How to Use Vise Grips the Right Way
Open the jaws, set the adjusting screw so the pliers close with firm hand pressure, then squeeze until the handles snap over center and lock. Release by pressing the trigger or lever. Match the jaw style to the part, wear eye protection, and keep fingers out of the pinch zone.
What Vise Grips Actually Do
Vise grips are locking pliers. Unlike ordinary pliers, they lock shut on a part, so you can let go of the handles and the jaws keep their grip. That makes them useful as a small portable clamp, a way to hold a stripped or rounded bolt, and a spare hand when you are working alone.
The name comes from the original IRWIN brand, but many makers sell the same style of tool. The technique below works for most of them, whether you own one pair or a full set. If you are still deciding what to buy, our best vise grips comparison lines up the published specs side by side.
Pick the Right Jaws and Size First
Most mistakes come from using the wrong jaw shape. Curved jaws wrap around round or rounded parts. Long nose jaws reach into tight spaces. Straight jaws suit flat material, and a locking C-clamp holds parts together, much like a regular clamp.
Size matters too. Sevens and tens are the most useful sizes for general work. Smaller pliers suit fine work, and larger ones grip bigger parts. Jaw capacity varies by model, so check it before you start. For example, the IRWIN 4-inch long nose pliers list a jaw capacity of 1 5/8 inches, and the DEKOPRO set lists 1-3/4 inches for its 7-inch curved pliers and 2-1/2 inches for its 10-inch pair.
| Jaw style | Best for | Watch out for |
|---|---|---|
| Curved jaw | Round stock, pipe, rounded or stripped nuts | Can mark soft material |
| Long nose | Tight spaces, small fasteners, staples, narrow parts | Smaller grip area, so go easy on force |
| Straight jaw | Flat material and edges | Does not wrap round parts well |
| Locking C-clamp | Holding two pieces together, reaching around edges | Needs room for the open frame |
Set the Jaw Width With the Adjusting Screw
The screw at the end of one handle controls how far the jaws close, and that decides how much clamping force you get. Set it too loose and the pliers lock without gripping. Set it too tight and you cannot close them at all.
The simple method is to place the open jaws around the part, then turn the screw until the handles need a firm squeeze to close. Back the screw out to loosen the grip, and turn it in to tighten. Once set, the screw usually stays put, so you can repeat the same grip on identical parts.
Clamp and Lock: Step by Step
Once you know how the screw works, the whole process takes a few seconds.
- Choose the jaw style and size that fit the part.
- Open the handles fully by pressing the trigger or release lever.
- Turn the adjusting screw until the jaws are just wider than the part.
- Seat the part deep in the jaws, close to the pivot, where the grip is strongest.
- Squeeze the handles until they snap past center and lock.
- Test the grip with a gentle tug. If it slips, open the pliers, turn the screw in a quarter turn, and try again.
- To release, press the trigger or lever. Many models open with one hand.
Common Jobs and How to Handle Them
For a stripped or rounded bolt, use curved jaws and clamp as tightly as the part allows. Seat the nut or bolt head deep in the jaws, lock, and turn slowly. If the grip slips, tighten the screw a little and clamp again. Expect the fastener to be damaged, so this is a rescue method, not a first choice.
As a clamp, lock the pliers across the work and check that the part sits flat. A C-clamp style fits better when you need to hold two flat pieces together or reach around a lip or bend. As a third hand, lock onto a small part so you can solder, drill or file it without holding it with your fingers.
Long nose pliers are good for pulling staples, holding small fasteners and gripping narrow stock. Some models, including the WORKPRO 7-inch curved pliers and the IRWIN long nose and curved models, have a built-in wire cutter near the jaw hinge. Use it on soft wire only, and never on live wire.
Safety Notes and Mistakes to Avoid
Locking pliers store a lot of squeezing force, and the jaws can slip suddenly. A few habits keep you safe and protect your tools.
- Wear safety glasses. Teeth can slip off a part, and wire or metal bits can fly when you cut.
- Keep fingers clear of the pinch point between the handles and the jaws.
- Do not use vise grips on a good nut or bolt head if a wrench or socket fits. The teeth round the corners.
- Never use them on live electrical wiring. Turn off and unplug power first, and do not rely on the handle grip as insulation.
- Do not hammer on the handles or add a pipe for extra leverage. That can bend the jaws or crack the pivot.
- Avoid gas, brake and other pressurized fittings. Slipping or crushing the part could cause a leak.
- Do not use them to support heavy loads or as a lifting point.
Care and Storage
Wipe off dirt and moisture after use, especially if you work outdoors. Nickel plating, such as on the Crescent and SK sets, helps resist rust, but it does not make the tool maintenance free. Put a drop of light oil on the pivot and screw now and then so they move easily.
Store the pliers open or with the screw backed off slightly, so the spring and lock mechanism are not kept under stress. If the jaws no longer meet squarely or the lock feels mushy, replace the pliers rather than trusting them with a clamping job. When you are ready to add a different jaw style to your toolbox, our best vise grips picks show which sets include curved, long nose and C-clamp options.
Frequently asked questions
Why won't my vise grips lock?
The adjusting screw is usually too loose, so the jaws never build enough pressure to pass center. Turn the screw in a little and try again. If that does not help, check the jaws for wear or dirt.
Can I tighten the grip further after locking?
On some models you can. The Crescent set, for example, has a hex key receiver in the adjusting screw, so you can turn it with a hex key after the first grip is set. Do not force it past what the part can take.
Which size should I buy first?
A 7-inch curved jaw pair covers most household jobs. Add a 10-inch pair for larger parts, and a long nose pair if you often work in tight spaces.
Are vise grips a good substitute for a wrench?
Only as a last resort. Wrenches and sockets grip flat sides without damage, while vise grip teeth bite into the metal. Use the right wrench when the fastener is in good shape.
WORKPRO W031573Best single curved jaw
IRWIN 1602L3Best long nose
DEKOPRO DKHPLI003SET-S1GL-YBAZBest starter set