How Do Welding Magnets Work?
A welding magnet is a permanent magnet inside a shaped steel body that channels its pull into flat faces. Two steel pieces stick to those faces and stay at a set angle, so you can fit up and tack without clamps or extra hands. Ratings on the models we compare run from 25 lb to 77 lb, and heat is the main thing that can weaken them.
The short version
A welding magnet is a permanent magnet built into a shaped steel body. The body points the magnet's pull at flat faces, so steel pieces touch those faces and stay put. The faces meet at set angles, which lets you tack a joint without clamps or a helper.
Nothing plugs in and nothing switches on. The magnet pulls on any ferrous metal, meaning iron or steel. That is why these holders work well on mild steel and do nothing on aluminum or many stainless grades.
What is inside the holder
Most welding magnets sandwich permanent magnet material between steel plates. A bare magnet pulls in every direction, which wastes much of its force. The steel plates act as pole pieces. They gather the field and send it out through the working faces, where your workpiece touches. More contact area and a clean, flat surface give a better grip.
Arrow magnets are shaped so the faces meet at fixed angles. The arrow sets on our spec sheet list stops at 45, 90 and 135 degrees, and the YESWELDER set also lists 180 degrees. Press one plate against each face and the angle between them is already set.
Construction details vary. ARCCAPTAIN lists a riveted steel frame and guti-more lists an iron frame. The TOOLIOM adjustable model lists embedded ferrite magnets. Many listings say little about what is inside, so read the details before you decide.
What the holding force number means
Holding force is a pull rating in pounds. On the products we compare, the maximum ratings run from 25 lb to 77 lb. The 77 lb figure belongs to the adjustable TOOLIOM magnet, and the lowest maximum, 25 lb, is on the TOOLIOM arrow pack.
Treat the number as a ceiling. Ratings usually describe ideal contact: clean, flat, thick steel with the full face touching. Real jobs are rarely that tidy. A sideways load also slips more easily than a straight pull, so a magnet can lose its grip well below its rating when the work wants to slide.
- Rust, paint and mill scale add a gap between magnet and steel.
- Thin sheet cannot carry as much magnetic flux, so a bigger magnet may not grip better.
- Curved pipe touches only along a line, not a full face.
- Heat from the arc or a fresh weld weakens the magnet.
Fixed arrows or adjustable
Fixed arrow magnets are quick for repeat corners because there is nothing to set. An adjustable magnet covers odd angles but adds a joint you must tighten before welding. The TOOLIOM adjustable model lists a hex wrench for that lock, and the listing also shows a degree scale for repeating an angle.
The table below uses only the published specs. For the full ranking and short reviews, see our best welding magnets comparison.
| Product | Type | Angles | Max force | Pack |
|---|---|---|---|---|
| YESWELDER KY1101 | Arrow, fixed | 45, 90, 135, 180 degrees | 75 lb (25/50/75 mix) | 6 |
| TOOLIOM AJM-M | Adjustable | 20° to 200° | 77 lb | 1 |
| ARCCAPTAIN AR005 | Arrow, fixed | 45°, 90°, 135° | 55 lb (25/55 mix) | 4 |
| guti-more 25&55LB | Arrow, fixed | 45, 90, 135 degrees | 55 lb (25/55 mix) | 6 |
| TOOLIOM TL-FM1-XS | Arrow, fixed | 45, 90, 135 degrees | 25 lb | 4 |
Heat, arc blow and safety
Permanent magnets can lose strength when they get too hot. The TOOLIOM adjustable listing advises against welding directly next to the magnet body or exposing it to excessive heat. Tack your joint, then remove the magnet before you run the full weld.
Magnetic fields can also push a welding arc off course, a problem often called arc blow. Keep magnets away from the weld path and from the ground clamp area, and take them off once the tacks hold.
- Wear a welding helmet with the right shade and keep your eye protection on when grinding or chipping slag.
- Use welding gloves. Tacked steel and the magnet body can both be hot.
- Keep fingers clear when magnets snap onto steel. Strong ones can pinch.
- Keep magnets away from pacemakers and other implanted medical devices, and away from phones and cards.
- Weld with good ventilation, since fumes from steel and coatings are harmful to breathe.
Setting up a joint, step by step
The routine is the same for most fitup work. A little prep gives the magnet its best grip. If you are still choosing a set, our spec comparison shows how pack size and strength differ.
- Clean the contact areas down to bare steel with a wire brush or grinder.
- Place the two pieces on a flat, stable surface.
- Set a magnet on each side of the joint, using the stop or angle you need.
- Check the angle with a square before you strike an arc.
- Tack the joint, remove the magnets, then complete the weld.
- Let hot work cool before you handle it or put the magnets away.
Are welding magnets any good
They are good at what they are made for: holding steel at an angle while you tack. They are positioning aids, not clamps. They will not resist the pull of a weld that shrinks as it cools, so check the fit after each tack and be ready to adjust.
Match the tool to the job. Light sheet work suits lower ratings, while heavier plate calls for stronger magnets. Most joints need at least two magnets, so pack size matters as much as the pull rating.
Frequently asked questions
Do welding magnets work on stainless steel or aluminum?
They do not hold aluminum at all, because it is not ferrous. Many stainless grades are weakly magnetic or not magnetic, so grip is poor or missing. Magnetic stainless grades can hold, but the pull is often lower than on mild steel.
How many welding magnets do I need?
Most joints need at least two, one on each side. Packs on our sheet run from one to six magnets. A larger pack lets you support longer seams or keep spares, while a single magnet works as an add-on.
How should I store welding magnets?
Keep them on a flat steel plate or in a dry box, away from heat. Wipe off filings and spatter before use, since debris adds a gap that lowers grip. Store them apart from electronics.
Why does my welding magnet slip?
Slipping usually comes from rust, paint or scale under the faces, thin or curved metal, or a sideways load. Clean the contact area, choose a higher rating, or add a second magnet to share the load.
YESWELDER KY1101Best overall
TOOLIOM AJM-MAdjustable angles, highest force
ARCCAPTAIN AR005Steel-framed arrow set