Guide

How to Change Rotary Tool Bits and Accessories

Unplug the tool or remove the battery, press the spindle lock, loosen the collet nut or keyless chuck, swap the bit, and tighten again by hand or with the supplied wrench. Push the shank in far enough to be gripped securely, then check that it spins true before you start working. Discs and sanding drums mount on a mandrel, a small shaft that the collet holds.

Updated 2026-11-12 · Based on published specifications and maker information

Top picks from our best rotary tool comparison

Start with safety

Changing an accessory puts your fingers right next to a cutting edge, so make the tool incapable of starting first. On a corded tool, unplug it. On a cordless tool, remove the battery or at least engage the lock-off switch if your model has one.

Accessories can also be hot after use. Cutting and grinding wheels in particular hold heat for several minutes, so let them cool before you grab them. Wear safety glasses whenever you run the tool, and add hearing protection and a dust mask for long sessions or dusty materials. Cutting discs can shatter, so always inspect them for cracks before mounting.

How the pieces fit together

Most rotary tools hold accessories with the same small set of parts. Knowing the names makes the steps below much easier to follow.

The collet is a slotted sleeve that squeezes around the shank, which is the thin metal stem of a bit. The collet nut threads over the collet and tightens it. The spindle lock is a button that stops the shaft from turning so you can loosen or tighten the nut with one hand. Some tools skip the collet and use a keyless chuck, which works like a tiny drill chuck.

If you are still choosing a tool, the way it holds accessories is a good thing to compare. Our best rotary tool page puts popular models side by side so you can see which chuck or collet style each one uses.

Changing a bit with a collet nut

This is the traditional method and works on most corded and cordless models. Take your time and avoid forcing anything.

  • Switch the tool off and disconnect power or remove the battery.
  • Press and hold the spindle lock button. Turn the shaft slightly if the button does not engage right away.
  • Unscrew the collet nut counterclockwise. If it is snug, use the wrench that came with the tool.
  • Pull out the old bit. If it is stuck, wiggle it gently while keeping the lock pressed.
  • Slide the new bit's shank into the collet. Insert it far enough for a firm grip, but leave the working part clear of the nut.
  • Tighten the nut clockwise until the bit cannot be pulled out. Snug is enough, so do not crank on it.
  • Release the spindle lock, reconnect power, and run the tool briefly away from your face to confirm the bit spins without wobble.

Keyless chucks and quick-change systems

Some tools let you change accessories without a wrench. A keyless chuck opens and closes by hand, while quick-change designs use a twist-and-click collar. The steps are similar: stop the spindle, loosen the collar, insert the shank, and tighten by hand.

These systems are fast, but they depend on a clean fit. Dust and resin build up inside the chuck jaws over time, which can reduce grip. Wipe the shank before inserting it and blow out debris from the chuck now and then. Check your manual for which shank sizes your chuck accepts, since not every accessory fits every system.

Battery tools often suit this kind of frequent swapping, because you can work anywhere without a cord in the way. Our best rotary tool cordless comparison covers those models if that fits how you work.

What a mandrel is and how to use one

A mandrel is a small shaft with a screw or stud at the end. You attach discs, polishing wheels or sanding bands to the mandrel, then clamp the mandrel in the collet like any other bit. Cutting discs, felt wheels and many sanding drums all need one.

To mount a disc, hold it against the mandrel head, thread the screw through the center, and tighten it until the disc sits flat. Make sure the screw head sits below the working edge, or it can scratch your workpiece or catch on it. Then chuck the mandrel in the collet using the steps above.

If a disc looks off-center or wobbles when spinning, stop and remount it. A tilted disc can grab and kick back.

Matching accessories to the job

Different accessories do different work, and each has a preferred speed and technique. The table below gives a general overview. Always follow the speed guidance printed on the accessory packaging.

Light pressure is better than heavy pressure with nearly all of them. Let the speed do the work, and keep the tool moving so heat does not build up in one spot.

AccessoryTypical useHow it mounts
Burr or cutterShaping wood, metal or plasticShank in the collet
Grinding stoneSharpening, deburring metalShank in the collet
Cutting discSlicing thin metal or plasticMandrel in the collet
Sanding drumSmoothing curves and edgesMandrel or integral shank
Polishing wheelBuffing metal and plasticMandrel in the collet
Engraving bitFine detail on hard surfacesShank in the collet

Fixing common problems

Most trouble comes from one of a few causes. If the nut will not loosen, press the spindle lock fully and use the wrench for extra leverage. If the bit slips, the collet may be worn or the wrong size for the shank, so check that the collet matches the bit.

If you feel heavy vibration, the shank may be bent, the bit may not be seated deeply enough, or the collet may be dirty. Remove the accessory and replace the bit if it looks damaged. Never keep using a bent or chipped accessory.

If you do long grinding or sanding jobs near an outlet, steady power can matter more than portability. See our best corded rotary tool page for corded options that suit that kind of work.

Frequently asked questions

Do I need to turn the tool off before pressing the spindle lock?

Yes. Always stop the tool completely and let the shaft stop spinning before pressing the lock. Pressing it while the shaft turns can damage the mechanism.

How tight should the collet nut be?

Tighten it until the bit cannot be pulled out by hand, then stop. Over-tightening makes the nut hard to remove later and can wear the collet.

Can I use bits from another brand?

Often yes, if the shank diameter matches your collet. Check the shank size on the packaging and your collet size before buying.

How often should I replace the collet?

Replace it when bits begin slipping even after tightening, or when the slots look worn or damaged. Keeping it clean helps it last longer.

Compare the products