach spots that were against the ground.
Compare the numbers. If one edge is much lower than the rest, the tire is wearing unevenly. Use the lowest reading when you decide whether to replace the tire.
What uneven wear tells you
The pattern of wear often points to a cause. Fixing the cause helps your next set of tires last longer.
Wear on both outer edges often means the tire runs underinflated. Wear down the middle often means it runs overinflated. Wear on only one edge can point to an alignment problem. Patchy or cupped wear can come from worn suspension parts or tires that are out of balance.
Pressure is the cause you can fix at home. A reliable gauge lets you set each tire to the number on the sticker inside the driver's door jamb. If you also want to add air when a tire is low, our best tire gauge inflator page compares options that combine both jobs. Alignment and suspension problems need a shop.
The penny and quarter backup tests
No tread depth gauge handy? Coins give a rough check. Place a penny into a groove with Lincoln's head pointing down. If you can see the top of his head, the tread is at about 2/32 or less, and the tire needs replacing.
For a margin of safety, try a quarter with Washington's head pointing down. If the top of his head is covered by tread, you have more than about 4/32 left. If you can see all of it, start planning for new tires.
Coins are only a rough guide. A gauge gives you an exact number you can track over time, which makes it easier to see how fast a tire is wearing.
How often to check
Check tread depth about once a month, and before any long trip. Many people pair it with a monthly pressure check so both get done on the same day. Keep a note of each reading. If a tire drops quickly between checks, something is off, and it is worth finding out why.
Also look at the tire sidewalls and tread for cracks, bulges, nails, or cuts. Tread depth alone does not tell you everything about a tire's condition. Age and damage matter too.
Frequently asked questions
Can I use a digital tire pressure gauge to measure tread?
No. A pressure gauge reads air pressure through the valve stem. Tread depth needs a gauge with a probe that sits in the tread groove.
Should I measure when the tires are hot or cold?
Tread depth does not change much with temperature, so you can measure at any time. Pressure readings are best taken when the tires are cold.
Do I need to check the spare tire?
Check its pressure and look for cracks. Spare tires rarely wear down, but they can age and lose air while they sit unused.
Do all four tires wear at the same rate?
Not always. Front tires often wear faster on front-wheel-drive cars. Rotating the tires on the schedule in your owner's manual helps even things out.
AstroAI ACTGT1BU-USBest overall
AstroAI ATG180Best simple digital gauge
ETENWOLF T300Best in extreme weather