How Much Thickness Can a Thickness Planer Remove?
A thickness planer removes a thin layer on each pass, and a common safe range for benchtop machines is about 1/16 to 1/8 inch. Total removal is not limited by a single number, because you make as many passes as you need, down to the machine's minimum board thickness. The listings we compare also give a maximum board thickness (6 in on most benchtop models) and, on some, a maximum depth of cut.
Two limits: depth per pass and board thickness range
People often mix up two different numbers. The first is how deep the cutterhead can bite on one pass. The second is the range of board thicknesses the machine accepts, from its thinnest to its thickest setting.
Depth per pass is what answers the question most directly. Total removal is just depth per pass multiplied by the number of passes. If you need to take off 3/8 inch and your comfortable cut is 1/16 inch, that is six passes. Nothing stops you from doing that, except time and the minimum thickness the machine will accept.
Many makers do not publish a maximum depth of cut. Of the listings on our page, the Jet 20 in model is one that does, at 3/32 in per pass. For the others, a depth stop or depth gauge tells you what you are setting, and the manual is the place to confirm the limit.
What a typical pass looks like
Light passes give a cleaner surface, put less load on the motor and reduce tearout. Heavier passes remove stock faster but are harder on the machine and the wood. As general woodworking practice, many people keep cuts to roughly 1/16 to 1/8 inch, and take lighter cuts on wide boards, dense hardwoods and figured grain.
Width matters because the cutterhead has to remove material across the whole board at once. A 12 in wide board needs far more cutting force than a 3 in wide one at the same depth. If a wide board makes the motor strain, lower the depth rather than forcing it.
The last pass should be very light. A finishing pass of around 1/32 inch leaves a smoother surface and is a common way to finish a board.
How the listed specs relate to removal
Most of the benchtop models on our best thickness planer page plane boards up to 13 in wide and 6 in thick. That 6 in figure is the tallest workpiece that fits, not the amount you can remove. The WOODERS listing gives a height range of 1/4 to 6.3 in, which also tells you the thinnest board it accepts.
Here is what the listings say about depth and thickness. Blank cells mean the listing does not give the number.
Depth control is also where the machines differ most in practice. The Cutech lists an 8-position depth stop for repeating the same thickness across a batch of boards, and a scale showing how much the next pass will remove. The WEN lists an onboard material removal gauge. The VEVOR M1B lists 1/8 in depth control increments.
| Planer | Max board thickness | What the listing says about depth |
|---|---|---|
| Cutech 40800H | 6 in | 8-position depth stop and a depth of cut indicator |
| WEN PL1337 | 6 in | Depth stop and onboard material removal gauge |
| Jet JWP-208HH-BLK | 8 in | 3/32 in cutting depth per pass, 1/16 in height scale |
| WOODERS PL13-15AB | 6.3 in | 1/4 to 6.3 in height range, indicator from 0 to 1/8 in |
| VEVOR M1B-LS-3301 | Not listed as a spec (6 in height in listing text) | 1/8 in depth control increments |
How to remove a lot of stock safely
If you have a rough board that is much thicker than you need, work in stages instead of trying to cut it in one go. Here is a simple routine.
Between passes, check the board for movement. Wood can cup or twist as stress is released, and that changes how it sits on the bed.
- Measure the board at its thickest point and decide your target thickness.
- Set the first pass light, around 1/16 inch, and run the board through.
- Flip the board end for end or side to side on later passes if you want to keep the cuts even and watch for grain direction.
- Take the same light depth each time until you are within about 1/32 inch of the target.
- Finish with one very light pass and measure again.
- Use the same setting for every board in a batch so the thicknesses match.
Feed speed, cutterhead and finish
Slower feed rates make more cuts per inch, which gives a finer surface. The Cutech and WEN both list a 16 fpm low speed for tearout-prone wood, and the WEN also lists 26 fpm for faster dimensioning. The DEWALT DW735 lists 96 or 179 cuts per inch from its two-speed gearbox.
Cutterhead type affects finish too. Spiral heads with many small inserts, such as the 26 on the Cutech and WEN, are described by makers as cutting quieter and reducing tearout. We compare published specifications only, so noise and finish claims here are the makers' own.
Snipe is the small dip at the start or end of a board. A shallower cut helps reduce it, and several listings mention anti-snipe designs. If you are comparing models, our best thickness planer for the money page puts these features side by side.
Safety notes
Planers throw chips at high speed and run loud. Wear eye protection and hearing protection every time, and connect a dust collector or vacuum to the dust port to reduce airborne dust.
Unplug the machine before changing knives, inserts or clearing a jam. Keep hands clear of the infeed and outfeed, and never plane boards with loose knots, nails, screws or other metal. The Jet listing says it is built for wood, not metal or plastic, and the same caution applies to any planer.
Do not run very short boards. The Jet lists a minimum board length of 6-3/4 in, and other makers set their own limits, so check your manual.
Frequently asked questions
Can I remove more than 1/8 inch in one pass?
Only if your manual allows it. Narrow boards of soft wood may handle a deeper cut, but wide or dense boards usually give better results with lighter passes.
What is the thinnest board a planer can handle?
It varies by model. The WOODERS listing gives a 1/4 in minimum in its height range, but many listings do not publish a minimum. Check the manual before you plan thin stock.
Why does my planer leave rough patches?
Common causes are cutting too deep, feeding too fast, dull knives or inserts, or planing against the grain. Try a lighter cut and the slower feed speed.
Does a wider planer remove more per pass?
Not necessarily. Width sets the widest board you can plane, while depth per pass depends on motor power, cutterhead and the settings the maker allows.
CUTECH 40800HBest overall
WEN PL1337Spiral head with warranty
DEWALT DW735Easiest knife changes