How to Check Ignition Timing With a Timing Light
Connect the light's power leads to the battery, clamp the inductive pickup on the number one spark plug wire, and aim the flashing light at the timing marks while the engine idles. The flash freezes the marks, so you can read where the pointer sits and compare it with your engine's specification. If it is off, loosen the distributor hold-down bolt, turn the distributor slightly, and check again.
Before you start: know your target
A timing light only shows you where the timing is. It does not tell you where it should be. Find your engine's specified base timing, usually printed on an underhood sticker or listed in the service manual. The sticker also tells you the idle speed to use and whether to disconnect or plug the vacuum advance hose.
Next, confirm that your ignition system works with a timing light. Most lights suit distributor and DIS systems, and many do not work with coil-on-plug, CDI or MSD ignitions. Check the specs on your light before you hook anything up. Our best timing light page lists the ignition compatibility for each model.
Safety first
Timing is checked with the engine running, so the hazards are real. Take a minute to set up safely.
- Keep hands, leads and clothing away from the fan, belts and pulleys. Route the light's cables clear of moving parts and hot exhaust manifolds.
- Park on level ground with the parking brake set and the transmission in park or neutral, as the manual directs. Chock the wheels.
- Work outside or with strong ventilation. Exhaust contains carbon monoxide, which you cannot smell reliably.
- Wear safety glasses. Fuel and hot parts are close by.
- Do not stare into the strobe, and never place the light on a hot engine part. Spark plug wires carry high voltage, so touch only the insulated boots, and only with the engine off.
- Connect or disconnect the power leads with the engine off.
Step by step: checking timing
Here is the basic routine for a typical distributor engine. Your service manual may add steps for your model.
- Warm the engine to normal operating temperature, then shut it off.
- Find the timing marks. They are usually a notch on the crank pulley and a scale on the timing cover. Clean the area with a rag and mark the correct notch with white paint or chalk so it stands out.
- Connect the light's power clips to the battery, red to positive and black to negative. Keep the leads clear of the fan.
- Clamp the inductive pickup around the number one spark plug wire. Point the arrow on the clamp toward the spark plug, and seat it fully.
- Follow the manual for the vacuum advance hose. Many engines call for disconnecting and plugging it.
- Start the engine and let it settle at the specified idle speed. A built-in tachometer helps you confirm this.
- Aim the light at the marks and squeeze the trigger. The pulley mark will appear to stand still against the scale.
- Read where the mark sits relative to the pointer and compare it with the specification.
How to read the marks
On the timing cover, a scale shows degrees before top dead center (BTDC) on one side of zero and after top dead center (ATDC) on the other. The pulley notch is frozen under the strobe, and its position against that scale is your timing. If the notch lines up with the 10 mark and the spec is 10° BTDC, you are on target.
Take a clear look from straight on. Viewing from an angle can make the mark seem off by a degree or two. If the mark flickers or jumps around, check that the pickup is seated on the right wire and facing the correct direction.
If you cannot see the marks even with the light, the pulley or cover may be coated in grime. Wipe it clean with the engine off, then try again.
Using a light with a dial or digital advance
Digital advance lights work a little differently. Instead of reading the scale by eye, you use the dial or buttons on the light to delay the flash until the pulley notch lines up with a fixed reference, often the zero mark or pointer. The number on the screen then shows the actual timing in degrees.
Here is the routine. Aim the light at the marks with the engine idling. Turn the advance control until the notch sits exactly on the reference. Read the degrees on the display. That reading is your timing at that moment.
This method is handy when the marks are hard to read, or when you want to see how much timing the engine adds as RPM climbs. Raise the engine speed slightly and repeat the process, keeping your hands clear of moving parts. Compare the readings with the advance curve in your manual.
Setting the timing
If the reading does not match the specification, you can adjust it on most distributor engines. With the engine off, loosen the distributor hold-down bolt just enough that the distributor turns with some effort. Restart the engine and aim the light at the marks.
Turn the distributor a small amount. Rotating it one way advances the timing, and the other way retards it. Check which direction applies to your engine in the manual. Move slowly, then watch the marks settle after each change.
When the marks line up with your target, shut off the engine and tighten the hold-down bolt. Start the engine, check the marks once more, and reconnect the vacuum advance hose if you removed it. Finally, take the engine up in RPM briefly to confirm there is no pinging or hesitation.
Choosing a light that fits your engine
If you do not own a timing light yet, match it to your ignition system first and your preferred features second. The table below uses published specifications. All five list a 0 to 90° digital advance range.
For a wider comparison of strobe type, weight and extras, see our timing light comparison.
| Light | Max RPM | Ignition compatibility | Engine types |
|---|---|---|---|
| OBDMONSTER N300 Pro | 9999 | DIS, conventional, electronic, computer-controlled | 12V gasoline, 2 and 4 stroke |
| KZYEE KT60 | 10000 | Distributor-equipped; not most coil-on-plug | 2 and 4 stroke gasoline |
| Innova 5568 | 9990 | Breaker point, electronic, DIS; not MSD | 2 and 4 cycle |
| Innova 3568 | 9990 | Conventional, electronic, computer controlled | 4 cycle only |
| ANCEL LT70 PRO | 9999 | Distributor-based 9-16V ignition, not CDI | 2 and 4 cycle gasoline |
Frequently asked questions
Why does my timing change when I rev the engine?
Most distributors add timing as RPM rises, using centrifugal weights, and sometimes add or remove more through vacuum. This is normal. Base timing is checked at the specified idle speed, and the manual gives the expected advance at higher speeds.
Do I need to disconnect the vacuum advance?
Often yes, but it depends on the engine. The underhood sticker or service manual will say whether to disconnect and plug the hose. If you skip this when it is required, the reading will be wrong.
Can I use a timing light on a diesel engine?
No. Diesel engines do not use spark plugs, and the lights covered here are built for gasoline engines. Two of the listings say so directly.
What if the timing mark is not visible?
Turn the engine off and clean the pulley and timing cover. Marking the notch with white paint or chalk usually fixes the problem. If the marks are worn away, look up the engine's marks in the manual before you adjust anything.
OBDMONSTER N300-US3Best overall
KZYEE KT60Highest RPM reading
Innova 5568Lightest pro light