How to Adjust a Reel Mower for a Clean Cut
To get a clean cut, set the cutting height first, then adjust the reel so its blades just touch the fixed bedknife. A strip of paper should be sliced cleanly by the blades across the full width, with no heavy drag when you spin the reel by hand. Check both settings on a flat surface, and re-check them whenever the cut looks torn or ragged.
Why reel mower adjustment matters
A reel mower cuts like scissors. A spinning cylinder of curved blades sweeps grass against a fixed bedknife, and the grass is sheared between them. When the contact is right, the cut is crisp. When it is off, grass gets folded, chewed or missed.
Two settings control most of the result: cutting height and reel-to-bedknife contact. Height decides how much grass you remove. Contact decides how cleanly each blade is cut. Many cuts that look wrong are caused by one of these two being slightly off, not by a dull mower.
Because a push reel has no engine, it relies on a smooth, light spin. Blades that are too loose cut poorly, and blades pressed too hard make the mower heavy to push and wear the edges faster.
Safety first
The blades on a reel mower are sharp even when they are not moving, and the reel can turn suddenly if the mower rolls. Treat it with the same care as any cutting tool.
- Wear cut-resistant work gloves whenever your hands are near the reel.
- Wear safety glasses if you use a file, wrench or lapping compound, since metal bits and compound can fly.
- Wear hearing protection if you ever use a power drill to spin the reel for lapping.
- Work on a flat, stable surface and keep the mower from rolling by blocking a wheel or tipping it onto its handle with help.
- Never put fingers between the reel and bedknife, even to clear grass. Use a stick or brush.
- Keep children and pets away while you work.
Step 1: Set the cutting height
Start with height, because contact adjustments are easier once the mower sits at its working position. Most push reels raise or lower the cut by moving the front roller or the wheels, or by shifting the bedknife relative to them. Check your owner manual for which parts to move, and change both sides by the same amount so the reel stays level.
As a general rule, remove no more than about one third of the blade height in a single mowing. Cutting too much at once stresses the grass and leaves a rough finish. If the lawn has grown tall, raise the height for the first pass, then lower it a few days later.
Reels do best on short grass. Our best reel mower page lists the LawnMaster LMRM2001 at 1.3 to 2.6 in across 9 positions. That is a good example of the range to expect from a push reel. If your grass often grows beyond the top setting, a reel will struggle, so mow more often instead of raising the height too far.
Step 2: Check reel-to-bedknife contact
The reel blades should lightly touch the bedknife along its whole length. The easiest check is the paper test, which needs no special tools.
Park the mower on a flat surface and make sure your gloves are on. Then follow these steps.
- Slide a strip of ordinary printer paper between one reel blade and the bedknife.
- Turn the reel slowly by hand, so the blade pinches the paper against the bedknife.
- The paper should be cut cleanly, or at least held and snipped with light resistance.
- Repeat at the left end, the middle and the right end of the reel.
- If the paper is chewed, folded or not cut at all, the contact is too loose or uneven.
| What you see | Likely cause | What to do |
|---|---|---|
| Paper cuts cleanly at all three spots | Contact is correct | Leave it alone |
| Paper slips through or folds | Reel too far from bedknife | Tighten the adjustment slightly |
| Reel is hard to spin, or squeals | Contact too tight | Loosen the adjustment slightly |
| Cuts well on one side only | Reel and bedknife not parallel | Adjust each side separately |
Step 3: Make small, even changes
Most mowers have an adjustment screw or knob on each side of the reel. Turn each one a small amount, such as a quarter turn, then repeat the paper test. Small steps stop you from overshooting, and the same amount on both sides keeps the reel parallel to the bedknife.
If one side cuts paper and the other does not, adjust only the loose side until both match. Then spin the reel by hand. It should turn freely with a light brushing sound and no grinding.
Some models differ in where the adjusters sit, so follow the diagram in your manual. If your mower has a cutting-height setting that moves the bedknife, recheck contact after every height change.
Step 4: Test on the lawn and fine-tune
Mow a short strip of dry grass and look at the tips. A clean cut leaves even, flat ends. Torn tips look frayed and turn pale or brown within a day or two.
Wet grass is harder to cut cleanly, so test on dry turf when you can. Walk at a steady pace, since pushing too slowly can cause the reel to spin unevenly and miss grass.
If you still see uncut strands, the cause may be one of these:
- Dull blades or a worn bedknife that need sharpening or replacing
- Grass that is too long for the chosen height
- A stiff or dirty reel that is not turning freely
- Contact that is slightly loose at one end
Keeping the adjustment right
After each mow, brush off clippings and wipe the blades. Dried grass and dirt add drag and can pull the reel out of true over time. A drop of light oil on moving parts, as the manual suggests, keeps things turning smoothly.
Recheck the paper test at the start of each season and after any hard knock, such as hitting a stone. If adjusting no longer gives a clean cut, the blades likely need sharpening. Lapping or a professional sharpening service can restore the edge.
If you are still deciding on a mower, remember that a true reel is the only type that cuts this way. Our best reel mower comparison explains how width, weight and height range differ. For example, the LawnMaster LMRM2001 is 20 in wide and weighs 30.2 lb, which suits small, flat lawns.
Frequently asked questions
How often should I adjust my reel mower?
Check it at the start of each season and any time the cut looks ragged. Also recheck after a collision with a hard object or after storing it for a long time.
Why does my reel mower leave strands of uncut grass?
The most common causes are loose reel-to-bedknife contact, dull blades, or grass that is too long for the height setting. Do the paper test, then try a higher height and mow again a few days later.
Should the reel blades touch the bedknife?
Yes, lightly. They should make contact along the whole length without heavy drag. Too much pressure wears the edges and makes the mower hard to push.
Can I adjust a reel mower on uneven ground?
It is better not to. Use a flat surface so the reel, wheels and roller sit level. That makes both height and contact easier to judge.
EGO Power+ LM2134SP-2Best overall
Greenworks MO60L427Widest cutting path
LawnMaster LMRM2001Only true reel mower