How Long Does a Board Have to Be to Go Through a Planer?
For most benchtop thickness planers, a board should be at least about 12 inches long, and longer is safer. The real rule is that the board must be longer than the gap between the infeed and outfeed rollers, so it is always gripped. Check your manual for the exact minimum, because makers set it by model.
The short answer on minimum length
A common rule of thumb for benchtop planers is a minimum of about 12 inches. That is a general guideline, not a number from any single spec sheet. Some owners run shorter pieces on their machines, but most manuals warn against it.
Why does the number vary? It comes down to how far apart the feed rollers sit. If a board is shorter than that gap, it is not held by both rollers at once, and the planer can lose control of it. Your manual lists the true minimum for your machine, so treat 12 inches as a starting point and look up the real figure.
Why short boards are a problem
A planer pulls a board in with the infeed roller, cuts it at the cutterhead, and pushes it out with the outfeed roller. For a clean, safe cut, the board needs to touch at least one roller at all times.
When a board is too short, three things can go wrong:
- The board can stall or stop moving under the cutterhead and leave a gouge.
- The cutterhead can grab the piece and throw it back toward you (kickback).
- The ends can dip, which makes snipe worse because the board has almost no flat middle.
Minimum length by machine type
Published minimum length is not always listed. Among the models on our best thickness planer page, the product data gives a minimum board length only for the Jet. The others leave it out, so check the manual before you buy or plane anything small.
The table below shows the size specs we have for four models and whether a minimum length is published.
| Model | Max width | Max thickness | Published minimum length |
|---|---|---|---|
| Cutech 40800H | 13 in | 6 in | Not listed |
| WEN PL1337 | 13 in | 6 in | Not listed |
| DEWALT DW735 | 13 in | 6 in | Not listed |
| Jet JWP-208HH-BLK | 20 in | 8 in | 6-3/4 in |
Why the Jet can handle shorter stock
The Jet listing gives a 6-3/4 inch minimum board length. It is a 20 inch floor machine that weighs 640 lb, not a benchtop tool, so its roller layout is different. Do not assume a 13 inch benchtop model can take pieces that short.
If your model does not list a minimum, stay with the 12 inch guideline or go longer. A longer board is easier to feed and gives more flat surface in the middle.
What about maximum length?
In theory, a planer has no maximum length. What limits you is support. A long board that hangs off either end will tip, and that pushes the cut deeper at the start or end.
Some listings mention table length. The VEVOR M1B-LS-3301 lists a 28.2 inch worktable, which is the surface that holds the board. Boards longer than that need extra support such as roller stands or a helper. Folding extension tables, where your model has them, should be set level with the bed.
How to plane a short piece safely
If your project needs short parts, you do not have to run them through one at a time. Plane the stock while it is still long, then cut it to size afterward. This is the simplest and safest method.
If you must plane something that is already short, try these steps:
- Glue or tape short pieces to a longer carrier board so the rollers always have something to grip.
- Run several short pieces end to end, with the ends touching, so the next piece pushes the last one through.
- Take light passes only, because a deep cut grabs a short piece harder.
- Keep fingers well clear of the infeed opening and stand to the side of the board's path, not behind it.
Safety and snipe notes
Wear eye and hearing protection every time. A planer is loud, and chips and splinters can fly. Unplug the machine before you change knives or inserts, and never reach into the machine while it is running.
Check the wood before you plane it. Nails, screws and grit damage the cutterhead, and loose knots can break free. Do not run end grain through a planer. Manuals commonly warn against it because the board can split or kick back.
On snipe, which is a dip at the start or end of a board, a long board helps. Many planers on our page list an anti-snipe design, such as the Cutech with its four lead screws. Even so, plan to cut a few extra inches off each end. If you are choosing a machine for this reason, our thickness planer comparison shows which models list anti-snipe features.
Frequently asked questions
Can I plane a board thinner than my planer's minimum thickness?
Not directly. Each planer has a lowest setting, and the manual lists it. For thinner stock, glue the piece to a flat carrier board or use a sled, then take light passes.
Does board width change the minimum length?
The roller gap sets the minimum length, not the width. Wide boards are heavier, though, so they need more support and a slower feed. Check that the board is within your planer's width rating.
Should I joint a board before planing it?
Yes, if the board is warped. A planer presses a bowed board flat while it cuts, then the board springs back. Flatten one face first, then plane the other face to match.
Is a slower feed rate better for short boards?
A slower feed gives a finer finish and puts less strain on the board. Two-speed models such as the Cutech and WEN list a 16 fpm low setting. Use it for figured wood and for short stock when you must plane it.
CUTECH 40800HBest overall
WEN PL1337Spiral head with warranty
DEWALT DW735Easiest knife changes