Guide

How Do Vise Grips Work? The Locking Mechanism Explained

Vise grips, also called locking pliers, use a toggle linkage that passes slightly past its straight-line position. That "over center" point makes the jaws lock shut, so they hold a part without you squeezing. You set the clamping pressure with the adjusting screw and open the jaws with the release lever or trigger.

Updated 2026-11-12 · Based on published specifications and maker information

Top picks from our best vise grips comparison

The short version: a lever that locks itself

Regular pliers only grip while your hand squeezes. Vise grips are different because they lock. Once the jaws close on a part, the tool holds on by itself, so your hand is free for other work.

That is why people use them as a portable clamp, a way to grip a stripped bolt, or a third hand. The name comes from the original IRWIN brand, Vise-Grip, but the design is now sold under many names, including locking pliers, vice grips and mole grips.

The parts that do the work

A pair of locking pliers looks simple, but a few small parts work together. Knowing them makes it easier to understand how the tool behaves and what to look for when you compare models.

  • Fixed jaw and handle: one piece of steel that forms the stationary half of the tool.
  • Moving jaw: pivots on a pin and closes against the fixed jaw.
  • Movable handle: the lever you squeeze. It connects to the moving jaw through a linkage.
  • Adjusting screw: a threaded knob in the end of the fixed handle that sets how far apart the jaws sit when they lock.
  • Release lever or trigger: a small lever that pushes the linkage back past center so the jaws open.
  • Spring: helps open the jaws and keeps the mechanism moving smoothly.

Why the jaws stay locked

The key is a toggle linkage. When you squeeze the handle, the linkage straightens out. The pivot points line up, and then they go slightly past that straight line. This is the over-center position.

Past center, the force coming back from the clamped part pushes the linkage against a stop instead of pushing it open. The mechanism is stable in that position, a bit like a light switch that snaps and stays. This is often described as a bistable cam action, because the tool has two steady positions: open and locked.

The toggle also multiplies your hand force. A modest squeeze at the handle becomes a much stronger clamp at the jaws, which is why locking pliers can hold a rounded nut that regular pliers would slip off.

To unlock, the release lever pulls the linkage back across the center point. Once it is back on the open side, the spring and the handle movement let the jaws swing apart.

How the adjusting screw sets the pressure

The adjusting screw changes the starting gap between the jaws. The gap decides how far the linkage has to travel before it snaps over center, and that decides how hard the tool clamps.

If the screw is too loose, the pliers may close on the part without locking. If it is too tight, the handle may be hard to close. The right setting takes a little trial and error for each job. Several models in our data, including the WORKPRO 7 in curved jaw pliers, list an adjusting screw and a one-handed trigger release. Other models, like the IRWIN 4 in long nose, do not list one in the product data.

How to set and lock them

The process is the same on most locking pliers.

  • Open the jaws fully and place the part between them.
  • Turn the adjusting screw until the jaws just touch the part when the handles are about halfway closed.
  • Squeeze the handle firmly until it snaps over center and locks.
  • If it locks too easily, loosen the screw a little. If it will not close, tighten it less.
  • Press the release lever or trigger to open the jaws when you are done.

Jaw styles and what they grip

The locking action is the same in every version. The jaw shape decides which jobs the tool suits. Our best vise grips comparison covers each style, and the table below summarizes the basics.

Jaw styleBest forExample from our data
CurvedRound stock, rounded nuts and boltsWORKPRO 7 in curved jaw, with wire cutter
Long noseTight spaces, small fasteners, precise grippingIRWIN 4 in long nose, 1.625 in jaw capacity
StraightFlat material and edgesIRWIN 10 in straight jaw
Locking C-clampHolding parts together, reaching around edges6 in C-clamp in the DEKOPRO 3-piece set, 2 in jaw capacity

What to check when choosing a pair

Because the tool relies on a small linkage under heavy force, build quality matters. Look at the steel first. The WORKPRO model in our data uses chrome vanadium steel, while the IRWIN originals list heat-treated alloy steel with hardened teeth. Either can resist wear when well made.

Also look at the release and the screw. A trigger release lets you open the pliers with one hand, and a good screw makes it easy to set pressure for each job. If you want several sizes, a set such as the DEKOPRO 3-piece, with 7 in and 10 in curved pliers, a 6-1/2 in long nose and a 6 in C-clamp, covers more tasks than a single tool. You can compare these side by side on our vise grips page.

Safety notes

Locking pliers store a lot of force, so treat them with care.

Wear safety glasses. A part can slip, or a worn jaw can let go suddenly, and metal fragments can fly. Do not use locking pliers to hold a part on a live electrical circuit unless the handles are rated for it. Never use them as a hammer, and do not extend the handles with a pipe, since that can bend the linkage or break the tool.

Keep your fingers clear of the jaws and the handle gap. When the pliers are clamped on something under tension, release them slowly.

Frequently asked questions

Can vise grips damage a bolt or nut?

Yes. The hardened teeth bite into the surface, so they can mar a nut or round off its corners. Use a proper wrench or socket when the fastener is in good shape, and save locking pliers for stripped or rounded parts.

Why won't my locking pliers lock?

The adjusting screw is usually set too loose, so the linkage never reaches the over-center point. Tighten the screw a little and try again. If that does not help, a worn or damaged linkage may need replacing.

Why won't mine open?

Squeeze the handle slightly tighter first to take the load off the linkage, then press the release lever. If it is still stuck, back the adjusting screw out a few turns.

Can I leave them clamped for a long time?

They can hold a part for a long time, but check the grip now and then. Vibration or a shifting part can change the clamping force.

How do I care for them?

Wipe off dirt and moisture after use. Put a drop of light oil on the pivots and the adjusting screw thread now and then, and store them where they will stay dry.

Compare the products