Guide

How to Get Vice Grips to Lock and Release

To lock vice grips, turn the adjusting screw until the jaws fit just barely open around the part, then squeeze the handles hard until the mechanism snaps over center and clicks. To release them, press the trigger lever (or pull the release lever on the handle) and the jaws open. If they won't lock or won't clamp tightly, the jaw gap needs adjusting with the screw.

Updated 2026-11-12 · Based on published specifications and maker information

Top picks from our best vise grips comparison

How locking pliers actually work

Locking pliers, often called Vise-Grips after the original IRWIN brand, use a toggle action. When you squeeze the handles, a linkage inside passes a tipping point called over center. Past that point, the handles hold the jaws shut on their own, with no hand force needed.

That is why the tool works as a portable clamp, a stripped-bolt remover and a third hand. It also explains the most common problem: the pliers only lock if the jaw gap is set correctly before you squeeze.

Step 1: Set the jaw opening with the adjusting screw

Most locking pliers have a screw in the end of one handle. Turning it changes how far apart the jaws sit when closed. Some models, including the SK set and the IRWIN 10 in straight jaw in our data, use a hex key or screwdriver through-hole on the screw for extra leverage, but you can usually turn it by hand.

  • Open the handles fully and set the pliers around the part.
  • Turn the screw clockwise to close the gap, or counterclockwise to open it, until the jaws just touch the part with the handles open.
  • Back the screw out a quarter turn or so if the pliers will not close in the next step.
  • Repeat until the handles close with firm hand pressure.

Step 2: Lock the pliers

Place the jaws square on the part. Squeeze the handles firmly with your whole hand until you feel and hear a click. The handles should now stay closed without any help from you.

If you can squeeze all the way with no resistance, the gap is too loose. Turn the screw clockwise a little, then try again. If you cannot close the handles at all, the gap is too tight. Turn the screw counterclockwise. A well set pair takes a solid squeeze to snap shut, then holds firmly.

Choose the jaw style for the job. Curved jaws grip round stock and rounded nuts, long nose jaws reach tight spots, straight jaws suit flat material, and C-clamp styles hold parts together. Our best vise grips comparison lays these styles out side by side.

Step 3: Release the pliers

Many modern pliers have a trigger release, a small lever inside the lower handle. Press it with your fingers or thumb and the handles spring apart, opening the jaws. The WORKPRO 7 in model, the DEKOPRO set and the SK set in our data all list a trigger release that works with one hand.

Some models, such as the IRWIN 4 in long nose in our data, do not list a trigger release. On pliers like that, a lever sits inside the handle that you pull or push to break the lock. Either way, hold the pliers firmly while you release. The handles can snap open quickly, so keep your fingers clear of the pinch point between them.

If the release feels stiff, you probably set the clamping pressure too high. Back the adjusting screw out a little before the next use.

How to loosen vice grips that are stuck

Pliers that will not open are usually clamped too hard, dirty or bent. Work through these fixes in order.

  • Turn the adjusting screw counterclockwise several turns to reduce pressure, then press the release.
  • Squeeze the handles a little tighter while pressing the release. This takes load off the mechanism.
  • Tap the release lever or the pivot area lightly with a hammer if it sticks.
  • Clean grit and rust from the pivots, then add a drop of light machine oil.
  • Check for a bent handle or jaw. Pliers that have been overloaded can deform and may no longer lock cleanly.

Choosing a pair that is easy to lock and release

Look for an adjusting screw that turns smoothly and stays set, a trigger release for one-handed use, and wear resistant steel. Our data lists chrome vanadium on the WORKPRO and DEKOPRO pliers, and heat-treated alloy steel on the IRWIN models. Sizes of 7 in and 10 in are the most useful for general work.

The table compares a few picks from our data on the features that affect locking and releasing.

Our vise grips comparison page has the full list if you want to compare more models.

ModelSizeTrigger releaseAdjusting screw
WORKPRO curved jaw7 inYesYes
IRWIN straight jaw 102L310 inYesYes
IRWIN long nose 1602L34 inNot listedNot listed
DEKOPRO 3-piece set7 in, 10 in, 6-1/2 in, 6 in C-clampYesYes

Safety notes

Wear safety glasses. A jaw can slip off a rounded or rusted part and the pliers can snap back toward your face. Keep fingers out of the pinch zone between the handles when you squeeze and release.

Do not use locking pliers on live electrical parts or as a substitute for the right socket or wrench on nuts that are still in good shape. They can round off fasteners and damage the surface of the part.

Frequently asked questions

Why won't my vice grips stay locked?

The jaw gap is probably too wide, so the handles never pass over center. Turn the adjusting screw clockwise a bit and squeeze again. Worn teeth or a bent jaw can also let the pliers slip.

Can I lock them without the adjusting screw?

Only if the jaw gap already suits the part. The screw sets clamping pressure for each job, so using it gives a more reliable lock.

Do I need a hex key to adjust them?

Usually not. Most screws turn by hand. A hex key or screwdriver can help on tight screws, and the Crescent set in our data has a hex key receiver on the screw.

Can vice grips damage the part they hold?

Yes. The hardened teeth bite into the surface. For soft or finished materials, use a different clamp or pad the jaws.

Compare the products